1000 The file %1 needs to be modified. The file will be backed up as %2.\n\nDo you want TCP/IP Stack Configuration to modify the file for you?
1001 TCP/IP Stack Configuration could not modify the file %s. You need to manually edit the file for the applications to run properly.
1002 Use broadcast (b-node)
1003 Do you want to delete the selected table entry?
1004 Do you want to delete the selected table entries?
1005 Duplicate aliases not allowed.
1006 An entry needs to be selected from the table, for this operation.
1007 Do you want to save changes to the configuration file?
1008 Another installed LAN interface is already enabled. Currently, only one LAN interface can be enabled at a time.\n\nDo you want to enable this interface?
1009 Error opening host table file:
1010 Please specify the correct absolute file name of the %1 file.
1011 Write access not available for the configuration file %1. TCP/IP Stack Configuration is unable to save the configuration information.
1012 Read access not available for the configuration file %1. TCP/IP Stack Configuration is unable to read the existing configuration information.
1013 A Subnet Mask value was not entered. A default value of %1 was derived from the IP Address. Do you want to accept the default?
1014 TCP/IP Stack Configuration could not detect the presence of an %1 driver in memory. The active interface will not work without this driver.\n\nDo you want to install an %2 driver now?
1015 Use WINS (p-node)
1016 The %1 file has not been installed. The network driver will not work without this file. Do you want to quit this dialog?
1017 Use broadcasts first, then WINS (m-node)
1018 Use WINS first, then broadcasts (h-node)
1030 No Interface is enabled.
1031 The PC Host Name has not been specified.
1032 The Domain Name has not been specified.
1033 The Subnet Mask value is not valid.
1034 The Interface Address is not a valid IP address.
1035 The Broadcast Address is not a valid IP address.
1036 The Destination Address is not a valid IP address.
1037 The Gateway Address is not a valid IP address.
1038 The Host Address is not a valid IP address.
1039 The DNS address is not a valid IP Address.
1040 Please specify a valid IP Address for the Default Route.
1042 The PC Host Name entry contains the domain name.
1043 The Ethernet Address is not valid.
1044 No Host Name has been specified for this entry.
1045 The host name should not contain embedded spaces.
1060 HostAddress
1061 EthernetAddress
1062 Translation
1063 NameServer_
1064 Name
1065 Type
1066 IPAddress
1067 NetMask
1068 BroadcastAddress
1069 Enabled
1071 DestinationAddress
1072 GatewayAddress
1073 AddressQualifier
1074 Adapter
1075 HostName
1076 LocalDomain
1077 Directory
1078 HostInfo
1079 HostAliases
1080 DefaultGateway
1081 DefaultMetric
1082 RIPListen
1083 RouterDiscovery
1084 SearchOrder
1085 UserName
1086 EnableDHCP
1087 PreviousDefaultGateway
1088 HostFile
1089 Timezone
1090 COM_Port
1091 Speed
1092 StopBits
1093 FlowControl
1094 CarrierDetect
1097 descLn0
1098 descLn1
1099 Visible
1100 Animation
1104 Maximum number of routes has been reached.
1200 TGVMultinet
1201 ARP
1202 InterFace
1203 Route
1204 DomainNameResolver
1205 MultiNet
1206 ConfigurationFiles
1207 Routing
1208 Network Drivers
1209 CheetahIcon
1210 IPForwarding
1211 TDI
1230 Host
1231 Network
1232 Proxy
1233 Publish
1234 Proxy,Publish
1235 Ethernet
1236 SLIP
1237 PPP
1238 Token-Ring
1239 Confirm Deletion
1240 TCP/IP Stack Configuration
1241 Fatal Error!
1242 FDDI
1245 Not Specified
1246 Hardware
1247 None
1248 HOSTS
1249 HOSTINFO.CNF
1250 HSTALIAS.CNF
1251 SYSTEM.INI
1254 Host Table then DNS
1255 DNS then Host Table
1256 DNS only
1257 Host Table only
1258 The following error(s) were detected in your configuration:
1259 The protocol stack has not been configured correctly. Do you want to quit TCP/IP Stack Configuration?
1261 network.setup
1262 netcard
1263 Form Validation Error Message
1264 The following entry/entries in this form are invalid:
1265 110,4400,6000,8400,9200,9600,14400,19200
1266 COM 1,COM 2,COM 3,COM 4
1267 The protocol stack has not been configured correctly. Do you want to save changes to the configuration file?
1269 Serial
1420 New Interface
1421 Modify Interface
1422 New Host
1423 Modify Host
1424 New DNS Server IP Address
1425 Modify DNS Server IP Address
1426 New Route
1427 Modify Route
1428 New ARP Table Entry
1429 Modify ARP Table Entry
1446 Configuration of the active interface is not complete. The TCP/IP stack may not operate properly.
1450 The data in the configuration file, pertaining to the active interface, is inconsistent with the corresponding entry in SYSTEM.INI. Please check the configuration of the active interface.
1451 &About TCP/IP Stack Configuration...
1452 FileDescription
1453 File Version:
1454 FileVersion
1455 LegalCopyright
1456 The stack currently supports only %1 enabled SLIP Interfaces.
1457 &Version Information...
1458 Token Ring
1460 RIPDefaultOnly
1461 Cannot open HOSTS file
1462 TDI cannot be enabled during installation. To enable TDI, finish installing then run the configuration utility and enable it.
1463 The installation procedure has noticed that TDI is currently enabled. It will be disabled after the installation is complete. To re-enable, run the configuration utility after the installation is complete.
