Liren Large Software Subsidy 13/13.iso/p/p034/1.ddi/MESSAGES.LST

File List | 1993-07-25 | 5.6 KB | 115 lines

50) The installation cannot continue due to the following errors:
60) Please, correct the above conditions, then run INSTALL again.
70) The installation program detected the following conditions:
80) Would you like to begin copying files or stop here? (Continue/Stop):
100) ERROR - No math co-processor installed on the system.
101) WARNING - Less than 640K bytes memory in your system. ARC+ can't run.
102) WARNING - No parallel port on your system. ARC+ can't run.
105) ERROR - Less than 250K bytes of free space on c: disk.
107) Destination drive is invalid.
108) Drives a: and b: are invalid as destination drives.
110) ERROR - Less than 7 Meg of free space on destination drive.
111) ERROR - Less than 24 Meg of free space on destination drive.
116) DEBUG - Math processor test failed. Return code
120) ERROR - Unable to open workstation. Check that driver is installed.
121) ERROR - Improper version of graphics driver. Graphics won't work.
122) ERROR - Improper version of graphics driver. No bit map functions.
123) ERROR - Mouse not connected!
124) ERROR - The ANSI.SYS driver is not installed on your system.
125) ERROR - Improper version of graphics driver. No pels functions.
126) ERROR - Must set "files" and "buffers" >= 20 in c:\config.sys.
150) │ ARC+                       INSTALLING ARC+                    Version 6.3 │
151) This program installs ARC+ on disk
155) WARNING - No expanded memory found,this is needed to run the Display List
156) │ ARC+                       INSTALLING ARC+                    Version 6.3 │
157) The program will now copy ARC+ from the system diskettes
158) to Drive
159) The diskette in drive
160) is not System Diskette No.
161) Replace the diskette with the correct one;
162) System Diskette No.
163) Copying and decompressing file:
164) Backing up file:
166) The copy process is now completed.
170) Insert System Diskette No.
171) into drive
172) Backing up user-customized files to directory \ARCA\BAK. Please wait.
173) ERROR - directory doesn't exist:
174) The program will now delete all files in the following directories:
175) Press 'y' to delete and continue, or any other key to stop:
176) Deleting directory:
177) Backup ARCALIB to ARCALIB.BAK ? (y/n)
600) RED LINES
601) GREEN SQUARE
603) Verify screen (ESC-incorrect, Any key-OK)
604) GRAPHICS DISPLAY TEST
700) ERROR - Unable to allocate enough memory to load the parameters file.
701) ERROR - Unable to load the parameters file.
800)  │                           CONFIGURE TABLET MENUS                           │
801) Place the digitizer cursor/stylus on the digitizer
802) and press one of it's buttons.
803) If this message does not disappear, the system did not receive
804) any signal from the digitizer. Please check that it is
805) properly installed and that the switches are set correctly.
806) Press any key on the keyboard to continue.
807) Would you like to try again (y/n)?
808) The digitizer transmits o.k.
809) The system will ask you to indicate points on the tablet menu template.
810)    ││ menu zone                     │           │
811)    ││  │  screen      │             │           │
812)    ││  │  zone        │             │           │
813)    │a ──────────────────────────────┘ digitizer │
814) Now, please indicate point A on the digitizer, and press one of it's buttons.
815) Move the digitizer to point B. Press one of it's keys.
816) Move the digitizer to point C. Press one of it's keys.
817) Move the digitizer to point D. Press one of it's keys.
818) Please enter the dimensions of each rectangle on the template, in millimeters.
819) width =
820) height =
821) Invalid points entered. Please start again. Any key to continue.
900) FAILED TO OPEN WORKSTATION - CARD DRIVER NOT LOADED !!!
901) PKUNZIP - Possible error in file:
902) PKUNZIP - Error in file:
903) PKUNZIP - Insufficient memory, decompression failed for file:
904) PKUNZIP - File not found:
905) PKUNZIP - Bad parameters specified for decompression of file:
906) PKUNZIP - Disk full, could not decompress file:
907) PKUNZIP - Unexpected EOF in file:
908) The UNZIP.BAT program was not found on the destination disk.
909) The installation procedure cannot continue. Please restart the
910) procedure.
911) There is insufficient memory available to run the UNZIP program.
912) The installation procedure cannot continue. Please restart the
913) procedure.
914) Please note the above condition. The installation procedure will
915) continue, however, some files may be missing. Please consult your
916) dealer for more information on this problem.
1000) DIGITIZER DIAGNOSTICS
1001) Current Configuration
1002) Digitizer Type
1003) Driver
1004) Communications Parameters
1005) Point A
1006) Point B
1007) Point C
1008) Point D
1009) Grid Unit Width (mm)
1010) Grid Unit Height (mm)
1011) Current Digitizer Status
1012) Status
1013) Position
1014) Button
1015) <PRESS ESCAPE TO EXIT>
1016) Driver not found.
1017) Driver accessed. Step size =
1018) Press X to change values of A,B,C, and D
1019) Move the digitizer to point A, and press a button
1020) Move the digitizer to point B, and press a button
1021) Move the digitizer to point C, and press a button
1022) Move the digitizer to point D, and press a button
1023) Press any key to continue...
1024) Enter grid unit width in mm, default
1025) Enter grid unit height in mm, default
1026) You are trying to install a regular version of ARC+ on a
1027) Display List version. Continue (y/n) ?