Amiga ISO Collection/AmigaDemoCD2.iso/ASCII/TEXTE/MISC/BSC-ISDN.TXT

Text File | 1996-08-10 | 61.1 KB | 5,442 lines

@BEGIN_FILE_ID.DIZALL NEW BSC-MASTER ISDN PREFERENZES
@END_FILE_ID.DIZ
@ISDN: Lasat STI2 adapter
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$ The modem must be running 38400 baud before configuring
$ The baudrate must be locked at 38400 in the device setup.
^AT%R7^M
^AT&Q0^M
^AT\N0^M
^AT&D2^M
^AT&W^M
*Running ISDN is much faster than normal modems.

@ISDN: ISDN-blaster
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$ The ISDN-blaster is one of the few cards that has proper factory
$ settings. These cards are easy to install and uses the fossil driver.
^AT&F^M
^AT&W^M
*Running ISDN is much faster than normal modems.

@1200 bps without switches
1200


10
ATE1Q0V1X1S7=55S11=60S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@1200 bps with switches
1200


10
ATE1Q0V1X1S7=55S11=60S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
$U U D U D U U D
$Your modem is now configured for best performance.
$
$
$An option might be to add M0 to the modem initial string to
$silence your modem if you prefer.
$
* Your modem is now ready to go

@2400 bps without switches
2400


10
AT&C1&D2E1Q0V1X1S7=55S11=60S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@2400 bps with switches
2400


10
ATE1Q0V1X1S7=55S11=60S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
$U U D U D U U D
$Your modem is now configured for best performance.
$
$
$An option might be to add M0 to the modem initial string to
$silence your modem if you prefer.
$
* Your modem is now ready to go

@ACEX 9600 v.32
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^ATV1&C1&D2X1\J0\N3\Q3^M
*Your ACEX 9600 modem is ready to go

@Anchor 2400i Internal Half-card
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
^ATE1Q0M1X4V1S7=60^M
^AT&C1&D2&W^M
*Your 2400 baud modem is ready to go

@AST 2X9600
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$ Switch Settings:    FRONT 1 2 3 4 5 6 7 8 9 10
$                           U D D U D U U D * *
$
$                     REAR  1 2 3 4 5 6 7 8
$    *=Not Used             D D D U D U U *
^AT&F^M
^AT&C1&D2\J0\N3\Q3\V1&W^M
*Your AX9624c is now configured for 19200 baud operation.  Be sure
*to set ALL your dialing directory entries to 19200 to get the
*best speed on all calls.

@AT&T Model 4000
1200


10
ATV1E1Q0X2S7=45S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@ATI 2400etc (non V.42)
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F1^M
^AT&C1&D2&W^M
*Your ATI 2400etc modem is ready to go  You can set all of your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you.  MNP operation has also been enabled.
*Remember to Exit/Save from SETUP to save these changes

@ATI 2400etc/e & 2400etc/i (with V.42)
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F2^M
^AT&C1&D2&W^M
*Your ATI 2400etc modem is ready to go  You can set all of your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you.  MNP operation has also been enabled.
*Remember to Exit/Save from SETUP to save these changes

@ATI 9600etc/e V.32/V.42
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F2^M
^AT&C1&D2&W^M
*Your ATI 9600etc modem is ready to go.  You can set all of your
*dialing directory entries to 38400 baud and the modem will handle
*speed conversions for you.

@Avatech 2400E
2400


10
ATE1Q0V1X4&C1&D2S7=55S11=60S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Boca v.32bis 14400 FAXmodem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0&K3\N3^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&C1&D2X4S0=0^M
^AT&K3\N3&W^M
*Your Boca is ready to go
*
*Set DTE speed to 19200 for use as FAX device.

@Cardinal 2400 MNP
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2&T5\C1\J0\N3\Q3\V1\K3&W^M
*Your Cardinal 2400 MNP modem is ready to go. You can set your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you.  MNP operation has also been enabled.

@Cermetek INFO-MATE 212A
1200

  XY
210
U 1^M^~C 0^M
D 'T
'^M
A
B
X
N
V
^M
DTR





0
0
1000
$You must open the case to set the switches.  Refer to your
$modem manual for this procedure.
$
$Switch settings:       1    2    3    4    5    6    7    8
$                       ON   OFF  OFF  ON   ON   OFF  ON   OFF
$
*Your Info-Mate 212A is ready to go.  Be sure to read your modem
*manual and double-check the setup.
*Note: Host mode operation is not supported at this time.

@Cermetek R/2400 SPC
2400


10
AT E1 Q0 V1 X4 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
$U D D U U D U D
$Your Cermetek modem is now configured for best performance
$
$An option might be to add M0 to the modem initial string to
$silence your modem if you prefer.
$
* Your modem is now ready to go

@Cermetek 1200 SPC
1200


10
AT E1 Q0 V1 X2 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
$U D D U U D U D
$Your Cermetek modem is now configured for best performance
$
$An option might be to add M0 to the modem initial string to
$silence your modem if you prefer.
$
* Your modem is now ready to go

@Codex 2264
19200


10
ATZ^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
500
^AT&FV1Q0
^AT&C1&D2*FL3*XC1*PT0&R0
^AT&W
* Your modem is now ready to go

@CompuCom Speedmodem STAR (V1.86)
38400


10
AT&F2*H1H0\T3%C0&D2&C1S7=55S10=10S11=50^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
*Your SpeedModem is ready to go.  You can set all of your dialing
*directory entries to 19200 baud and the modem will handle speed
*conversions for you.

@CTS Companion 212AH
1200


10
ATE1Q0V1S7=55S11=60S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
Disconnect
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@CTS Datacomm 2424ADH
2400


10
ATZ^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
^AT&FV1Q0
^AT^C1&D2S0=0S2=255S10=30X4
^AT&W
* Your modem is now ready to go

@DallasFax 14400 FAX/Modem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2X4W2S95=1\A3\J0\N3\Q3&W^M
*Your DallasFax is now configured.
*
*Set DTE speed to 19200 for use as FAX device.

@DallasFax 96/96 v.32
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$
^AT&F^M
^AT&C1&D2X4S95=1&K3S36=7&W^M
^AT&Q5S46=138S48=7&W^M
*Your DallasFax is now configured.

@Delta Gold DM 1200
1200


10
ATE1Q0V1X4 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Digicom 9624LE / 9624PC V.32bis
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT*F3*E9&W^M
*Your Digicom modem is ready to go.  You can set all of your
*dialing directory entries to 38400 baud and the modem will handle
*speed conversions for you.

@Digicom Scout 14400 v.32bis
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&C1&D2&R2*F3H0&W^M
*Your Scout is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@Digitan Hi*IQ ZX1896 2400 Fax Modem
2400


10
ATE1Q0V1X4&C1&D2S7=60S25=4^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
*Your 2400 baud modem is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@E*Tech Bullet PC2400MH MNP
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2&T5$C1$E2$F4$X1&W^M
*Your E*Tech 2400 MNP modem is ready to go.  You can set your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you.

@E*Tech Bullet E9696M V.32 MNP
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2&T5$C1$E1$F4$S0$X5&W^M
*Your E*Tech 9696M modem is ready to go.  You can set all of your
*dialing directory entries to 19200 baud and the modem will handle
*speed conversions for you.

@E*Tech Bullet E9696M V.42bis V.32 MNP
19200


10
AT&C1$F4$E3$C1$X4$S0&D2&S2&T0H0S0=0M0S12=0^M
AT$E3$C1S12=0M0DT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1$F4$E3$C1$X4$S0&D2&S2&T0H0S0=0M0S12=0&W^M
*Your E*Tech 9696M modem is ready to go.  You can set all of your
*dialing directory entries to 19200 baud and the modem will handle
*speed conversions for you.

@Everex 12e External (EV-936)
1200


10
ATE1F1H0M1Q0V1X4&C1&D2^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
^H
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
$ Switch Settings:  1   2   3   4   5   6   7   8   9
$                   On  Off Off Off Off On  Off Off Off
*Your Everex 12e (EV-936) is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Everex Evercom 24+ MNP
9600


10
AT\C0\J0\K5\N3\Q0\V1V1E1Q0X4^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^H
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
*Your Everex Evercom 24+ is ready to go.

@Everex 24e External (EV-945)
2400


10
ATE1F1H0M1Q0V1X4&C1&D2^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
^H
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
$ Switch Settings:  1   2   3   4   5   6   7   8   9
$                   On  Off Off Off Off On  Off Off Off
*Your Everex 24e (EV-945) is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Everex Evercom 24+ MNP
9600


10
AT\C0\J0\K5\N3\Q0\V1V1E1Q0X4^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
^H
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
*Your Everex Evercom 24+ is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Everex EverFax 24/96
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
NO ANSWER
^H
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&T5\J0\N3\V1\X1%C1\Q3&W
*Your Everex EverFax 24/96 is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Fastcomm FDX 2424 (MNP Class-5)
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$All switches on the bottom of the modem should be in the
$OPEN (off) position.
^AT&F^M
^ATE1Q0M1X4V1S7=60^M
^AT&B1&C1&D2&G0&H1&I1&M6&W^M
*Your FDX 2424 modem is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Fastcomm FDX 2496 Turbo
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$All switches on the bottom of the modem should be in the
$OPEN (off) position.
^AT&F^M
^ATE1Q0M1X4V1S7=60^M
^AT&B1&C1&D2&G0&H1&I1&M6&W^M
*Your FDX 2496 modem is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Fastcomm FDX 9696 (V.32 & MNP-5)
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$All switches on the bottom of the modem should be in the
$OPEN (off) position.
^AT&F^M
^ATE1Q0M1X4V1S7=60^M
^AT&B1&C1&D2&G0&H1&I1&M6&W^M
*Your FDX 9696 modem is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@FlashTalk LinePowered Mini Modem LP2400
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^ATB0E1L2M1Q0V1X4&C1&D2&G0&J0&L0&P0^M
^ATS0=0S2=43&W^M
*Your FlashTalk Linepowered Mini Modem LP2400 is now configured.

@Forval IM14400/SA14400 V.32bis (38400 baud)
38400


10
ATZ0^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^ATS25=0S7=60%E0\J0\N3\Q3&W^M
*Your Forval modem is ready to go.  You can set all of your
*dialing directory entries to 38400 baud and the modem will
*handle speed conversions for you.

@Forval IM14400/SA14400 V.32bis (57600 baud)
57600


10
ATZ0^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^ATS25=0S7=60%E0\J0\N3\Q3&W^M
*Your Forval modem is ready to go.  You can set all of your
*dialing directory entries to 57600 baud and the modem will
*handle speed conversions for you.

@Gateway 2000 TelePath FAX/Modem (v.32bis)
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^ATW1&C1&D2S95=44&W0^M
*Your Gateway 2000 TelePath FAX/Modem is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@Generic 1200 Baud Hayes clone
1200


10
ATE1Q0M1X1V1^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
$If your modem has hardware switches or jumpers, be sure to set
$the modem so that it does NOT force Carrier Detect (this is
$usually switch #6).  Also, set the DTR so that is NOT forced on
$all the time (this is usually switch #1).  If your modem uses
$NRAM to store the configuration, you should use the Generic
$1200 Baud (switchless) after this.
*Your 1200 baud modem is ready to go.  Be sure to read your modem
*manual and double-check the setup.

@Generic 1200 Baud Hayes clone (switchless)
1200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^ATE1Q0M1X1V1S7=60^M
^AT&C1&D2&W^M
*Your 1200 baud modem is ready to go.  Be sure to read your modem
*manual and double-check the setup.

@Generic 2400 baud Hayes clone
2400


10
ATE1Q0M1X1V1^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
$If your modem has hardware switches or jumpers, be sure to set
$the modem so that it does NOT force Carrier Detect (this is
$usually switch #6).  Also, set the DTR so that is NOT forced on
$all the time (this is usually switch #1).  If your modem uses
$NRAM to store the configuration, you should use the Generic
$2400 (switchless) after this.
*Your 2400 baud modem is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Generic 2400 Baud Hayes clone (switchless)
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^ATE1Q0M1X1V1S7=60^M
^AT&C1&D2&W^M
*Your 2400 baud modem is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Generic v.32 or v.32bis Hayes clone
19200


10
ATZ0^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$This will work with most v.32 and v.32bis modems.
^AT&F^M
^AT&C1&D2X3\J0\N3^M
*Your 9600 baud modem is ready to go.
*
*Set DTE speed to 19200 for use as FAX device if this modem has
*FAX capabilities.

@GVC 9600 V.42
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2%C1\J0\N3\Q3\V1&W^M
*Your GVC 9600  modem is ready to go.  You can set all of your
*dialing directory entries to 19200 baud and the modem will handle
*speed conversions for you.

@GVC 14400 v.32bis FAXmodem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT &F2&W
^AT &R0\G1&W
*Your GVC is ready to go
*
*Set DTE speed to 19200 for use as FAX device.

@GVC SM96 V.42bis
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F2&W^M
*Your GVC modem is ready to go.

@Hayes SmartModem 1200 External
1200


10
ATE1Q0M1X1V1S7=60^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
$ Switch Settings:    1  2  3  4  5  6  7  8  9  10
$                     U  U  D  U  D  U  U  D  U  U
$
$ Note:  Early versions did not have switches 9 & 10.
*Your Hayes SmartModem is ready to go.

@Hayes SmartModem 1200B Full Card Internal
1200


10
ATE1Q0M1X1V1S7=60^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
$ Hayes changed this version of the modem several times.
$ Be aware that your modem may or may not have all of these
$ switches or that these are the correct settings.  Only
$ your modem manual knows for sure...
$
$ Switch Settings: #2  DOWN - RJ12/RJ13 phone jack
$                      UP   - RJ11 or equivelent
$                  #3  UP   - Allow true CD
$                  #4  UP   - Allow DTR
$                      (early versions required strapping
$                       pins A-B for this function)
*Your SmartModem 1200B is ready to go.

@Hayes SmartModem 1200B Half Card Internal
1200


10
ATE1Q0M1X1V1S7=60^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
$ Switch Settings: #2  RIGHT - RJ12/RJ13 phone jack
$                      LEFT  - RJ11 or equivelent
$                  #3  RIGHT - Allow true CD
$                  #4  LEFT  - Allow DTR
*Your SmartModem 1200B is ready to go.

@Hayes SmartModem 2400
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^ATE1Q0M1X4V1S11=60^M
^AT&C1&D2&W^M
*Your SmartModem is ready to go.

@Hayes V-Series 2400 (without V.42)
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^ATE1Q0M1X4V1S11=60^M
^AT&C1&D2&G0&J0&K3&L0&P0^M
^AT&Q5&W^M
*Your V-Series SmartModem is ready to go.

@Hayes Personal Modem 2400
2400


10
AT&C1&D2E1Q0^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
*Your Hayes Personal Modem is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Hayes Ultra/Optima 14400
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^ATE1N1Q0M1X4V1W2^M
^AT&C1&D2&G0&J0&K3&L0&P0^M
^AT&Q5&U0^M
^ATS7=60&W^M
*Your ULTRA/OPTIMA 14400 is ready to go.

@Hayes Ultra/Optima 14400 FAX/modem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^ATE1N1Q0M1X4V1W2^M
^AT&C1&D2&G0&J0&K3&L0&P0^M
^AT&Q5&U0^M
^ATS7=60&W^M
*Your ULTRA/OPTIMA FAX is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@Hayes V-Series 9600
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
&M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^ATE1Q0M1X4V1S11=60^M
^AT&C1&D2&G0&J0&K3&L0&P0^M
^AT&Q5&W^M
*Your V-Series SmartModem is ready to go.

@Hayes V-Series 9600 V.42
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^ATE1Q0M1X4V1S11=60^M
^AT&C1&D2&G0&J0&K3&L0&P0^M
^AT&Q5S36=7S46=2S48=7W2&W^M
*Your V-Series SmartModem with V.42 is ready to go.

@Hayes V-series ULTRA Smartmodem 9600
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^ATE1N1Q0M1X4V1W2^M
^AT&C1&D2&G0&J0&K3&L0&P0^M
^AT&Q5&U0^M
^ATS7=60S49=8S50=240&W^M
*Your V-Series ULTRA is ready to go.

@IBM Model 5841 (1200)
1200


10
ATE1Q0V1S7=55S11=60S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE

^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@IBM PC 2400
2400


10
ATE1Q0V1X4&C1&D2 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@IBM PCjr Internal
300


10
^NF 4^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Incomm Midget 24FXI FAX/Modem
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT\J0\N3\Q3X4&W^M
*Your Incomm is ready to go.

@Infomate 212/A PC
1200


10
ATE1V1Q0 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Infomate 212/X PC
1200


10
ATE1Q0V1 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Intel 2400EX MNP
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&T5\J0\N3\Q3\V1\X1&W^M
*Your Intel 2400EX modem is ready to go.  You can set all of your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you.

@Intel 9600EX V.32 with V.42bis
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&T5&W^M
*Your Intel 9600EX modem is ready to go.  You can set all of your
*dialing directory entries to 38400 baud and the modem will handle
*speed conversions for you.

@Intel 14400EX V.32bis/V.42bis
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&T5&W^M
*Your Intel 14400EX modem is ready to go.

@Intel SatisFAXion
4800


10
ATZ0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
500
^AT&F
^AT \C1 S11=60
^AT&W0
* Your modem is now ready to go

@Intel SatisFaxion 400 FAX
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^ATS0=0&C1&D2V1Q0^M
^AT\J0\Q3\N3\A3\V1^M
^AT&T5&W^M
*Your Intel modem is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@InterQuad M2400E
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^ATE1Q0M1X4V1S11=60^M
^AT&C1&D2&W^M
*Your InterQuad Modem is ready to go.

@InterQuad M2400I
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^ATE1Q0M1X4V1S11=60^M
^AT&C1&D2&W^M
*Your InterQuad Modem is ready to go.

@LightCom 144F non-FAX mode
57600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&C1&D2S36=7S38=0S95=44^M
^ATS11=60&W^M
*Your LightCom 144F or 144/550 ready to go.

@LightCom 144F or 144/550
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&C1&D2S36=7S38=0S95=44^M
^ATS11=60&W^M
*Your LightCom 144F or 144/550 ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@LightCom 2400 Baud (All Models)
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^ATE1Q0M1X1V1S7=60^M
^AT&C1&D2&W^M
*Your LCOM 2400 baud modem is ready to go.

@LightCom 9600 Baud
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
1000
^AT&F^M
^AT&C1&D2S36=7S38=0S95=44^M
^ATS11=60&W^M
*Your LightCom 9600 V.32/V.42bis is ready to go.

@LightCom 96F or 96/550
LCom 96F or 96/550
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&C1&D2S36=7S38=0S95=44^M
^ATS11=60&W^M
*Your LightCom 96F or 96/550 ready to go.

@LightCom 144F or 144/550
57600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&C1&D2S36=7S38=0S95=44^M
^ATS11=60&W^M
*Your LightCom 144F or 144/550 ready to go.

@Maxmodem 2400/Fax 9600
2400


10
AT &C1 &D2^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE

^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Maxwell Modem 300/V
300


10
AT E1 Q0 V1 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE

^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Maxwell Modem 1200VP
1200


10
AT E1 Q0 V1 X4 &C1 &D2 S7=55 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Maxwell Modem 2400PC
2400


10
AT E1 Q0 V1 S7=30 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@MHz EasyTalk 1200
1200


10
AT E1 Q0 V1 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@MHz EasyTalk 2400
2400


10
AT E1Q0V1X4&C1&D2S7=55S11=60S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Microcom AX/1200,AX/1200c,AX/2400,AX/2400c
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$ Switch Settings:    FRONT 1 2 3 4 5 6 7 8 9 10
$                           U D D D D U U D U U
$
$                     REAR  1 2 3 4 5 6 7 8
$                           D D D U D U D D
^ATE1Q0M1X1V1\V1\E0\T0%E1%C1%P2%M0%Z1^M
^AT\G0\N3S0=0\J0\Q3\X0\K5\A3\C2%A13^M
^AT\L0\I0\H0&D2&C1\D0\R1&L0&M0&R0&T5^M
^AT&P0&G0B1&W^M
*Your modem is now configured for operation.  Be sure
*to set all your dialing directory entries to 9600 to get the
*best speed on all calls.

@Microcom AX/1200c AX/2400c MNP
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M^~^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$ Switch Settings:    FRONT 1 2 3 4 5 6 7 8
$                           U D D U D U U D
$
$                     REAR  1 2 3 4 5 6 7 8
$                           D U D U D U D U
^AT&F^M
^AT&C1&D2&T5\N3\J0\Q3&W^M
*Your Microcom modem is ready to go.

@Microcom AX/9624c  AX/9612c
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$ Switch Settings:    FRONT 1 2 3 4 5 6 7 8 9 10
$                           U D D D D U U D U U
$
$                     REAR  1 2 3 4 5 6 7 8
$                           D D D U D U D D
^ATE1Q0M1X1V1\V1\E0\T0%E1%C1%P2%M0%Z1^M
^AT\G0\N3S0=0\J0\Q3\X0\K5\A3\C2%A13^M
^AT\L0\I0\H0&D2&C1\D0\R1&L0&M0&R0&T5^M
^AT&P0&G0B1&W^M
*Your AX9624c is now configured for 19200 baud operation.  Be sure
*to set all your dialing directory entries to 19200 to get the
*best speed on all calls.

@Microcom QX/V.32c
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$ Switch Settings:    FRONT 1 2 3 4 5 6 7 8 9 10
$                           U D D U D U U D   U
$
$             0       REAR  1 2 3 4 5 6 7 8
$                           D U D U D D D D
^AT&F^M
^ATE1Q0X4\V1\N3\J0\Q3^M
^AT&D2&C1&T5%C3&W^M
*Your QX/V.32c is now configured for 38400 operation.  Be sure
*to set all your dialing directory entries to 38400 to get the
*best speed on all calls.

@Microcom QX/4232hs
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$ Switch Settings:    FRONT 1 2 3 4 5 6 7 8 9 10
$                           U D U U U D D D   U
$
$                     REAR  1 2 3 4 5 6 7 8
$                           D U D U D U U D
$
$                     T/D   in Data Mode
$                     O/A   your choice.
^AT&F^M
^ATE1Q0X4\V2\N5\J0\Q3^M
^AT&D2&C1&T5%C3&W^M
*Your QX/4232hs is now configured for 38400 operation.  Be sure
*to set all your dialing directory entries to 38400 to get the
*best speed on all calls.

@Multi-Tech MultiModem 224PC5
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
$Switch Settings on the Bottom of the modem:
$       Switch Bank 1 OPEN
$                   2 *
$                   3 *   *=Sets COM Port
$                   4 CLOSED
^AT&F^M
*Your 224PC5 is now configured for 2400 baud operation.  Be sure
*to read your modem manual and doublecheck the setup.

@Multi-Tech MultiModem 224EC / 224PC  W/MNP
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
$Switch Settings on the Bottom of the modem:
$       Switch Bank 1 OPEN
$                   2 *
$                   3 *   *=Sets COM Port
$
$       224EC:   Switches on Back of Edgecard
$                   1 OPEN (Up)
$                   2 OPEN (Up)
$                   3 CLOSED (Down)
$                   4 CLOSED (Down)
^AT&F^M
^AT&E1&E4&E15^M
^AT$MB2400$SB9600$BA0&W0^M
*Your 224EC/224PC is now configured for 9600 baud operation.  Be
*sure to set all your dialing directory entries to 9600 to get the
*best speed on all calls.

@Multi-Tech MultiModem MT224EH5 (MNP 5)
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
$Switch Settings on the Bottom of the modem:
$        4 Switch Bank 1 2 3 4
$                      D U D D
$        8 Switch Bank 1 2 3 4 5 6 7 8
$                      U U D U D U U D
$
$Jumpers that need to be changed -inside- the modem:
$  RTS:     toward the back of the modem.
$  CTS/RTS: toward the back of the modem.
^AT$A0&B0&BS0&C1$D0&D2$F1^M
^AT&G0$MI0&M0$R1&R1&S1^M
^ATB1E1M1Q0V1X4&Q0^M
^AT&E1&E4&E8&E10&E13&E15^M
^AT$MB2400$SB9600$BA0&W0^M
*Your 224EH5 is now configured for 9600 baud operation.  Be sure
*to set all your dialing directory entries to 9600 to get the
*best speed on all calls.

@Multi-Tech MultiModem MT224EH7 (MNP 7)
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
$Switch Settings on the Bottom of the modem:
$        4 Switch Bank 1 2 3 4
$                      D U D D
$        8 Switch Bank 1 2 3 4 5 6 7 8
$                      U U D U D U U D
$
$Jumpers that need to be changed -inside- the modem:
$  CTS/RTS: toward the back of the modem.
^AT$A0&B0&BS0&C1$D0&D2$F1^M
^AT&G0#L0$MI0&M0$R1&R1&S1^M
^ATB1E1M1Q0V1X4&Q0^M
^AT&E1&E4&E8&E10&E13&E15^M
^AT$MB2400$SB19200$BA0&W0^M
*The 224EH7 is now configured for 19200 baud operation.  Be sure
*to set all your dialing directory entries to 19200 to get the
*best speed on all calls.

@Multi-Tech MultiModem 696E
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
$Switch Settings on the Bottom of the modem:
$        4 Switch Bank 1 2 3 4
$                      D U D D
$        8 Switch Bank 1 2 3 4 5 6 7 8
$                      U U D U D U U D
$
$Jumpers that need to be changed -inside- the modem:
$  CTS/RTS: toward the back of the modem.
^AT$A1&B0&BS0&C1$D0&D2$EP1$F1^M
^AT&G0&M0$MI0&M0$R1&R1&S1^M
^ATB1E1M1Q0V1X4&Q0^M
^AT&E1&E4&E8&E10&E13&E15^M
^AT$MB9600$SB19200$BA0&W0^M
*The 696E is now configured for 19200 baud operation.  Be sure
*to set all your dialing directory entries to 19200 to get the
*best speed on all calls.

@Multi-Tech MultiModem 932EC
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
^AT&F^M
^AT&E1&E4&E8&E10&E13&E15^M
^AT$MB9600$SB19200$BA0&W0^M
*Your 932EC is now configured for 19200 baud operation.  Be sure
*to set all your dialing directory entries to 19200 to get the
*best speed on all calls.

@Multi-Tech MultiModem V.32
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
$Switch Settings on the Bottom of the modem:
$        4 Switch Bank 1 2 3 4
$                      D U D D
$        8 Switch Bank 1 2 3 4 5 6 7 8
$                      U U D U D U U D
$
$Jumpers that need to be changed -inside- the modem:
$   Open the case and move the jumper labeled
$   RTS/CTS so that the jumper it on the CTS side.
^AT&F^M
^AT&C1&D2B1E1M1Q0V1X4^M
^AT&E1&E4&E8&E10&E13&E15^M
^AT$MB9600$SB19200$BA0&W0^M
*Your V32 is now configured for 19200 baud operation.  Be sure
*to set all your dialing directory entries to 19200 to get the
*best speed on all calls.

@Multi-Tech MultiModem V32 with V.42bis
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
BUSY
VOICE

^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
$Switch Settings on the Bottom of the modem:
$        4 Switch Bank 1 2 3 4
$                      D U D D
$        8 Switch Bank 1 2 3 4 5 6 7 8
$                      U U D U D U U D
$
$Jumpers that need to be changed -inside- the modem:
$   Open the case and move the jumper labeled
$   RTS/CTS so that the jumper it on the CTS side.
^AT&F^M
^AT&C1&D2B1E1M1Q0V1X4^M
^AT&E1&E4&E8&E10&E13&E15^M
^AT$MB9600$SB38400$BA0&W0^M
*Your V32 is now configured for 38400 baud operation.  Be sure
*to set all your dialing directory entries to 38400 to get the
*best speed on all calls.

@Multi-Tech MultiModem II v.32bis
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
$Put switch 7 on the side of the modem UP.
$
$Here's how it should look:
$
$01 02 03 04 05 06 07 08 09 10 11 12   13 14 15 16
$UP UP DN UP UP UP UP DN DN UP DN DN   UP UP UP UP
$
$
$
^AT&F^M
^AT&C1&D2&E1&E4&E6&E15$BA0&W^M°°°°
^AT&W^M
^
*Your Multitech is now configured for high speed baud operation.

@Multi-Tech MultiModem II v.32bis FAX/modem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
600
$Put switch 7 on the side of the modem UP.
$
$Here's how it should look:
$
$01 02 03 04 05 06 07 08 09 10 11 12   13 14 15 16
$UP UP DN UP UP UP UP DN DN UP DN DN   UP UP UP UP
^AT&F^M
^AT&C1&D2&E1&E4&E6&E15$BA0&W^M°°°°
^AT&W^M
*Your Multitech is now configured for high speed baud operation.
*
*Set DTE speed to 19200 for use as FAX device.

@NEC 2431c
9600


10
ATZ^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
500
^AT&FV1Q0
^AT&C1&D2&E1S7=55S11=60
^AT&W
* Your modem is now ready to go

@NEC N9631 V.32 MNP
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F2^M
^ATE1Q0&T5\Q3\V1\X1*FT1&W^M
*Your NEC N9631 modem is ready to go.  You can set all of your
*dialing directory entries to 19200 baud and the modem will handle
*speed conversions for you.

@NEC N9635 V.32 MNP
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F2^M
^AT&C1&D2&W
^AT&T5\Q3\V1\J0\N3&W^M
*Your NEC N9631 modem is ready to go.

@Novation Professional 2400
2400


10
ATE1Q0V1X3YC0YF1YT0 S7=45 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Nuvotel 14,400IFX V42bis FAXmodem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0&K3\N3^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&C1&D2X4S0=0^M
^AT&K3\N3&W^M
*Your Nuvotel is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@OkiTel 1200
1200


10
ATE1Q0V1 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@OkiTel 2400
2400


10
ATE1Q0V1X4&C1&D2 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@OkiTel 2400 Plus
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$Switch Settings:
$
$   1   2   3   4   5   6
$   OFF OFF OFF OFF OFF ON
$
^AT&F^M
^AT&C1&D2%C0\J0\N3\Q3\V1S25=4&W^M
*Your OKITEL 2400 Plus is ready to go.  You can set all of your
*dialing directory entries to 9600 baud and the modem will handle
*speed conversions for you.

@OKITEL 9600 v.32
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$
$
$
$
^AT&F^M
^ATX3&C1&D2\J0\N3&K3^M
*Your OKI 9600 v.32 is ready to go.

@Pearl 1414 VE V.32bis V.42bis
57600


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$It's not necessary to put any switches. The program writes the con-
$figuration into the V-RAM. If you haven't installed a 16650 UART on
$your I/O card you should choose 38400 for reliable connects.
^AT&F^M
^ATB0N1Q0W1X4S7=60^M
^AT&C1&D2&K3&Q5&Y0^M
^ATS48=7S95=3&W0^M
*Now your Pearl modem (unbelieveable, but true) is configured. For
*getting the maximum out of, you should lock all your dial directories
*on 57600 baud.

@Pearl 1414 VE V.32bis V.42bis
57600


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
NO ANSWER
^M
DTR
RING
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$It's not necessary to put any switches. The program writes the con-
$figuration into the V-RAM. If you haven't installed a 16650 UART on
$your I/O card you should choose 38400 for reliable connects.
^AT&F^M
^ATB0N1Q0W1X4S7=60^M
^AT&C1&D2&K3&Q5&Y0^M
^ATS48=7S95=3&W0^M
*Now your Pearl modem (unbelieveable, but true) is configured. For
*getting the maximum out of, you should lock all your dial directories
*on 57600 baud.

@Penril Alliance V.32
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2\Q1,1&W^M
*Your Alliance V.32 modem is ready to go.  You can set all of your
*dialing directory entries to 19200 baud and the modem will handle
*speed conversions for you.

@Practical Peripherals PM1200
1200


10
ATE1Q0V1 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Practical Peripherals PM2400
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^ATB1E1L2M1Q0V1X4Y1&C1&D2&G0&J0&L0&P0^M
^AT&X0&Y0S0=0S2=43&W^M
*Your PM2400 is now configured.  Be sure to read your modem
*manual and double-check the setup.

@Practical Peripherals PM2400SA MNP
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^ATB1E1L2M1Q0V1X4Y0&C1&D2&J0&P0^M
^AT\A3\C1\E0\G0\J0\K5\N3\Q3\V1\X0^M
^AT%C0%A0S0=0S2=43&W0^M
*Your PM2400SA MNP is now configured.

@Practical Peripherals PM9600SA V.32
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^ATW2&C1&D2^M
*Your PM9600SA V.32 is now configured.

@Practical Peripherals PM14400FXSA FAXmodem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$Works best with ROM v1.12c or higher.  Type ATI3 to see which
$you have.
^AT&F^M
^ATW2&C1&D2X4&W^m
*Your PM14400FXSA V.32bis is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@Practical Peripherals PM14400FXSA non-FAX mode
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$Works best with ROM v1.12c or higher.  Type ATI3 to see which
$you have.
^AT&F^M
^ATW2&C1&D2X4&W^m
*Your PM14400FXSA V.32bis is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@Prometheus Pro 1200
1200


10
ATE1Q0V1 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Prometheus MCT-24I Half Card
2400


10
ATE1Q0V1X4&C1&D2 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Prometheus 9600
19200


10
AT&F^M~~~AT*F3^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
500
* Your modem is now ready to go

@Promethus Promodem 9600 Plus or EC
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$
$
$
$
$
$
^AT&F^M
^AT&C1&D2\Q3\N3\J0X1^M
*Your 9600 V.32 is now configured.

@QuickCom v.32
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$
^AT&F^M
^AT*E9*F3M0&C1S0=0*M2&W
*Your QuickCom v.32 is now configured.

@Quicktel Series 9600 V.32/V.42
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2\Q3^M
$ On the bottom of the modem, locate the 8-Position
$ DIP Switch.  Verify that switch #7 and #8 are set OFF.
$
$ Open the modem and locate the 4-Position DIP Switch.
$ Switch #1, #2 and #3 should be set OFF. Switch #4 should
$ be set ON.
*Your 9600 V.32 is now configured.  Be sure to read your modem
*manual and double-check the setup.  Also set all dialing
*directory entries to 19200 for maximum throughput.

@Racal Vadic Auto Dial VA212
1200


10
^M
^M^~^~D^M^~
^M
ON LINE
FAILED
VOICE
BUSY
NO DIAL TONE
^M
DTR





0
0
1000
^^E^M^~O^M
^1^M^~3^M^~
^1^M^~2^M^~
^16^M^~2^M^~
^17^M^~2^M^~
^19^M^~9^M^~
^^M
*Host Mode operation is not supported for the VA212 modem.  Be
*sure to read your modem manual and double-check the setup.

@Racal Milgo RMD 3221
9600


10
AT&F^M ATX9&C1&D2*F2 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
500
* Your modem is now ready to go

@Racal Vadic 1200 PA
1200


10
AT&F^M~~~AT &C1&D2^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Racal Vadic 2400 PS
2400


10
ATZ0^M~~~AT S7=55 S11=60^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
^AT&FV1Q0
^AT*F2&C1&D2*E1
^AT&W0
* Your modem is now ready to go

@Racal Vadic 2400 LC
2400


10
ATZ0^M~~~AT S7=55 S11=60^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
^AT&FV1Q0
^AT &C1&D2 *E1*F2*P1S7=55S11=60
^AT&W0
* Your modem is now ready to go

@Racal Vadic LC2400 PC
2400


10
ATZ^M~~~ATS7=55S11=60
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Racal Vadic 2400 PA Model 2
2400


10
ATZ^M~~~AT S7=55 S11=60^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
^AT&FV1Q0
^AT &C1&D2 X4 *E1*L1*Q1*F2*P1
^AT&W
* Your modem is now ready to go

@Racal Vadic 2400 VP
2400


10
ATZ^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
^AT&FV1Q0
^AT &C1*C1&D2*E1*F2Y1S7=55*Q1S11=60
^AT&W
* Your modem is now ready to go

@Racal Vadic 9600 PA
9600


10
ATZ^M~~~ATS7=55^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
500
^AT&FV1Q0
^AT&C1*C1&D2*F2Y1*Q1
^AT&W
* Your modem is now ready to go

@Supra Modem 2400
2400


10
ATE1Q0V1X4 &C1&D2 S7=55 S11=60 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIALTONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@Supra 14400 FAXmodem
19200


10
ATZ0^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0M1H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F2&W
*Your Supra is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@Supra 9600 FAXmodem
19200


10
ATZ0^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0M1H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F2&W
*Your Supra is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@Sysdyne MDM 24H
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0M1H0^M
ATA^M
OK
ATM0H1^M
0
1
750
$Switch settings should remain at factory defaults.  If you need
$to select a different COM port other than 2, refer to your
$owners manual for detailed instructions.
^ATB1E1F1L2M1Q0V1X4Y0^M
^AT&C1&D2S7=60S11=60&Y0&W0^M
*Your MDM 24H modem is ready to go.  Be sure to read your
*modem manual and double-check the setup.

@Telebit T1500
9600


10
ATZ^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
500
^AT&FV1Q0
^ATS51=4S0=0S52=1S131=1
^ATS58=2S66=1S68=2&W
* Your modem is now ready to go

@Telebit T2000 & Trailblazer Plus
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATH0^M^~ATS0=0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT E1 Q0 M1 V1 W1 X14 Y0 S0=0^M
^AT S50=0 S51=254 S52=4 S54=3 S58=2^M
^AT S63=1 S64=0 S66=1 S67=0 S68=2 S90=0^M
^AT S92=1 S94=1 S95=2 S96=1 S110=1^M
^AT S111=0 S131=1 S255=0 &W1 &W2^M
$This assumes the Telebit is in ECM (Enhanced Command Mode).
$To place your modem into ECM, follow these steps:
$
$  1. Start with the modem turned off and the A/B switch in the
$     A position.
$  2. Press and hold the T/D switch while turning on the modem.
$     Release the T/D switch -AFTER- the MR indicator comes on.
$
$This will store the ECM default settings in Profile A of non-
$volatile memory.
$
*Your Telebit is ready to go.  To get the most out of the dialing
*directory, be sure to set all phone book entries to 19200 baud.

@Telebit T2500
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
1500
^ATE1Q0M1X4V1S11=60^M
^AT&C1&D2&G0&J0&K3&L0&P0^M
^AT&Q5&W^M
$This assumes the Telebit is in CCM (Conventional Command Mode).
$To place your modem into CCM, follow these steps:
$
$  1. Turn the modem off.
$  2. Hold in the T/D switch and turn the power on.  Release the
$     switch when the PEP,CD and MR lights are flashing.  Ignore
$     any other lights that may be lit from here on.
$  3. Tap the T/D switch until just the CD light is lit (not
$     flashing).  The PEP and MR lights are OFF.
$  4. Press and hold the T/D switch (2 seconds or more) until the
$     CD light is flashing again.
$
$              >> Do these steps before proceeding! <<
*Your Telebit is ready to go.  To get the most out of the dialing
*directory, be sure to set all phone book entries to 19200 baud.

@Telebit T3000
38400


10
ATZ0^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1500
^AT&F9^M
^
^
*Your Telebit is ready to go.
*Be sure to specify this device for each of your dialing
*directory entries.  Also double check the configuration with
*your modem's documentation.

@Toshiba T24D/X w/o error correction
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^AT&F^M
^AT&C1&D2X4&K0W1\N0&W
*Your Toshiba 2400 baud modem is ready to go.
*Error correction disabled for compatibility with older modems.

@Toshiba T24D/X with error correction
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&C1&D2X4&K3W1\N3&W
*Your Toshiba 2400 baud modem is ready to go.

@TwinCom 14400
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2\A3&T5S95=3&W
*Your Twincom is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@TwinCom 96/42i
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^ATX4&C1&D2&Q5N1W2&W^M
*Your Twincom is ready to go.  You can set all of your
*dialing directory entries to 38400 baud and the modem will handle
*speed conversions for you.

@UDS Fast Talk 2400
2400


10
ATE1Q0V1X4&C1&D2 S7=55 S0=0^M
ATDT
^M
CONNECT
NO CARRIER
BUSY
VOICE
NO DIAL TONE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
* Your modem is now ready to go

@UDS 2440
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^ATS7=60^M
^AT&C1&D2&R&T5%N8%U3%V0%K1&W^M
$There are two jumpers inside that need to be verified.  The CTS
$and RTS flow control.                      ___
$The pins are marked like this:  o o|     o o o
$                                o o|   FLO   CTS
$                                F R
$                                L T
$                                O S
$
$ Make sure the pins above RTS are jumpered, and that the right two
$ by the CTS are covered.  Put the case back together and continue.
*Your UDS modem is ready to go.  To get the most out of it,
*be sure to set all your dialing directory entries to 9600 baud.

@UDS V.3224/V.3225 (V.32)
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^ATS7=60^M
^AT&C1&D2&R&T5%C1\Q3\V1&W^M
*Your UDS modem is ready to go.  To get the most out of it,
*be sure to set all your dialing directory entries to 19200 baud.

@USRobotics Direct 1200PC Internal
1200


10
ATE1Q0M1X1V1S7=60^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~
RING^M^J
~~~+++~~~ATS0=0^M
ATA^M
OK
ATM0^M
0
1
500
$External Switchblock:
$
$      1   2   3   4
$      OFF OFF OFF OFF
$
$Jumpers:
$
$      J1  UP
$      J2  UP
$      J3  DOWN
$      J14 UP
$
*Your Direct 1200PC is now configured.

@USRobotics Password 1200 Internal
1200


10
ATE1Q0M1X1V1S7=60^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~
RING^M^J
~~~+++~~~ATS0=0^M
ATA^M
OK
ATM0^M
0
1
500
$External Switchblock:
$
$      1   2   3   4
$      UP  UP  UP  UP
$
$Jumpers:
$
$      J1  UP
$      J2  UP
$      J3  RIGHT
$      J5  DOWN
$
*Your Password is now configured.

@USRobotics Direct 2400PC / Sportster 2400
2400


10
ATE1Q0M1X6V1S7=60S11=60^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
$External Switchblock:
$
$      1   2   3   4   5   6   7   8   9   10
$      OFF OFF ON  OFF ON  OFF OFF ON  ON  ON
$
*Your Courier is now configured.

@USRobotics MicroLink 2400
2400


10
ATE1Q0M1X6V1S7=60S11=60^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
$External Switchblock:
$
$      1   2   3   4   5   6   7   8   9   10
$      OFF OFF ON  OFF ON  OFF OFF ON  ON  ON
$
*Your Courier is now configured.

@USRobotics VARmodem 2400
2400


10
ATE1Q0M1X6V1S7=60S11=60^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
0
500
$External Switchblock:
$
$      1   2   3   4   5   6   7   8   9   10
$      OFF OFF ON  OFF ON  OFF OFF ON  ON  ON
$
*Your VARmodem is now configured.

@USRobotics Courier 2400e and 2400PC w/MNP
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
1
1000
$External Switchblock:   1  2  3  4  5  6  7  8  9  10
$                        U  U  D  U  D  U  U  D  D  U
$
$                        Where U is UP  and  D is DOWN
$
$Note: for the 2400PC, turn the modem on it's side so
$      you can read the numbers, then the above settings
$      will make sense.
%AT&FE0^M
^ATE1Q0M1X6V1S7=60S11=60^M
^AT&B0&H1&R2&I0&M4&N0&W^M
*Your Courier is now configured.  Consult your modem
*manual for additional setup parameters if you wish to take
*advantage of speeds higher than 2400 when using MNP.

@USRobotics HST (96x ROM)
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^ATE1Q0M1V1X7S7=60^M
^AT&B1&H1&M4&N0&R2&W^M
*Your Courier HST is now configured.  To get the most out of it,
*be sure to set all your dialing directory entries to 19200 baud.

@USRobotics HST (144x ROM)
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^ATE1Q0M1X7V1S7=60^M
^AT&B1&C1&D2&H1&M4&N0&R2&W^M
*Your Courier HST is now configured.  To get the most out of it,
*be sure to set all your dialing directory entries to 19200 baud.

@USRobotics HST Dual Standard
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^AT&F^M
^ATB1E1Q0M1X7V1S7=60^M
^AT&A2&B1&C1&D2&H1&R2&M4&N0&K0&W^M
*Your Courier HST Dual Standard is now configured so that either
*V.32 or HST calls will be answered.  To get the most out of it,
*be sure to set all your dialing directory entries to 38400 baud.

@USRobotics HST (144x ROM) (V.42)
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^ATE1Q0M1X7V1S7=60^M
^AT&A3&K3&B1&C1&D2&H1&M4&N0&R2&W^M
*Your Courier HST is now configured.  To get the most out of it,
*be sure to set all your dialing directory entries to 38400 baud.

@USRobotics HST Dual Standard (V.42)
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^AT&F^M
^ATB1E1Q0M1X7V1S7=60^M
^AT&A3&B1&C1&D2&H1&R2&M4&N0&K3&W^M
*Your Courier HST Dual Standard is now configured so that either
*V.32 or HST calls will be answered.  To get the most out of it,
*be sure to set all your dialing directory entries to 38400 baud.

@USRobotics HST with V.32bis (Duals too)
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^AT&F^M
^ATE1Q0M1X7V1S7=60^M
^AT&A3&K3&B1&C1&D2&H1&M4&N0&R2&W^M
*Your Courier HST is now configured.  To get the most out of it,
*be sure to set all your dialing directory entries to 38400 baud.

@USRobotics 16800 Dual Standard w/FAX
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^AT&F^M
^ATE1Q0M1X7V1S7=60S11=40^M
^AT&A3&K3&B1&C1&D2&H1&M4&N0&R2&W^M
*Your USR is now configured.

@USRobotics 16800 HST or Dual Standard
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^AT&F^M
^ATE1Q0M1X7V1S7=60S11=40^M
^AT&A3&K3&B1&C1&D2&H1&M4&N0&R2&W^M
*Your USR is now configured.

@USRobotics Sportster 14400
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^AT&F^M
^ATE1Q0M1X7V1S7=60^M
^AT&A3&K3&B1&C1&D2&H1&M4&N0&R2&W^M
*Your Sportster is now configured.
*
*Set DTE speed to 19200 for use as FAX device.

@USRobotics Sportster 14400 FAX/modem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock: 1-UP  2-UP  3-DOWN  4-UP     5-DOWN
$                      6-UP  7-UP  8-DOWN  9-DOWN  10-UP
$                      WIDE SWITCH-UP
^AT&F^M
^ATE1Q0M1X7V1S7=60^M
^AT&A3&K3&B1&C1&D2&H1&M4&N0&R2&W^M
*Your Sportster is now configured.
*
*Set DTE speed to 19200 for use as FAX device.

@USRobotics Sportster 9600 v.32
38400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
$External switchblock: 1-UP   2-UP  3-DOWN  4-UP
$                      5-DOWN 6-UP  7-UP    8-DOWN
$
^AT&F&W
^AT&B1&H1&R2&K1&M4&W
^ATB0X3S6=1S11=45&W
*Your USR Sportster is now configured.

@Ven-Tel 2400 Half Card (4 Option Switches)
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
$Internal switchblock:
$
$   Refer to your manual for setting the COM port via
$   these switches.  This is set with switches 3 and 4.
^ATE1M1Q0X4V1&C1&D2&Y0S0=0&W^M
*Your Vel-Tel 2400 Half Card is now configured.

@Ven-Tel 2400 Half Card (6 Option Switches)
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
500
$Internal switchblock:
$
$      1  2  3  4  5  6
$      O  C  *  *  O  *
$
$   Where  O = OPEN,  C = CLOSED
$          * = Dependent on hardware.  See manual.
$
^ATE1M1Q0X4V1S0=0^M
*Your Vel-Tel 2400 Half Card is now configured.

@Ven-Tel 2400-33
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$External switchblock:
$         1-OFF  2-OFF  3-OFF  4-OFF   5-OFF
$         6-OFF  7-ON   8-ON   9-ON   10-OFF
^AT%A13B1\C1&C1\D3&D2E1F1\G0&G0^M
^AT&L0M1&M0\N3Q0\Q3&R1\T0&T4V1^M
^AT\V1X4\X1Y0&W^M
*Your Vel-Tel 2400-33 is now configured.  To get the most out of
*it, be sure to set all your dialing directory entries to 9600
*baud.

@Ven-Tel Pathfinder 18K
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT X3 S0=0^M
^AT S51=5 S54=3 S58=2^M
^AT S66=1 S68=2 S92=1 S95=2^M
^AT S111=0 &W^M
*Your Pathfinder is ready to go.  To get the most out of the dialing
*directory, be sure to set all phone book entries to 19200 baud.

@ViVa 24m  2400 baud MNP-5
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT&C1&D2%C0\J0\N3\Q3\V1S25=4&W^M
*Your ViVa 24m is ready to go.  You can set all of your
*dialing directory entries to 9600 baud and the modem will
*handle speed conversions for you.

@Yoriko 9600/14400/Fax
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
^AT&F^M
^AT &C1 &D2 W2 &K3 S37=70 S11=50 S95=3 &W^M
*Your Yoriko modem is ready to go.  You can set all of your
*dialing directory entries to 19200 baud and the modem will
*handle speed conversions for you.

@Zoltrix 14400 FAX/modem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT\J0\Q3\N3\V0&W^M
*Your ZOLTRIX is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@Zoltrix 9600 FAX/modem
19200


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^ATC1&D2\N3&K3S95=3&W^M
*Your ZOLTRIX is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@ZOOM/Modem HC2400R
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^AT&F^M
^ATS11=60&C1&D2&W^M
*Your Zoom HC2400R is ready to go.

@ZOOM/Modem MX2400R
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^AT&F^M
^ATS11=60&C1&D2&W^M
*Your Zoom MX2400R is ready to go.

@ZOOM/Modem HC2400S (SendFax)
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^AT&F^M
^ATS11=60&C1&D2&W^M
*Your Zoom HC2400S is ready to go.

@ZOOM/Modem MX2400S (SendFax)
2400


10
ATZ^M
ATDT
^M
CONNECT
NO DIALTONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
0
1
1000
^AT&F^M
^ATS11=60&C1&D2&W^M
*Your Zoom MX2400S is ready to go.

@ZOOM/Modem V.42bis (2400 baud)
9600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
~~~+++~~~ATH0^M
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^AT&F^M
^AT&C1&D2S36=7S38=0S95=44^M
^ATS11=60&W^M
*Your Zoom HC2400R V.42bis is ready to go.

@ZOOM/Modem 14400 FAX/modem
19200


10

ATDT
^M
CONNECT
NO DIAL
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
1000
^ATV1W2\N3^M
^AT&C1&D2&K3&Q5&R0&W^M
*Your Zoom V.32 is ready to go.
*
*Set DTE speed to 19200 for use as FAX device.

@ZyXEL U-1496, U-1496B, U-1496E V.32bis V.42bis
57600


10
ATZ^M
ATDT
^M
CONNECT
NO DIAL TONE
NO CARRIER
BUSY
VOICE
^M
DTR
RING^M^J
ATS0=0H0^M
ATA^M
OK
ATM0H1^M
1
0
500
$There is no switch to set, just let the program to write the
$setting to V-RAM.  If you do not have 16650 UART installed in
$your I/O card, please use 38400 baud for reliable operation.
^AT&F^M
^ATQ0M1X6V1S7=60^M
^AT&K4&B1&C1&D2&H3*E0&N0&W^M
*Your ZyXEL is now configured.  To get the most out of it,
*be sure to set all your dialing directory entries to 57600 baud.

............................ END OF FILE ..............................