OpenStep 4.2J (Developer)

home *** CD-ROM | disk | FTP | other *** search

/ OpenStep 4.2J (Developer) / os42jdev.iso / NextDeveloper / Source / GNU / gcc / gcc.info-14 < prev next >

Wrap

GNU Info File | 1995-11-26 | 40.0 KB | 971 lines

This is Info file gcc.info, produced by Makeinfo-1.55 from the input file gcc.texi. This file documents the use and the internals of the GNU compiler. Published by the Free Software Foundation 59 Temple Place - Suite 330 Boston, MA 02111-1307 USA Copyright (C) 1988, 1989, 1992, 1993, 1994, 1995 Free Software Foundation, Inc. Permission is granted to make and distribute verbatim copies of this manual provided the copyright notice and this permission notice are preserved on all copies. Permission is granted to copy and distribute modified versions of this manual under the conditions for verbatim copying, provided also that the sections entitled "GNU General Public License," "Funding for Free Software," and "Protect Your Freedom--Fight `Look And Feel'" are included exactly as in the original, and provided that the entire resulting derived work is distributed under the terms of a permission notice identical to this one. Permission is granted to copy and distribute translations of this manual into another language, under the above conditions for modified versions, except that the sections entitled "GNU General Public License," "Funding for Free Software," and "Protect Your Freedom--Fight `Look And Feel'", and this permission notice, may be included in translations approved by the Free Software Foundation instead of in the original English. File: gcc.info, Node: Machine Modes, Next: Constants, Prev: Flags, Up: RTL Machine Modes ============= A machine mode describes a size of data object and the representation used for it. In the C code, machine modes are represented by an enumeration type, `enum machine_mode', defined in `machmode.def'. Each RTL expression has room for a machine mode and so do certain kinds of tree expressions (declarations and types, to be precise). In debugging dumps and machine descriptions, the machine mode of an RTL expression is written after the expression code with a colon to separate them. The letters `mode' which appear at the end of each machine mode name are omitted. For example, `(reg:SI 38)' is a `reg' expression with machine mode `SImode'. If the mode is `VOIDmode', it is not written at all. Here is a table of machine modes. The term "byte" below refers to an object of `BITS_PER_UNIT' bits (*note Storage Layout::.). `QImode' "Quarter-Integer" mode represents a single byte treated as an integer. `HImode' "Half-Integer" mode represents a two-byte integer. `PSImode' "Partial Single Integer" mode represents an integer which occupies four bytes but which doesn't really use all four. On some machines, this is the right mode to use for pointers. `SImode' "Single Integer" mode represents a four-byte integer. `PDImode' "Partial Double Integer" mode represents an integer which occupies eight bytes but which doesn't really use all eight. On some machines, this is the right mode to use for certain pointers. `DImode' "Double Integer" mode represents an eight-byte integer. `TImode' "Tetra Integer" (?) mode represents a sixteen-byte integer. `SFmode' "Single Floating" mode represents a single-precision (four byte) floating point number. `DFmode' "Double Floating" mode represents a double-precision (eight byte) floating point number. `XFmode' "Extended Floating" mode represents a triple-precision (twelve byte) floating point number. This mode is used for IEEE extended floating point. On some systems not all bits within these bytes will actually be used. `TFmode' "Tetra Floating" mode represents a quadruple-precision (sixteen byte) floating point number. `CCmode' "Condition Code" mode represents the value of a condition code, which is a machine-specific set of bits used to represent the result of a comparison operation. Other machine-specific modes may also be used for the condition code. These modes are not used on machines that use `cc0' (see *note Condition Code::.). `BLKmode' "Block" mode represents values that are aggregates to which none of the other modes apply. In RTL, only memory references can have this mode, and only if they appear in string-move or vector instructions. On machines which have no such instructions, `BLKmode' will not appear in RTL. `VOIDmode' Void mode means the absence of a mode or an unspecified mode. For example, RTL expressions of code `const_int' have mode `VOIDmode' because they can be taken to have whatever mode the context requires. In debugging dumps of RTL, `VOIDmode' is expressed by the absence of any mode. `SCmode, DCmode, XCmode, TCmode' These modes stand for a complex number represented as a pair of floating point values. The floating point values are in `SFmode', `DFmode', `XFmode', and `TFmode', respectively. `CQImode, CHImode, CSImode, CDImode, CTImode, COImode' These modes stand for a complex number represented as a pair of integer values. The integer values are in `QImode', `HImode', `SImode', `DImode', `TImode', and `OImode', respectively. The machine description defines `Pmode' as a C macro which expands into the machine mode used for addresses. Normally this is the mode whose size is `BITS_PER_WORD', `SImode' on 32-bit machines. The only modes which a machine description must support are `QImode', and the modes corresponding to `BITS_PER_WORD', `FLOAT_TYPE_SIZE' and `DOUBLE_TYPE_SIZE'. The compiler will attempt to use `DImode' for 8-byte structures and unions, but this can be prevented by overriding the definition of `MAX_FIXED_MODE_SIZE'. Alternatively, you can have the compiler use `TImode' for 16-byte structures and unions. Likewise, you can arrange for the C type `short int' to avoid using `HImode'. Very few explicit references to machine modes remain in the compiler and these few references will soon be removed. Instead, the machine modes are divided into mode classes. These are represented by the enumeration type `enum mode_class' defined in `machmode.h'. The possible mode classes are: `MODE_INT' Integer modes. By default these are `QImode', `HImode', `SImode', `DImode', and `TImode'. `MODE_PARTIAL_INT' The "partial integer" modes, `PSImode' and `PDImode'. `MODE_FLOAT' floating point modes. By default these are `SFmode', `DFmode', `XFmode' and `TFmode'. `MODE_COMPLEX_INT' Complex integer modes. (These are not currently implemented). `MODE_COMPLEX_FLOAT' Complex floating point modes. By default these are `SCmode', `DCmode', `XCmode', and `TCmode'. `MODE_FUNCTION' Algol or Pascal function variables including a static chain. (These are not currently implemented). `MODE_CC' Modes representing condition code values. These are `CCmode' plus any modes listed in the `EXTRA_CC_MODES' macro. *Note Jump Patterns::, also see *Note Condition Code::. `MODE_RANDOM' This is a catchall mode class for modes which don't fit into the above classes. Currently `VOIDmode' and `BLKmode' are in `MODE_RANDOM'. Here are some C macros that relate to machine modes: `GET_MODE (X)' Returns the machine mode of the RTX X. `PUT_MODE (X, NEWMODE)' Alters the machine mode of the RTX X to be NEWMODE. `NUM_MACHINE_MODES' Stands for the number of machine modes available on the target machine. This is one greater than the largest numeric value of any machine mode. `GET_MODE_NAME (M)' Returns the name of mode M as a string. `GET_MODE_CLASS (M)' Returns the mode class of mode M. `GET_MODE_WIDER_MODE (M)' Returns the next wider natural mode. For example, the expression `GET_MODE_WIDER_MODE (QImode)' returns `HImode'. `GET_MODE_SIZE (M)' Returns the size in bytes of a datum of mode M. `GET_MODE_BITSIZE (M)' Returns the size in bits of a datum of mode M. `GET_MODE_MASK (M)' Returns a bitmask containing 1 for all bits in a word that fit within mode M. This macro can only be used for modes whose bitsize is less than or equal to `HOST_BITS_PER_INT'. `GET_MODE_ALIGNMENT (M))' Return the required alignment, in bits, for an object of mode M. `GET_MODE_UNIT_SIZE (M)' Returns the size in bytes of the subunits of a datum of mode M. This is the same as `GET_MODE_SIZE' except in the case of complex modes. For them, the unit size is the size of the real or imaginary part. `GET_MODE_NUNITS (M)' Returns the number of units contained in a mode, i.e., `GET_MODE_SIZE' divided by `GET_MODE_UNIT_SIZE'. `GET_CLASS_NARROWEST_MODE (C)' Returns the narrowest mode in mode class C. The global variables `byte_mode' and `word_mode' contain modes whose classes are `MODE_INT' and whose bitsizes are either `BITS_PER_UNIT' or `BITS_PER_WORD', respectively. On 32-bit machines, these are `QImode' and `SImode', respectively. File: gcc.info, Node: Constants, Next: Regs and Memory, Prev: Machine Modes, Up: RTL Constant Expression Types ========================= The simplest RTL expressions are those that represent constant values. `(const_int I)' This type of expression represents the integer value I. I is customarily accessed with the macro `INTVAL' as in `INTVAL (EXP)', which is equivalent to `XWINT (EXP, 0)'. There is only one expression object for the integer value zero; it is the value of the variable `const0_rtx'. Likewise, the only expression for integer value one is found in `const1_rtx', the only expression for integer value two is found in `const2_rtx', and the only expression for integer value negative one is found in `constm1_rtx'. Any attempt to create an expression of code `const_int' and value zero, one, two or negative one will return `const0_rtx', `const1_rtx', `const2_rtx' or `constm1_rtx' as appropriate. Similarly, there is only one object for the integer whose value is `STORE_FLAG_VALUE'. It is found in `const_true_rtx'. If `STORE_FLAG_VALUE' is one, `const_true_rtx' and `const1_rtx' will point to the same object. If `STORE_FLAG_VALUE' is -1, `const_true_rtx' and `constm1_rtx' will point to the same object. `(const_double:M ADDR I0 I1 ...)' Represents either a floating-point constant of mode M or an integer constant too large to fit into `HOST_BITS_PER_WIDE_INT' bits but small enough to fit within twice that number of bits (GNU CC does not provide a mechanism to represent even larger constants). In the latter case, M will be `VOIDmode'. ADDR is used to contain the `mem' expression that corresponds to the location in memory that at which the constant can be found. If it has not been allocated a memory location, but is on the chain of all `const_double' expressions in this compilation (maintained using an undisplayed field), ADDR contains `const0_rtx'. If it is not on the chain, ADDR contains `cc0_rtx'. ADDR is customarily accessed with the macro `CONST_DOUBLE_MEM' and the chain field via `CONST_DOUBLE_CHAIN'. If M is `VOIDmode', the bits of the value are stored in I0 and I1. I0 is customarily accessed with the macro `CONST_DOUBLE_LOW' and I1 with `CONST_DOUBLE_HIGH'. If the constant is floating point (regardless of its precision), then the number of integers used to store the value depends on the size of `REAL_VALUE_TYPE' (*note Cross-compilation::.). The integers represent a floating point number, but not precisely in the target machine's or host machine's floating point format. To convert them to the precise bit pattern used by the target machine, use the macro `REAL_VALUE_TO_TARGET_DOUBLE' and friends (*note Data Output::.). The macro `CONST0_RTX (MODE)' refers to an expression with value 0 in mode MODE. If mode MODE is of mode class `MODE_INT', it returns `const0_rtx'. Otherwise, it returns a `CONST_DOUBLE' expression in mode MODE. Similarly, the macro `CONST1_RTX (MODE)' refers to an expression with value 1 in mode MODE and similarly for `CONST2_RTX'. `(const_string STR)' Represents a constant string with value STR. Currently this is used only for insn attributes (*note Insn Attributes::.) since constant strings in C are placed in memory. `(symbol_ref:MODE SYMBOL)' Represents the value of an assembler label for data. SYMBOL is a string that describes the name of the assembler label. If it starts with a `*', the label is the rest of SYMBOL not including the `*'. Otherwise, the label is SYMBOL, usually prefixed with `_'. The `symbol_ref' contains a mode, which is usually `Pmode'. Usually that is the only mode for which a symbol is directly valid. `(label_ref LABEL)' Represents the value of an assembler label for code. It contains one operand, an expression, which must be a `code_label' that appears in the instruction sequence to identify the place where the label should go. The reason for using a distinct expression type for code label references is so that jump optimization can distinguish them. `(const:M EXP)' Represents a constant that is the result of an assembly-time arithmetic computation. The operand, EXP, is an expression that contains only constants (`const_int', `symbol_ref' and `label_ref' expressions) combined with `plus' and `minus'. However, not all combinations are valid, since the assembler cannot do arbitrary arithmetic on relocatable symbols. M should be `Pmode'. `(high:M EXP)' Represents the high-order bits of EXP, usually a `symbol_ref'. The number of bits is machine-dependent and is normally the number of bits specified in an instruction that initializes the high order bits of a register. It is used with `lo_sum' to represent the typical two-instruction sequence used in RISC machines to reference a global memory location. M should be `Pmode'. File: gcc.info, Node: Regs and Memory, Next: Arithmetic, Prev: Constants, Up: RTL Registers and Memory ==================== Here are the RTL expression types for describing access to machine registers and to main memory. `(reg:M N)' For small values of the integer N (those that are less than `FIRST_PSEUDO_REGISTER'), this stands for a reference to machine register number N: a "hard register". For larger values of N, it stands for a temporary value or "pseudo register". The compiler's strategy is to generate code assuming an unlimited number of such pseudo registers, and later convert them into hard registers or into memory references. M is the machine mode of the reference. It is necessary because machines can generally refer to each register in more than one mode. For example, a register may contain a full word but there may be instructions to refer to it as a half word or as a single byte, as well as instructions to refer to it as a floating point number of various precisions. Even for a register that the machine can access in only one mode, the mode must always be specified. The symbol `FIRST_PSEUDO_REGISTER' is defined by the machine description, since the number of hard registers on the machine is an invariant characteristic of the machine. Note, however, that not all of the machine registers must be general registers. All the machine registers that can be used for storage of data are given hard register numbers, even those that can be used only in certain instructions or can hold only certain types of data. A hard register may be accessed in various modes throughout one function, but each pseudo register is given a natural mode and is accessed only in that mode. When it is necessary to describe an access to a pseudo register using a nonnatural mode, a `subreg' expression is used. A `reg' expression with a machine mode that specifies more than one word of data may actually stand for several consecutive registers. If in addition the register number specifies a hardware register, then it actually represents several consecutive hardware registers starting with the specified one. Each pseudo register number used in a function's RTL code is represented by a unique `reg' expression. Some pseudo register numbers, those within the range of `FIRST_VIRTUAL_REGISTER' to `LAST_VIRTUAL_REGISTER' only appear during the RTL generation phase and are eliminated before the optimization phases. These represent locations in the stack frame that cannot be determined until RTL generation for the function has been completed. The following virtual register numbers are defined: `VIRTUAL_INCOMING_ARGS_REGNUM' This points to the first word of the incoming arguments passed on the stack. Normally these arguments are placed there by the caller, but the callee may have pushed some arguments that were previously passed in registers. When RTL generation is complete, this virtual register is replaced by the sum of the register given by `ARG_POINTER_REGNUM' and the value of `FIRST_PARM_OFFSET'. `VIRTUAL_STACK_VARS_REGNUM' If `FRAME_GROWS_DOWNWARD' is defined, this points to immediately above the first variable on the stack. Otherwise, it points to the first variable on the stack. `VIRTUAL_STACK_VARS_REGNUM' is replaced with the sum of the register given by `FRAME_POINTER_REGNUM' and the value `STARTING_FRAME_OFFSET'. `VIRTUAL_STACK_DYNAMIC_REGNUM' This points to the location of dynamically allocated memory on the stack immediately after the stack pointer has been adjusted by the amount of memory desired. This virtual register is replaced by the sum of the register given by `STACK_POINTER_REGNUM' and the value `STACK_DYNAMIC_OFFSET'. `VIRTUAL_OUTGOING_ARGS_REGNUM' This points to the location in the stack at which outgoing arguments should be written when the stack is pre-pushed (arguments pushed using push insns should always use `STACK_POINTER_REGNUM'). This virtual register is replaced by the sum of the register given by `STACK_POINTER_REGNUM' and the value `STACK_POINTER_OFFSET'. `(subreg:M REG WORDNUM)' `subreg' expressions are used to refer to a register in a machine mode other than its natural one, or to refer to one register of a multi-word `reg' that actually refers to several registers. Each pseudo-register has a natural mode. If it is necessary to operate on it in a different mode--for example, to perform a fullword move instruction on a pseudo-register that contains a single byte--the pseudo-register must be enclosed in a `subreg'. In such a case, WORDNUM is zero. Usually M is at least as narrow as the mode of REG, in which case it is restricting consideration to only the bits of REG that are in M. Sometimes M is wider than the mode of REG. These `subreg' expressions are often called "paradoxical". They are used in cases where we want to refer to an object in a wider mode but do not care what value the additional bits have. The reload pass ensures that paradoxical references are only made to hard registers. The other use of `subreg' is to extract the individual registers of a multi-register value. Machine modes such as `DImode' and `TImode' can indicate values longer than a word, values which usually require two or more consecutive registers. To access one of the registers, use a `subreg' with mode `SImode' and a WORDNUM that says which register. Storing in a non-paradoxical `subreg' has undefined results for bits belonging to the same word as the `subreg'. This laxity makes it easier to generate efficient code for such instructions. To represent an instruction that preserves all the bits outside of those in the `subreg', use `strict_low_part' around the `subreg'. The compilation parameter `WORDS_BIG_ENDIAN', if set to 1, says that word number zero is the most significant part; otherwise, it is the least significant part. Between the combiner pass and the reload pass, it is possible to have a paradoxical `subreg' which contains a `mem' instead of a `reg' as its first operand. After the reload pass, it is also possible to have a non-paradoxical `subreg' which contains a `mem'; this usually occurs when the `mem' is a stack slot which replaced a pseudo register. Note that it is not valid to access a `DFmode' value in `SFmode' using a `subreg'. On some machines the most significant part of a `DFmode' value does not have the same format as a single-precision floating value. It is also not valid to access a single word of a multi-word value in a hard register when less registers can hold the value than would be expected from its size. For example, some 32-bit machines have floating-point registers that can hold an entire `DFmode' value. If register 10 were such a register `(subreg:SI (reg:DF 10) 1)' would be invalid because there is no way to convert that reference to a single machine register. The reload pass prevents `subreg' expressions such as these from being formed. The first operand of a `subreg' expression is customarily accessed with the `SUBREG_REG' macro and the second operand is customarily accessed with the `SUBREG_WORD' macro. `(scratch:M)' This represents a scratch register that will be required for the execution of a single instruction and not used subsequently. It is converted into a `reg' by either the local register allocator or the reload pass. `scratch' is usually present inside a `clobber' operation (*note Side Effects::.). `(cc0)' This refers to the machine's condition code register. It has no operands and may not have a machine mode. There are two ways to use it: * To stand for a complete set of condition code flags. This is best on most machines, where each comparison sets the entire series of flags. With this technique, `(cc0)' may be validly used in only two contexts: as the destination of an assignment (in test and compare instructions) and in comparison operators comparing against zero (`const_int' with value zero; that is to say, `const0_rtx'). * To stand for a single flag that is the result of a single condition. This is useful on machines that have only a single flag bit, and in which comparison instructions must specify the condition to test. With this technique, `(cc0)' may be validly used in only two contexts: as the destination of an assignment (in test and compare instructions) where the source is a comparison operator, and as the first operand of `if_then_else' (in a conditional branch). There is only one expression object of code `cc0'; it is the value of the variable `cc0_rtx'. Any attempt to create an expression of code `cc0' will return `cc0_rtx'. Instructions can set the condition code implicitly. On many machines, nearly all instructions set the condition code based on the value that they compute or store. It is not necessary to record these actions explicitly in the RTL because the machine description includes a prescription for recognizing the instructions that do so (by means of the macro `NOTICE_UPDATE_CC'). *Note Condition Code::. Only instructions whose sole purpose is to set the condition code, and instructions that use the condition code, need mention `(cc0)'. On some machines, the condition code register is given a register number and a `reg' is used instead of `(cc0)'. This is usually the preferable approach if only a small subset of instructions modify the condition code. Other machines store condition codes in general registers; in such cases a pseudo register should be used. Some machines, such as the Sparc and RS/6000, have two sets of arithmetic instructions, one that sets and one that does not set the condition code. This is best handled by normally generating the instruction that does not set the condition code, and making a pattern that both performs the arithmetic and sets the condition code register (which would not be `(cc0)' in this case). For examples, search for `addcc' and `andcc' in `sparc.md'. `(pc)' This represents the machine's program counter. It has no operands and may not have a machine mode. `(pc)' may be validly used only in certain specific contexts in jump instructions. There is only one expression object of code `pc'; it is the value of the variable `pc_rtx'. Any attempt to create an expression of code `pc' will return `pc_rtx'. All instructions that do not jump alter the program counter implicitly by incrementing it, but there is no need to mention this in the RTL. `(mem:M ADDR)' This RTX represents a reference to main memory at an address represented by the expression ADDR. M specifies how large a unit of memory is accessed. File: gcc.info, Node: Arithmetic, Next: Comparisons, Prev: Regs and Memory, Up: RTL RTL Expressions for Arithmetic ============================== Unless otherwise specified, all the operands of arithmetic expressions must be valid for mode M. An operand is valid for mode M if it has mode M, or if it is a `const_int' or `const_double' and M is a mode of class `MODE_INT'. For commutative binary operations, constants should be placed in the second operand. `(plus:M X Y)' Represents the sum of the values represented by X and Y carried out in machine mode M. `(lo_sum:M X Y)' Like `plus', except that it represents that sum of X and the low-order bits of Y. The number of low order bits is machine-dependent but is normally the number of bits in a `Pmode' item minus the number of bits set by the `high' code (*note Constants::.). M should be `Pmode'. `(minus:M X Y)' Like `plus' but represents subtraction. `(compare:M X Y)' Represents the result of subtracting Y from X for purposes of comparison. The result is computed without overflow, as if with infinite precision. Of course, machines can't really subtract with infinite precision. However, they can pretend to do so when only the sign of the result will be used, which is the case when the result is stored in the condition code. And that is the only way this kind of expression may validly be used: as a value to be stored in the condition codes. The mode M is not related to the modes of X and Y, but instead is the mode of the condition code value. If `(cc0)' is used, it is `VOIDmode'. Otherwise it is some mode in class `MODE_CC', often `CCmode'. *Note Condition Code::. Normally, X and Y must have the same mode. Otherwise, `compare' is valid only if the mode of X is in class `MODE_INT' and Y is a `const_int' or `const_double' with mode `VOIDmode'. The mode of X determines what mode the comparison is to be done in; thus it must not be `VOIDmode'. If one of the operands is a constant, it should be placed in the second operand and the comparison code adjusted as appropriate. A `compare' specifying two `VOIDmode' constants is not valid since there is no way to know in what mode the comparison is to be performed; the comparison must either be folded during the compilation or the first operand must be loaded into a register while its mode is still known. `(neg:M X)' Represents the negation (subtraction from zero) of the value represented by X, carried out in mode M. `(mult:M X Y)' Represents the signed product of the values represented by X and Y carried out in machine mode M. Some machines support a multiplication that generates a product wider than the operands. Write the pattern for this as (mult:M (sign_extend:M X) (sign_extend:M Y)) where M is wider than the modes of X and Y, which need not be the same. Write patterns for unsigned widening multiplication similarly using `zero_extend'. `(div:M X Y)' Represents the quotient in signed division of X by Y, carried out in machine mode M. If M is a floating point mode, it represents the exact quotient; otherwise, the integerized quotient. Some machines have division instructions in which the operands and quotient widths are not all the same; you should represent such instructions using `truncate' and `sign_extend' as in, (truncate:M1 (div:M2 X (sign_extend:M2 Y))) `(udiv:M X Y)' Like `div' but represents unsigned division. `(mod:M X Y)' `(umod:M X Y)' Like `div' and `udiv' but represent the remainder instead of the quotient. `(smin:M X Y)' `(smax:M X Y)' Represents the smaller (for `smin') or larger (for `smax') of X and Y, interpreted as signed integers in mode M. `(umin:M X Y)' `(umax:M X Y)' Like `smin' and `smax', but the values are interpreted as unsigned integers. `(not:M X)' Represents the bitwise complement of the value represented by X, carried out in mode M, which must be a fixed-point machine mode. `(and:M X Y)' Represents the bitwise logical-and of the values represented by X and Y, carried out in machine mode M, which must be a fixed-point machine mode. `(ior:M X Y)' Represents the bitwise inclusive-or of the values represented by X and Y, carried out in machine mode M, which must be a fixed-point mode. `(xor:M X Y)' Represents the bitwise exclusive-or of the values represented by X and Y, carried out in machine mode M, which must be a fixed-point mode. `(ashift:M X C)' Represents the result of arithmetically shifting X left by C places. X have mode M, a fixed-point machine mode. C be a fixed-point mode or be a constant with mode `VOIDmode'; which mode is determined by the mode called for in the machine description entry for the left-shift instruction. For example, on the Vax, the mode of C is `QImode' regardless of M. `(lshiftrt:M X C)' `(ashiftrt:M X C)' Like `ashift' but for right shift. Unlike the case for left shift, these two operations are distinct. `(rotate:M X C)' `(rotatert:M X C)' Similar but represent left and right rotate. If C is a constant, use `rotate'. `(abs:M X)' Represents the absolute value of X, computed in mode M. `(sqrt:M X)' Represents the square root of X, computed in mode M. Most often M will be a floating point mode. `(ffs:M X)' Represents one plus the index of the least significant 1-bit in X, represented as an integer of mode M. (The value is zero if X is zero.) The mode of X need not be M; depending on the target machine, various mode combinations may be valid. File: gcc.info, Node: Comparisons, Next: Bit Fields, Prev: Arithmetic, Up: RTL Comparison Operations ===================== Comparison operators test a relation on two operands and are considered to represent a machine-dependent nonzero value described by, but not necessarily equal to, `STORE_FLAG_VALUE' (*note Misc::.) if the relation holds, or zero if it does not. The mode of the comparison operation is independent of the mode of the data being compared. If the comparison operation is being tested (e.g., the first operand of an `if_then_else'), the mode must be `VOIDmode'. If the comparison operation is producing data to be stored in some variable, the mode must be in class `MODE_INT'. All comparison operations producing data must use the same mode, which is machine-specific. There are two ways that comparison operations may be used. The comparison operators may be used to compare the condition codes `(cc0)' against zero, as in `(eq (cc0) (const_int 0))'. Such a construct actually refers to the result of the preceding instruction in which the condition codes were set. The instructing setting the condition code must be adjacent to the instruction using the condition code; only `note' insns may separate them. Alternatively, a comparison operation may directly compare two data objects. The mode of the comparison is determined by the operands; they must both be valid for a common machine mode. A comparison with both operands constant would be invalid as the machine mode could not be deduced from it, but such a comparison should never exist in RTL due to constant folding. In the example above, if `(cc0)' were last set to `(compare X Y)', the comparison operation is identical to `(eq X Y)'. Usually only one style of comparisons is supported on a particular machine, but the combine pass will try to merge the operations to produce the `eq' shown in case it exists in the context of the particular insn involved. Inequality comparisons come in two flavors, signed and unsigned. Thus, there are distinct expression codes `gt' and `gtu' for signed and unsigned greater-than. These can produce different results for the same pair of integer values: for example, 1 is signed greater-than -1 but not unsigned greater-than, because -1 when regarded as unsigned is actually `0xffffffff' which is greater than 1. The signed comparisons are also used for floating point values. Floating point comparisons are distinguished by the machine modes of the operands. `(eq:M X Y)' 1 if the values represented by X and Y are equal, otherwise 0. `(ne:M X Y)' 1 if the values represented by X and Y are not equal, otherwise 0. `(gt:M X Y)' 1 if the X is greater than Y. If they are fixed-point, the comparison is done in a signed sense. `(gtu:M X Y)' Like `gt' but does unsigned comparison, on fixed-point numbers only. `(lt:M X Y)' `(ltu:M X Y)' Like `gt' and `gtu' but test for "less than". `(ge:M X Y)' `(geu:M X Y)' Like `gt' and `gtu' but test for "greater than or equal". `(le:M X Y)' `(leu:M X Y)' Like `gt' and `gtu' but test for "less than or equal". `(if_then_else COND THEN ELSE)' This is not a comparison operation but is listed here because it is always used in conjunction with a comparison operation. To be precise, COND is a comparison expression. This expression represents a choice, according to COND, between the value represented by THEN and the one represented by ELSE. On most machines, `if_then_else' expressions are valid only to express conditional jumps. `(cond [TEST1 VALUE1 TEST2 VALUE2 ...] DEFAULT)' Similar to `if_then_else', but more general. Each of TEST1, TEST2, ... is performed in turn. The result of this expression is the VALUE corresponding to the first non-zero test, or DEFAULT if none of the tests are non-zero expressions. This is currently not valid for instruction patterns and is supported only for insn attributes. *Note Insn Attributes::. File: gcc.info, Node: Bit Fields, Next: Conversions, Prev: Comparisons, Up: RTL Bit Fields ========== Special expression codes exist to represent bitfield instructions. These types of expressions are lvalues in RTL; they may appear on the left side of an assignment, indicating insertion of a value into the specified bit field. `(sign_extract:M LOC SIZE POS)' This represents a reference to a sign-extended bit field contained or starting in LOC (a memory or register reference). The bit field is SIZE bits wide and starts at bit POS. The compilation option `BITS_BIG_ENDIAN' says which end of the memory unit POS counts from. If LOC is in memory, its mode must be a single-byte integer mode. If LOC is in a register, the mode to use is specified by the operand of the `insv' or `extv' pattern (*note Standard Names::.) and is usually a full-word integer mode. The mode of POS is machine-specific and is also specified in the `insv' or `extv' pattern. The mode M is the same as the mode that would be used for LOC if it were a register. `(zero_extract:M LOC SIZE POS)' Like `sign_extract' but refers to an unsigned or zero-extended bit field. The same sequence of bits are extracted, but they are filled to an entire word with zeros instead of by sign-extension. File: gcc.info, Node: Conversions, Next: RTL Declarations, Prev: Bit Fields, Up: RTL Conversions =========== All conversions between machine modes must be represented by explicit conversion operations. For example, an expression which is the sum of a byte and a full word cannot be written as `(plus:SI (reg:QI 34) (reg:SI 80))' because the `plus' operation requires two operands of the same machine mode. Therefore, the byte-sized operand is enclosed in a conversion operation, as in (plus:SI (sign_extend:SI (reg:QI 34)) (reg:SI 80)) The conversion operation is not a mere placeholder, because there may be more than one way of converting from a given starting mode to the desired final mode. The conversion operation code says how to do it. For all conversion operations, X must not be `VOIDmode' because the mode in which to do the conversion would not be known. The conversion must either be done at compile-time or X must be placed into a register. `(sign_extend:M X)' Represents the result of sign-extending the value X to machine mode M. M must be a fixed-point mode and X a fixed-point value of a mode narrower than M. `(zero_extend:M X)' Represents the result of zero-extending the value X to machine mode M. M must be a fixed-point mode and X a fixed-point value of a mode narrower than M. `(float_extend:M X)' Represents the result of extending the value X to machine mode M. m must be a floating point mode and X a floating point value of a mode narrower than M. `(truncate:M X)' Represents the result of truncating the value X to machine mode M. M must be a fixed-point mode and X a fixed-point value of a mode wider than M. `(float_truncate:M X)' Represents the result of truncating the value X to machine mode M. M must be a floating point mode and X a floating point value of a mode wider than M. `(float:M X)' Represents the result of converting fixed point value X, regarded as signed, to floating point mode M. `(unsigned_float:M X)' Represents the result of converting fixed point value X, regarded as unsigned, to floating point mode M. `(fix:M X)' When M is a fixed point mode, represents the result of converting floating point value X to mode M, regarded as signed. How rounding is done is not specified, so this operation may be used validly in compiling C code only for integer-valued operands. `(unsigned_fix:M X)' Represents the result of converting floating point value X to fixed point mode M, regarded as unsigned. How rounding is done is not specified. `(fix:M X)' When M is a floating point mode, represents the result of converting floating point value X (valid for mode M) to an integer, still represented in floating point mode M, by rounding towards zero. File: gcc.info, Node: RTL Declarations, Next: Side Effects, Prev: Conversions, Up: RTL Declarations ============ Declaration expression codes do not represent arithmetic operations but rather state assertions about their operands. `(strict_low_part (subreg:M (reg:N R) 0))' This expression code is used in only one context: as the destination operand of a `set' expression. In addition, the operand of this expression must be a non-paradoxical `subreg' expression. The presence of `strict_low_part' says that the part of the register which is meaningful in mode N, but is not part of mode M, is not to be altered. Normally, an assignment to such a subreg is allowed to have undefined effects on the rest of the register when M is less than a word.