Liren Large Software Subsidy 5

home *** CD-ROM | disk | FTP | other *** search

/ Liren Large Software Subsidy 5 / 05.iso / a / a005 / 1.ddi / 3CSHARE next >

Wrap

Text File | 1992-08-08 | 12.3 KB | 328 lines

INSTALLING PARADOX 4.0 ON A 3COM NETWORK ---------------------------------------- This file contains instructions for installing Paradox on 3Com's 3+ or 3+Share networks. These instructions were verified using 3Com 3PLUS 1.5.1 on an IBM PS/2 Model 60 computer using Compaq-DOS 3.31. TABLE OF CONTENTS ----------------- 1. Assumptions 2. Installation Steps 3. Linking Users and Setting User Paths 1. ASSUMPTIONS -------------- These instructions assume the following about your 3Com installation: - You use 3Com 3+ version 1.1 or higher or 3+Share version 1.0 or higher. - You're familiar with the 3F commands SHARE and LINK NET for 3+ or the command for 3+Share. - The server name is \\SYS. - A directory APPS exists under the root directory. - The sharename APPSADMN has read/write/create rights to the \\SYS\APPS directory, and you're authorized to use this sharename. - The files LOGIN.EXE and 3F.EXE are stored on each workstation's local hard drive and are in each workstation's DOS PATH statement. - You perform all installation and configuration operations from a workstation. 2. INSTALLATION STEPS --------------------- 1) Create a sharename, PDOX40, that gives all users read-only rights to a subdirectory of \\SYS\APPS called PDOX40. The \\SYS\APPS\PDOX40 directory will contain the Paradox system files. By creating the sharename, you automatically create the subdirectory. a. From a workstation with one or more floppy drives, log in as the network server user and link a logical drive, such as F, to the \\SYS\APPS directory. To log in to the network from your local C drive, type LOGIN UserName at the C> system prompt. b. If a password has been assigned to the UserName, type the password when prompted. c. Link a logical drive to the root directory on the server. Type 3F LINK F: d. Display the 3F prompt by typing 3F e. Create the sharename. Display the Share form by typing SHARE ? then fill it in: Sharename? PDOX40 Path? F:\APPS\PDOX40 In this case, F: is a currently mapped logical drive. NOTE: We recommend that you not assign a password to this directory, because users would have to enter the password every time they wanted to use Paradox. Password? (leave blank) Access /R The message \\sys:domainname:orgname\pdox40 shared appears onscreen, where domainname:orgname is the name of your domain and organization. 2) Create a sharename, PDOXADMN, for the PDOX40 system files directory for the network administrator that gives read/write/create rights. Type SHARE ? Specify the following: Sharename? PDOXADMN Path? F:\APPS\PDOX40 NOTE: We recommend that you protect PDOXADMN with a password so unauthorized users can't erase or modify the Paradox system files in the PDOX40 directory. Write down this password and keep it in a safe place for future reference. Password? Password Access /RWC The message \\sys:domainname:orgname\pdoxadmn shared appears onscreen, where domainname:orgname is the name of your domain and organization. 3) Create a sharename that gives all users read/write/create rights to a first-level directory, PDOXDATA. The \\SYS\PDOXDATA directory will contain shared Paradox data files and the network control file PDOXUSRS.NET. By creating the sharename, you automatically create the directory. If you have more than one server, or if your server has more than one hard disk, your choice of which server disk drive to use for the PDOXDATA directory should depend on how heavily Paradox will be used. Take into account the probable growth of your shared data and pick a drive that has enough available storage space. As your network users become familiar with Paradox, they will probably create new Paradox tables and applications. When in doubt, overestimate the amount of space you'll need. NOTE: If your network already has a shared data directory and an associated sharename, you can use them for shared Paradox tables; however, we don't recommend that you do this, because mixing Paradox data with other application data in the same directory makes network housekeeping more difficult. If you do decide to put Paradox data in an existing shared data directory with other applications' shared data, skip this step. To set up the PDOXDATA sharename and directory, type SHARE ? Specify the following: Sharename? PDOXDATA Path? F:\PDOXDATA NOTE: We don't recommend assigning a password to this directory, because users would have to enter the password every time they wanted to access any shared data stored in PDOXDATA. You can password-protect individual tables and applications in this directory; see "Protect" in Chapter 17 of the Paradox "User's Guide." Password? (leave blank) Access /RWC The message \\sys:domainname:orgname\pdoxdata shared appears onscreen, where domainname:orgname is the name of your domain and organization. 4) Link logical drives, such as F and G, to PDOXADMN and PDOXDATA. For example, link your logical drive F to the PDOXDATA directory by typing 3F LINK F: PDOXDATA Link your logical drive G to the PDOX40 directory by typing 3F LINK G: PDOXADMN Because you're using the PDOXADMN sharename, you have read/write/create rights. 5) Exit the 3F utility by pressing [Enter]. 6) Install the Paradox system files and optional software. Follow the instructions in Chapter 2 of the Paradox "Network Installation Guide." The Paradox INSTALL program copies your Paradox system files and optional software from the program disks into the system files directory, PDOX40. 7) Create or modify the CONFIG.SYS file of each workstation to set the number of buffers and files needed by Paradox: FILES=40 BUFFERS=40 A workstation's CONFIG.SYS file must be stored in the root directory of the workstation's hard disk (or on the boot disk if the workstation is started from a floppy disk). See Chapter 2 of the Paradox "Network Installation Guide" for details on CONFIG.SYS. NOTE: After editing the CONFIG.SYS file, you must reboot the workstation before you can run Paradox. To reboot, press [Ctrl][Alt][Del]. 8) Link each user to a private directory. The private directory must be either a network home directory or a private directory on a local hard disk. For information, see "Linking Users and Setting User Paths" later in this file. For information about private directories, see Chapter 1 of the Paradox "Network Installation Guide." 9) Link each user to the Paradox system files directory, PDOX40. For information, see "Linking Users and Setting User Paths" later in this file. 10) Link each user to the directory containing PDOXUSRS.NET, PDOXDATA. For information, see "Linking Users and Setting User Paths" later in this file. 11) Change each Paradox user's path to search for the user's private directory and the Paradox system files directory, IN THAT ORDER. The user's private directory must precede all other Paradox-related directories in the path, since Paradox searches for PARADOX.CFG in the private directory to determine the user's private directory and other default settings. For information, see "Linking Users and Setting User Paths" later in this file. For information about the PARADOX.CFG file, see Chapter 4 of the Paradox Paradox "Network Installation Guide." 12) Create PARADOX.CFG files. See Chapter 4 of the Paradox "Network Installation Guide" for details. 3. LINKING USERS AND SETTING USER PATHS --------------------------------------- You can establish the links and paths for each workstation (steps 8, 9, 10, and 11) in different ways. In theory, network users can enter them manually from their keyboards when they want to use Paradox, but we strongly recommend against this, because a mistake can cause problems for network Paradox users. Instead, we recommend that you automatically create the correct links and path for each user. You can use two methods: - A login batch file that automatically sets up every user to run Paradox when he or she logs in to the network. Use this method for networks where Paradox is used frequently. - A Paradox batch file that sets up the correct links and path when a user starts Paradox. Use this method for networks where Paradox is used infrequently. To use a login batch file ------------------------- On most 3Com networks, each user has an individual batch file (or series of batch files) that logs the user on to the network. The login batch file method uses these batch files to establish the links and paths for Paradox use. The way you structure your login batch commands depends on your particular network. For example, on a network using the three-drive pattern of drive assignments, include the following lines in a login batch file after the line in the batch sequence that logs the user in to 3Com 3+ and prior to any command that loads the 3+ Menus: 3F LINK D: PDOX40 3F LINK F: PDOXDATA PATH = C:\PDOX40; D:\ To use a Paradox batch file --------------------------- Instead of linking to the Paradox directories in a user's login batch file and including the Paradox directories in each user's path, you can create a special Paradox batch file that establishes the links and sets the path each time Paradox is started. Store this batch file in a directory already on everyone's search path, such as the shared applications directory. Since everyone who uses Paradox will run the same Paradox batch file, write the path so that Paradox finds the correct PARADOX.CFG file for each user. The following sample Paradox batch file makes these assumptions: - The network uses the four-drive pattern of drive assignments. - Everyone who uses it is already logged in to the network, and everyone's network home directory is already linked to logical drive E. - All workstations have a local hard disk and a C:\PDOX40 directory to use as a private directory. - The shared applications directory \\SYS\APPS is already linked to each user's logical drive D. Give the batch file an appropriate name, such as PDOX.BAT, and store it in the shared applications directory \\SYS\APPS. Here is the batch file. (If your network doesn't conform to the previous assumptions, you might need to modify it.) PATH>E:\SAVEPATH.BAT 3F LINK F: PDOXDATA 3F LINK G: PDOX40 PATH = C:\PDOX40; G:\; D:\ PARADOX 3F UNLINK F: 3F UNLINK G: COMMAND /C E:\SAVEPATH DEL E:\SAVEPATH.BAT Here are descriptions of the individual lines: - The first line saves the user's current path for later restoration. - The second line links the user's logical drive F to the Paradox shared data directory (containing PDOXUSRS.NET) via the sharename PDOXDATA. What you enter here must match the PDOXUSRS.NET location you entered when you installed Paradox. - The third line links the user's logical drive G to the Paradox system files directory via the sharename PDOX40. - The fourth line sets the correct path so that the private directory on the local hard disk is searched first for the correct PARADOX.CFG file. This example PATH statement includes D:\ so the user has access to the 3Com network software and network batch files. NOTE: If some workstations on the network don't have hard disks, their users must use their network home directory as their private directory (containing a PARADOX.CFG file). In this case, the fourth line would be PATH = E:\; G:\; D:\ With this path, Paradox looks for the PARADOX.CFG file in the user's network home directory, E:. - The fifth line starts Paradox. - The sixth and seventh lines are invoked when the user exits from Paradox; they unlink the PDOXDATA and the PDOX40 directories, respectively. - The eighth line restores the user's original path by running the SAVEPATH.BAT batch file. - The ninth line deletes the SAVEPATH.BAT batch file.