home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
PC World 1997 November
/
PCWorld_1997-11_cd.bin
/
hardware
/
ovladace
/
Sit
/
3com
/
edisk
/
3c59xn.exe
/
NDIS
/
LANSRV.TXT
< prev
next >
Wrap
Text File
|
1995-09-22
|
3KB
|
133 lines
3Com (R) Corporation
NDIS 2.01 Drivers Installation Notes
IBM LAN Server v4.0 for OS/2
============================
This procedure describes how to install the NDIS driver
for LAN Server 4.0. OS/2 must be already installed on
your computer. To install the NDIS driver for the 3Com
EtherLink III Family adapter, follow these steps:
1. Open an OS/2 prompt.
2. Insert the LAN Server MPTS (Multi-Protocol Transport
Services) disk 1 in your floppy drive.
3. Make that drive your current drive. Type:
A: [Enter]
4. Type:
Install [Enter]
5. Select OK.
6. Select Install.
7. Select a target drive and then choose OK.
The default drive is C.
8. Insert disk 2 when prompted and select OK.
9. Select OK when the MPTS installation is complete.
10. Select Configure.
11. Select LAN Adapters and Protocols
and then choose Configure.
12. Select Other Adapters and then choose OK.
13. Insert the 3Com EtherDisk diskette in the
floppy drive and enter the drive letter and path to
the 3Com NDIS drivers. For example, type:
A:\NDIS\OS2
14. Select OK.
15. Select 3Com Fast Etherlink/EtherLink III Bus Master family adapter
for OS/2 and then choose Add.
16. Under Current Configuration, select 3Com Fast Etherlink/
EtherLink III Bus Master adapter for OS/2 and then choose
Edit.
17. Enter the 12-digit address of your 3Com Fast EtherLink/Etherlink
III Bus Master Family adapter and then choose OK.
The address is found on the 3Com Fast Etherlink/EtherLink III Bus Master
family adapter following the characters EA=.
18. Select the protocol(s) you will be using with
your network and then choose Add.
19. Select your protocol(s) under Current
Configuration and then choose Edit.
20. Enter the 12-digit address of your 3Com Fast EtherLink/Etherlink
III Bus Master Family adapter and then choose OK.
21. Select OK.
22. Select Close.
23. Select Exit.
24. Select Update CONFIG.SYS and choose Exit.
25. Select OK.
26. Select Exit.
27. Quit OS/2 and reboot for the changes to take effect.
28. Follow the IBM instructions on installing
LAN Server to complete the installation.
IBM LAN Server v4.0 for DOS
===========================
IBM DOS Lan Services Install v4.0
1. Insert the disk labeled DOS LAN Services Disk 1 into
your disk drive.
2. Change to that drive and type:
INSTALL
3. Choose the directory where you want the software installed.
The default is C:\NET.
4. A menu appears that provides a list of network cards.
Choose "Network card not shown in the list below..."
5. Type:
A:\NDIS\DOS and remove the DOS LAN Services Disk 1
diskette and insert the Etherdisk diskette.
6. The next menu should display 3Com Fast EtherLink/Etherlink EtherLink III
Bus Master Family.
7. Additional menus will appear. Choose the appropriate options
for your network environment. Refer to the IBM manual if
there are questions regarding these menus.
8. After completing the installation, you must copy EL59X.DOS
to C:\NET before rebooting.
=========================================================
(%VER NDIS - IBM LAN Server v3.4c)