home *** CD-ROM | disk | FTP | other *** search
-
- XtraDrive and QEMM
-
-
- This QEMM 7 technote is available from the following sources:
-
- Quarterdeck Technical Support BBS: XTRADRV.TEC
- CompuServe: XTRADR.ZIP
- Q/FAX: #199
-
-
- Subject: Frequently asked questions about QEMM and XtraDrive.
-
- XtraDrive is a disk compression program published by Integrated
- Information Technology. While this program is generally
- compatible with QEMM, some issues must be addressed. Below are
- some of the most frequently asked questions about XtraDrive and
- QEMM.
-
-
- STEALTH ROM:
-
- Q: When I try to install XtraDrive on a system that has QEMM and
- Stealth ROM running, I get the following error message:
-
- "Drive 1 is being controlled by a program that appropriates
- INT13. You cannot install XtraDrive on this drive."
-
- What do I have to do to fix this?
-
- A: Remove the Stealth ROM parameter (ST:M or ST:F) from the QEMM
- device line and try to install XtraDrive again. You should only
- need to do this during the installation of XtraDrive. Once
- XtraDrive is installed, you can restore the Stealth ROM
- parameter.
-
- Q: So, I can use XtraDrive with QEMM's Stealth ROM parameter?
-
- A: Under most circumstances, Stealth ROM works fine with
- XtraDrive, but if you are using the XtraDrive EMS cache you
- cannot use either of QEMM's Stealth ROM parameter (ST:M or ST:F.)
- The XtraDrive EMS cache accesses the disk via the page frame and
- this causes a conflict with Stealth ROM. Normally, if a program
- accesses the disk via the page frame, QEMM's DBF=2 parameter will
- fix the problem. This is not possible with XtraDrive. The EMS
- cache will also cause problems with drivers such as EMSNETX.COM
- and Microsoft's MOUSE.COM using EMS.
-
- Q. Are there any other possible conflicts with XtraDrive and
- QEMM's Stealth ROM parameter?
-
- A. Under certain rare circumstances you may need to exclude a 4K
- region in the system ROM BIOS area. If, after installing
- XtraDrive and QEMM with the Stealth ROM parameter, you get an
- Exception 13 or lockup you should refer to Technical Bulletin
- #205, STEALTH.TEC. (This technote is installed in your
- QEMM\TECHNOTE directory when you install QEMM version 7.0) This
- technote will help you determine which area must be excluded.
- Keep in mind, however, that the need to exclude the 4k block of
- High RAM is very rare.
-
-
- EXCLUDES:
-
- Q: When I install QEMM on a system that has XtraDrive currently
- installed, I get a lockup or Exception 13 when I reboot the
- machine, loading QEMM. What do I have to do to allow me to boot
- the system?
-
- A: Simply reboot the machine and when it beeps after checking
- the memory, hold down the ALT key until prompted to press ESC to
- unload QEMM. (If you are using QEMM's DOS-UP, you will first be
- prompted to press ESC to unload DOSDATA.) Once you have unloaded
- DOSDATA and/or QEMM, load your CONFIG.SYS file into a text editor.
- If you have MS-DOS 5 or MS-DOS 6, you may load the DOS Editor, by
- typing EDIT C:\CONFIG.SYS and <ENTER>. At the end of the QEMM
- device line, place the following parameter: X=9000-9FFF.
-
- A sample QEMM device line would then read as follows:
-
- DEVICE=C:\QEMM\QEMM386.SYS RAM ST:M X=9000-9FFF
-
- After adding the parameter, simply save the CONFIG.SYS file and
- reboot your machine.
-
- Q: When I installed XtraDrive after QEMM, XtraDrive placed an
- exclusion from 8000-A000 on the QEMM device line. Do I need this
- exclusion and will it take away any memory from my system?
-
- A: Given the way that XtraDrive is currently designed, an
- exclusion is needed. If you are using DESQview or DESQview/X,
- the exclusion will tell QEMM to not map memory into that area, so
- the amount of memory available to each DESQview window will be
- smaller. There are a couple of things you can do to increase your
- window size if you are using DESQview or DESQview/X:
-
- 1. The default exclude is 8000-A000, a 128K block. Our testing
- has determined that usually an exclusion of 9000-9FFF will be
- sufficient. This will decrease your window size by only 64K. If
- you are using the CONVENTIONAL MEMORY disk cache, and have
- selected more than two 16K blocks of conventional memory, you
- will need to change the exclude back to 8000-9FFF.
-
- OR
-
- 2. Load the XtraDrive driver BEFORE QEMM and take the exclude
- off the QEMM device line. This should decrease your window size
- by only about 46K. Once again, if you are using the CONVENTIONAL
- MEMORY disk cache, your driver size will increase with each 16K
- block you add. The default is one 16K block. If you select two
- blocks, your driver will be 66K. If you select three it will be
- 82K. The maximum, four 16K blocks will result in a 98K driver.
- Your DESQview and DESQview/X window sizes will decrease
- accordingly.
-
-
- BUS-MASTERING:
-
- Q: If I have a SCSI bus-mastering controller, can I load the
- XtraDrive device driver into High Ram?
-
- A: No. Even with double buffering, on a system with a SCSI bus-
- mastering device you will not be able to load XtraDrive into High
- Ram. This is NOT a memory manager issue, but a limitation of
- XtraDrive.
-
- *****************************************************************
- Trademarks are the property of their respective owners.
- This technical note may be copied and distributed freely as long
- as it is distributed in its entirety and it is not distributed
- for profit. Copyright (C) 1993 by Quarterdeck Office Systems
- ****************** E N D O F F I L E *************************