ProfitPress Mega CDROM2 …eeware (MSDOS)(1992)(Eng)/ProfitPress-MegaCDROM2.B6I/MISC/NETWORK/DRIVERS2.ZIP/WD8003E.ASM

Assembly Source File | 1992-01-10 | 16.1 KB | 580 lines

;History:90,1
version    equ    7

    include    defs.asm

;  The following people have contributed to this code: David Horne, Eric
;  Henderson, Bob Clements, and Jan Engvald LDC.

;  Copyright, 1988-1992, Russell Nelson, Crynwr Software

;   This program is free software; you can redistribute it and/or modify
;   it under the terms of the GNU General Public License as published by
;   the Free Software Foundation, version 1.
;
;   This program is distributed in the hope that it will be useful,
;   but WITHOUT ANY WARRANTY; without even the implied warranty of
;   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
;   GNU General Public License for more details.
;
;   You should have received a copy of the GNU General Public License
;   along with this program; if not, write to the Free Software
;   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.

code    segment    byte public
    assume    cs:code, ds:code

; Stuff specific to the Western Digital WD8003E Ethernet controller board
; C version by Bob Clements, K1BC, May 1988 for the KA9Q TCP/IP package

; The EN registers - First, the board registers

EN_CMD        equ    000h    ; Board's command register
EN_REG1        equ    001h    ; 8013 bus size register
EN_REG5        equ    005h    ; New command register (REGISTER 5)
EN_SAPROM    equ    008h    ; Window on station addr prom
EN_REGE        equ    00eh    ; Board Id (code) byte

EN_OFF        equ    10h

ENDCFG_BM8    equ    48h

    include    8390.inc

; Board commands in EN_CMD
EN_RESET    equ    080h    ; Reset the board
EN_MEMEN    equ    040h    ; Enable the shared memory
EN_MEM_MASK    equ    03fh    ; B18-B13 of address of the shared memory

; Bits in REG1
ENR1_BUS16BIT    equ    001h    ; Bus is 16 bits

; Commands for REG5 register
ENR5_MEM16EN    equ    080h    ; Enable 16 bit memory access from bus (8013)
ENR5_LAN16EN    equ    040h    ; Enable 16 bit memory access from chip (8013)
ENR5_MEM_MASK    equ    01fh    ; B23-B19 of address of the memory (8013)
ENR5_LA19    equ    001h    ; B19 of address of the memory (8013)
ENR5_EIL    equ    004h    ; Enable 8390 interrupts to bus (microchannel)

; Bits in the REGE register
ENRE_MICROCHANEL equ    080h    ; Microchannel bus (vs. PC/AT)
ENRE_LARGERAM    equ    040h    ; Large RAM
ENRE_SOFTCONFIG    equ    020h    ; Soft config
ENRE_REVMASK    equ    01eh    ; Revision mask
ENRE_ETHERNET    equ    001h    ; Ethernet (vs. Starlan)

; Shared memory management parameters

SM_TSTART_PG    equ    0    ; First page of TX buffer
SM_RSTART_PG    equ    6    ; Starting page of ring
SM_RSTOP_PG    equ    32    ; Last page +1 of ring

; End of WD8003E parameter definitions

board_features    db    0    ; Board features
BF_MEM16EN    equ    1    ; 16-bit board, enable 16-bit memory
BF_16K        equ    2    ; Board has 16 KB or shared memory

ram_enable    macro
    endm


reset_8390    macro
    loadport        ; First, pulse the board reset
    setport    EN_CMD
    mov    al,EN_RESET        ;Turn on board reset bit
    out    dx,al
    longpause
    xor    al,al            ;Turn off board reset bit
    out    dx,al
    setport    EN_REG5
    mov    al,ENR5_EIL
    test    sys_features,MICROCHANNEL
    jz    reset_no_mc
    out    dx,al            ; enable 8390 interrupts to bus
reset_no_mc:
    endm


terminate_board    macro
    endm

; The following three values may be overridden from the command line.
; If they are omitted from the command line, these defaults are used.

    public    int_no, io_addr, mem_base
int_no        db    3,0,0,0        ; Interrupt level
io_addr        dw    0280h,0        ; I/O address for card (jumpers)
mem_base    dw    0d000h,0    ; Shared memory addr (software)

    public    driver_class, driver_type, driver_name, driver_function, parameter_list
driver_class    db    BLUEBOOK, IEEE8023, 0        ;from the packet spec
driver_type    db    14        ;from the packet spec
driver_name    db    'WD8003E',0    ;name of the driver.
driver_function    db    2
parameter_list    label    byte
    db    1    ;major rev of packet driver
    db    9    ;minor rev of packet driver
    db    14    ;length of parameter list
    db    EADDR_LEN    ;length of MAC-layer address
    dw    GIANT    ;MTU, including MAC headers
    dw    MAX_MULTICAST * EADDR_LEN    ;buffer size of multicast addrs
    dw    0    ;(# of back-to-back MTU rcvs) - 1
    dw    0    ;(# of successive xmits) - 1
int_num    dw    0    ;Interrupt # to hook for post-EOI
            ;processing, 0 == none,

is_186        db    0

    extrn    sys_features: byte

block_output:
;enter with cx = byte count, ds:si = buffer location, ax = buffer address
    assume    ds:nothing
    mov    es,mem_base        ; Set up ES:DI at the shared RAM
    mov    di,ax            ; ..
; Can't use movemem which word aligns to the source, but needs to word
; align to the destination writing to WD8003ET/A. Fortunately works for
; all cards.
    inc    cx        ; if odd bytes round up.
    and    cx,not 1
    call    rcopy_subr

    clc
    ret            ; End of transmit-start routine

block_input:
;enter with cx = byte count, es:di = buffer location, ax = board address.
; Old version checked size, memory space, queue length here. Now done
; in higher level code.
; Set cx to length of this frame.
    assume    ds:nothing,es:nothing
    push    ds
    mov    ds,mem_base        ; ds:si points at first byte to move
    mov    si,ax

    cmp    cx,GIANT
    jbe    rcv_size_ok        ; is the size sane?
    cmp    ch,cl            ; is it starlan bug (dup of low byte)
    jz    rcv_starlan_bug
    mov    cx,1514            ; cap the length
    jmp    rcv_size_ok
rcv_starlan_bug:            ; fix the starlan bug
    mov    ch,ds:[si+EN_RBUF_NXT_PG] ; Page after this frame
    cmp    ch,bl
    ja    rcv_frm_no_wrap
    add    ch,byte ptr cs:sm_rstop_ptr        ; Wrap if needed
    dec    ch
rcv_frm_no_wrap:
    sub    ch,bl
    dec    ch
rcv_size_ok:

    add    ax,cx            ; Find the end of this frame.
    cmp    ah,byte ptr cs:sm_rstop_ptr ; Over the top of the ring?
    jb    rcopy_one_piece        ; Go move it

rcopy_wrap:
; Copy in two pieces due to buffer wraparound.
    mov    ah,byte ptr cs:sm_rstop_ptr ; Compute length of first part
    xor    al,al
    sub    ax,si            ;  as all of the pages up to wrap point
    sub    cx,ax            ; Move the rest in second part
    push    cx            ; Save count of second part
    mov    cx,ax            ; Count for first move
    call    rcopy_subr
    mov    si,SM_RSTART_PG*256    ; Offset to start of first receive page
    pop    cx            ; Bytes left to move
rcopy_one_piece:
    call    rcopy_subr
    pop    ds
    ret


rcopy_subr:
    test    board_features,BF_MEM16EN; Is this a WD8013?
    je    sm_wd8003        ; no, no need to enable 16-bit access.
    loadport            ; Base of device
    setport    EN_REG5            ; Enable 16-bit access
    mov    al,ENR5_MEM16EN+ENR5_LAN16EN+ENR5_LA19
    out    dx,al
    shr    cx,1            ; convert byte count to word count
    rep    movsw            ; Copy packet
    mov    al,ENR5_LAN16EN+ENR5_LA19 ; Disable 16-bit access to WD8013
    out    dx,al
    jmp    short sm_copied
sm_wd8003:
    shr    cx,1            ; convert byte count to word count
    rep    movsw
sm_copied:
    jnc    rcv_wrap_even        ; odd byte left over?
    lodsw                ;   yes, word fetch
    stosb                ;   and byte store
rcv_wrap_even:
    ret


    include    8390.asm

    public    usage_msg
usage_msg    db    "usage: WD8003E [-n] [-d] [-w] <packet_int_no> [-o] <int_level> <io_addr> <mem_base>",CR,LF,'$'

    public    copyright_msg
copyright_msg    db    "Packet driver for Western Digital WD8003 E EBT EB ET/A and E/A, version "
        db    '0'+majver,".",'0'+version,".",'0'+dp8390_version,CR,LF
        db    "Portions Copyright 1988, Robert C. Clements, K1BC",CR,LF,'$'

no_board_msg    label    byte
    db    "WD8003E apparently not present at this memory address.",CR,LF,'$'
bad_cksum_msg    label    byte
    db    "WD8003E not at this I/O address or address PROM bad.",CR,LF,'$'
bad_board_msg    label    byte
    db    "Suggested WD8003E memory address is invalid.",CR,LF,'$'
occupied_msg    label    byte
    db    "Suggested WD8003E memory address already occupied.",CR,LF,'$'
using_16bits    db    "Accessing the board using 16 bits of data.",CR,LF,'$'
int_no_name    db    "Interrupt number ",'$'
io_addr_name    db    "I/O port ",'$'
mem_base_name    db    "Memory address ",'$'

occupied_switch    db    0        ;if zero, don't use occupied test.

    extrn    set_recv_isr: near
    extrn    skip_blanks: near

;enter with si -> argument string, di -> word to store.
;if there is no number, don't change the number.
    extrn    get_number: near

;enter with dx -> name of word, di -> dword to print.
    extrn    print_number: near

    public    parse_args
parse_args:
    call    skip_blanks
    cmp    al,'-'            ;did they specify a switch?
    jne    not_switch
    cmp    byte ptr [si+1],'o'    ;did they specify '-o'?
    je    got_occupied_switch
    stc                ;no, must be an error.
    ret
got_occupied_switch:
    mov    occupied_switch,1
    add    si,2            ;skip past the switch's characters.
    jmp    parse_args        ;go parse more arguments.
not_switch:
; ** start of code added by Reinhard Strebler Universitaet Karlsruhe 1/10/91
    test    sys_features,MICROCHANNEL
    jnz    do_mc_defaults
    jmp    just_parse_args
do_mc_defaults:

; channel selector resides at io 96h
; POS register base is at io 100h
; WD8003E ID is one of 6FC0h, 6FC1h or 6FC2h
; IBM Ethernet Adapter A is EFE5h

; search thro' the slots for a wd8003e card
    mov    cx, 8            ; for all channels(slots)

; channel select value for slots 0,1,2.. is 8,9,A etc
; start with slot 0, and then 7,6,5,4,3,2,1
get_05:
    mov    ax, cx            ; channel number
    or    ax, 08h         ; reg. select value
    mov    dx, 96h         ; channel select register
    out    dx, al            ; select channel

; read adapter id
    mov    dx, 101h
    in    al, dx            ; adapter id - ms byte
    mov    ah, al
    dec    dx
    in    al, dx            ; adapter id - ls byte

; Check if wd8003e
    cmp    ax, 06FC0h
    je    get_10
    cmp    ax, 06FC1h
    je    get_10
    cmp    ax, 06FC2h
    je    get_10
; Check if IBM Ethernet Adapter A
    cmp     ax, 0EFE5h
    je      get_10
    loop    get_05

    mov    dx,offset no_WD8003E_msg
    mov    etopen_diagn,37
    jmp    error_wrt

no_WD8003E_msg:
    db    "WD8003E apparently not found.",CR,LF,'$'

int_xlate db    03,04,10,15

get_10:
; found our Adapter

; Get WD8003E I/O Address ( read POS Register 0 )
    xor    ax,ax
    mov    dx,102h
    in    al,dx
    and    al,0FEh
    mov    cl,4
    shl    ax,cl
    mov    io_addr,ax
; Get WD8003E shared RAM memory address (read POS Register 1 )
    xor    ax,ax
    mov    dx,103h
    in    al,dx
    and    al,0FCh
    xchg    al,ah
    mov    mem_base,ax
; Get WD8003E IRQ (read POS Register 1 )
    xor    ax,ax
    mov    dx,105h
    in    al,dx
    and    al,003h
    mov    bx,offset int_xlate
    xlat    cs:int_xlate
    mov    int_no,al
; ** end of code added by Reinhard Strebler Universitaet Karlsruhe 1/10/91

just_parse_args:
    mov    di,offset int_no
    call    get_number
    mov    di,offset io_addr
    call    get_number
    mov    di,offset mem_base
    call    get_number
    clc
    ret

    extrn    etopen_diagn: byte
addr_not_avail:
    mov    dx,offset occupied_msg
    mov    etopen_diagn,34
bad_cksum:
    mov    dx,offset bad_cksum_msg
    mov    etopen_diagn,37
    jmp    short error_wrt
bad_memory:
    mov    dx,offset bad_board_msg
    mov    etopen_diagn,37
no_memory:
    mov    dx,offset no_board_msg
    mov    etopen_diagn,37
error_wrt:
    mov    ah,9
    int    21h
    stc
    ret


init_card:
; Now get the board's physical address from on-board PROM into card_hw_addr
    assume ds:code

    test    sys_features,MICROCHANNEL
    jz    etopen_no_mc
    or    board_features,BF_16K
    or    endcfg,ENDCFG_WTS
    loadport
    setport    EN_REG5
    mov    al,ENR5_EIL
    out    dx,al        ; enable 8390 interrupts to bus
    jmp    etopen_have_id
etopen_no_mc:            ; Check for WD8013EBT
    loadport        ; WD8013EBT doesn't have register alaasing
    setport    EN_CMD        ; Register 0 may be aliased to Register 8
    mov bx,    dx
    setport    EN_SAPROM
    mov cx,    EN_SAPROM-EN_CMD ; Check 8 bytes
alias_loop:
    in al,    dx        ; Get one register
    mov ah,    al
    xchg bx, dx        ; Switch to other register
    in al,    dx        ; Get other register
    cmp al,    ah        ; Are they the same?
    jne    not_aliased    ; Nope, not aliased
    inc    bx        ; Increment register pair
    inc    dx
    dec    cx        ; Decrement loop counter
    jne    alias_loop    ; Finished?
    jmp    etopen_have_id    ; Aliased; not WD8013EBT
not_aliased:            ; Not aliased; Check for 16-bit board
    loadport
    setport    EN_REG1        ; Bit 0 must be unmodifiable
    in al,    dx        ; Get register 1
    mov bl,    al        ; Store original value
    xor al,    ENR1_BUS16BIT    ; Flip bit 0
    out dx,    al        ; Write it back
    and al,    ENR1_BUS16BIT    ; Throw other bits away
    mov ah,    al        ; Store bit value
    in al,    dx        ; Read register again
    and al,    ENR1_BUS16BIT    ; Throw other bits away
    cmp al,    ah        ; Was it modified?
    jne    board16bit    ; No; board is a WD8013EBT !
    mov al,    bl        ; Get original value
    out dx,    al        ; Write it back
    jmp    etopen_have_id
board16bit:            ; But is it plugged into a 16-bit slot?
    and al,    ENR1_BUS16BIT    ; Throw other bits away
    je    etopen_have_id    ; Nope; silly board installer!
    mov    dx,offset using_16bits
    mov    ah,9
    int    21h
    or    board_features,BF_MEM16EN+BF_16K
    or    endcfg,ENDCFG_WTS
    loadport
    setport    EN_REG5
    mov    al,ENR5_LAN16EN+ENR5_LA19 ; Write LA19 now, but not MEM16EN
    out    dx,al        ; enable 8390 interrupts to bus

etopen_have_id:

    loadport            ; base of device
    setport    EN_SAPROM        ; Where the address prom is
    cld                ; make sure string mode is right
    push    cs            ; Point es:di at local copy space
    pop    es
    mov di,    offset curr_hw_addr
    mov cx,    EADDR_LEN        ; Set count for loop
    xor bx,    bx            ; Clear the addr ROM checksum
ini_addr_loop:
    in    al,dx            ; Get a byte of address
    stosb                ; Feed it to caller
    add    bl,al            ; Compute the checksum
    inc    dx            ; Next byte at next I/O port
    loop    ini_addr_loop        ; Loop over six bytes

    in al,    dx            ; Get seventh byte
    add bl,    al            ; Add it in
    inc    dx            ; Step to eighth byte
    in al,    dx            ; Get last byte
    add bl,    al            ; Final checksum
    cmp bl, 0ffh            ; Correct?
    je    good_cksum
    jmp    bad_cksum        ; No, board is not happy
good_cksum:

; Check if the shared memory address range is available to us
    mov    bx,mem_base
    cmp    occupied_switch,0    ; did they insist?
    jne    no_lim_chk        ; yes, don't check.
    cmp    bh,080h            ; low limit is 8000
    jae    fr_8000
    jmp    bad_memory
fr_8000:
    cmp    bh,0f0h            ; upper limit is F000
    jb    to_f000
    jmp    bad_memory
to_f000:
    test    bx,01ffh        ; must be on a 8 k boundary
    jz    eightk
    jmp    bad_memory
eightk:
no_lim_chk:
    mov    di,8*1024/16        ; 8 kbyte
    mov    sm_rstop_ptr,32
    test    board_features,BF_16K
    jz    just_8k
    mov    cx,16*1024/16        ; 16 kbytes
    mov    sm_rstop_ptr,64
just_8k:
    cmp    occupied_switch,0    ; did they insist?
    jne    is_avail        ; yes, don't check.
    call    occupied_chk        ; check if address range is available
    jnc    is_avail
    jmp    addr_not_avail        ; we HAVE to have at least 8/16 kbyte
is_avail:
    test    board_features,BF_16K
    jnz    not_32k
    mov    di,32*1024/16        ; may be there is space for 32 kbyte
    call    occupied_chk
    jc    not_32k            ; no, then don't try it later either
    and    bh,7
    jnz    not_32k            ; must be on a 32k boundary
    mov    sm_rstop_ptr,128    ; yes, there is space for a WD8003EBT
not_32k:

; Turn on the shared memory block
    loadport
    setport    EN_CMD        ; Point at board command register
    mov ax,    mem_base    ; Find where shared memory will be mapped
    mov al,    ah        ; Shift to right location
    shr al,    1        ;  in the map control word
    and al,    EN_MEM_MASK    ; Just these bits
    or al,    EN_MEMEN    ; Command to turn on map
    test    sys_features,MICROCHANNEL
    jz    AT_card
    mov    al,EN_MEMEN    ; membase handled different for MC card
AT_card:
    out dx,    al        ; Create that memory

; Find how much memory this card has (without destroying other memory)
    mov    si,ax            ; save bord command value
    mov    es,mem_base
    mov    bl,0FFh            ; first try 32 kbyte (WD8003EBT)
    mov    bh,sm_rstop_ptr        ;   or what is available
    dec    bh
memloop:
    dec    bx            ; use even address
    cli                ; disable interrupts
    mov    cx,es:[bx]        ; save old memory contents
    mov    word ptr es:[bx],05A5Ah    ; put testpattern
    loadport
    setport    EN_CCMD            ; drain the board bus for any
    in    al,dx            ;   capacitive memory
    cmp    word ptr es:[bx],05A5Ah    ; any real memory there?
    jne    not_our_mem        ;   no
    setport    EN_CMD            ;   yes
    mov    ax,si
    and    al,0FFh xor EN_MEMEN
    out    dx,al            ; turn off our memory
    jmp    short $+2
    or    al,EN_MEMEN
    cmp    word ptr es:[bx],05A5Ah    ; was it OUR memory?
    out    dx,al            ; turn on our memory.
    jmp    short $+2
    mov    es:[bx],cx        ; restore the original contents.
    sti
    jne    our_mem            ;   yes, it wasn't there any more
not_our_mem:                ;   no, it was still there
    shr    bx,1            ; test if half as much memory
    cmp    bx,1FFFh        ; down to 8 kbyte
    jae    memloop
    jmp    no_memory        ; no memory at address mem_base
our_mem:                ; it IS our memory!
    inc    bh
    mov    sm_rstop_ptr,bh        ; # of 256 byte ring bufs + 1
    mov    ch,bh
    xor    cl,cl
    mov    ax,mem_base
    call    memory_test        ; check all of that memory
    je    mem_ok
    jmp    no_memory
mem_ok:
    ret

    public    print_parameters
print_parameters:
    mov    di,offset int_no
    mov    dx,offset int_no_name
    call    print_number
    mov    di,offset io_addr
    mov    dx,offset io_addr_name
    call    print_number
    mov    di,offset mem_base
    mov    dx,offset mem_base_name
    call    print_number
    ret

    include    memtest.asm
    include    occupied.asm

code    ends

    end