1000	The file %1 needs to be modified. The file will be backed up as %2.\n\nDo you want TCP/IP Stack Configuration to modify the file for you?
1001	TCP/IP Stack Configuration could not modify the file %s. You need to manually edit the file for the applications to run properly.
1002	Use broadcast (b-node)
1003	Do you want to delete the selected table entry?
1004	Do you want to delete the selected table entries?
1005	Duplicate aliases not allowed.
1006	An entry needs to be selected from the table, for this operation.
1007	Do you want to save changes to the configuration file?
1008	Another installed LAN interface is already enabled. Currently, only one LAN interface can be enabled at a time.\n\nDo you want to enable this interface?
1009	Error opening host table file: 
1010	Please specify the correct absolute file name of the %1 file.
1011	Write access not available for the configuration file %1. TCP/IP Stack Configuration is unable to save the configuration information.
1012	Read access not available for the configuration file %1. TCP/IP Stack Configuration is unable to read the existing configuration information.
1013	A Subnet Mask value was not entered. A default value of %1 was derived from the IP Address. Do you want to accept the default?
1014	TCP/IP Stack Configuration could not detect the presence of an %1 driver in memory. The active interface will not work without this driver.\n\nDo you want to install an %2 driver now?
1015	Use WINS (p-node)
1016	The %1 file has not been installed. The network driver will not work without this file. Do you want to quit this dialog?
1017	Use broadcasts first, then WINS (m-node)
1018	Use WINS first, then broadcasts  (h-node)
1030	No Interface is enabled.
1031	The PC Host Name has not been specified.
1032	The Domain Name has not been specified.
1033	The Subnet Mask value is not valid.
1034	The Interface Address is not a valid IP address.
1035	The Broadcast Address is not a valid IP address.
1036	The Destination Address is not a valid IP address.
1037	The Gateway Address is not a valid IP address.
1038	The Host Address is not a valid IP address.
1039	The DNS address is not a valid IP Address.
1040	Please specify a valid IP Address for the Default Route.
1042	The PC Host Name entry contains the domain name.
1043	The Ethernet Address is not valid.
1044	No Host Name has been specified for this entry.
1045	The host name should not contain embedded spaces.
1060	HostAddress
1061	EthernetAddress
1062	Translation
1063	NameServer_
1064	Name
1065	Type
1066	IPAddress
1067	NetMask
1068	BroadcastAddress
1069	Enabled
1071	DestinationAddress
1072	GatewayAddress
1073	AddressQualifier
1074	Adapter
1075	HostName
1076	LocalDomain
1077	Directory
1078	HostInfo
1079	HostAliases
1080	DefaultGateway
1081	DefaultMetric
1082	RIPListen
1083	RouterDiscovery
1084	SearchOrder
1085	UserName
1086	EnableDHCP
1087	PreviousDefaultGateway
1088	HostFile
1089	Timezone
1090	COM_Port
1091	Speed
1092	StopBits
1093	FlowControl
1094	CarrierDetect
1097	descLn0
1098	descLn1
1099	Visible
1100	Animation
1104	Maximum number of routes has been reached.
1200	TGVMultinet
1201	ARP 
1202	InterFace 
1203	Route 
1204	DomainNameResolver
1205	MultiNet
1206	ConfigurationFiles
1207	Routing
1208	Network Drivers
1209	CheetahIcon
1210	IPForwarding
1211	TDI
1230	Host
1231	Network
1232	Proxy
1233	Publish
1234	Proxy,Publish
1235	Ethernet
1236	SLIP
1237	PPP
1238	Token-Ring
1239	Confirm Deletion
1240	TCP/IP Stack Configuration
1241	Fatal Error!
1242	FDDI
1245	Not Specified
1246	Hardware
1247	None
1248	HOSTS
1249	HOSTINFO.CNF
1250	HSTALIAS.CNF
1251	SYSTEM.INI
1254	Host Table then DNS
1255	DNS then Host Table
1256	DNS only
1257	Host Table only
1258	The following error(s) were detected in your configuration:
1259	The protocol stack has not been configured correctly. Do you want to quit TCP/IP Stack Configuration?
1261	network.setup
1262	netcard
1263	Form Validation Error Message
1264	The following entry/entries in this form are invalid:
1265	110,4400,6000,8400,9200,9600,14400,19200
1266	COM 1,COM 2,COM 3,COM 4
1267	The protocol stack has not been configured correctly. Do you want to save changes to the configuration file?
1269	Serial
1420	New Interface
1421	Modify Interface
1422	New Host
1423	Modify Host
1424	New DNS Server IP Address
1425	Modify DNS Server IP Address
1426	New Route
1427	Modify Route
1428	New ARP Table Entry
1429	Modify ARP Table Entry
1446	Configuration of the active interface is not complete. The TCP/IP stack may not operate properly.
1450	The data in the configuration file, pertaining to the active interface, is inconsistent with the corresponding entry in SYSTEM.INI. Please check the configuration of the active interface.
1451	&About TCP/IP Stack Configuration...
1452	FileDescription
1453	    File Version: 
1454	FileVersion
1455	LegalCopyright
1456	The stack currently supports only %1 enabled SLIP Interfaces.
1457	&Version Information...
1458	Token Ring
1460	RIPDefaultOnly
1461	Cannot open HOSTS file
1462	TDI cannot be enabled during installation. To enable TDI, finish installing then run the configuration utility and enable it.
1463	The installation procedure has noticed that TDI is currently enabled. It will be disabled after the installation is complete. To re-enable, run the configuration utility after the installation is complete.