NetNews Usenet Archive 1992 #27/NN_1992_27.iso/spool/sci/electron/19138

Text File | 1992-11-18 | 3.5 KB | 76 lines

Newsgroups: sci.electronics
Path: sparky!uunet!infonode!ingr!b30news!catbyte.b30.ingr.com!medin
From: [e-mail] (Dave Medin)
Subject: Re: How do constant voltage (ferroresonant) transformers work?
Message-ID: <[e-mail]>
Sender: [e-mail] (Usenet Feed)
Reply-To: [e-mail]
Organization: Intergraph Corporation, Huntsville AL
References: <[e-mail]> <[e-mail]>
Date: Wed, 18 Nov 1992 18:58:34 GMT
Lines: 63

In article <[e-mail]>, [e-mail] (John Whitmore) writes:
|> In article <[e-mail]> [e-mail] (Dave Martindale) writes:
|> >I just bought an old Sola CVS-series constant-voltage transformer.
|>
|> >1. How does it WORK?  I can't explain how it does its voltage regulation
|> >   trick with just a transformer and a capacitor.

<Good description on how it works deleted>

|> >2. The label says that the transformer is "harmonic neutralized".  What
|> >   would the output waveform look like without this?
|>
|>     Because saturation is a kind of regulation in itself, it
|> is possible to make a third-harmonic resonant circuit to give
|> roughly square-wave output from a ferroresonant transformer (the
|> design is slightly different from what I described above, I think).

Harmonic neutralization means that the output secondary is resonant,
too (or nearly so), such that distortion products of the regulation
process are removed. Typical THD at full load is about %3 for a
harmonic-neutralized version. This is as clean or cleaner than
your average utility line. The un-neutralized ones have a
very ugly-looking output...

|> >3. What sort of winding temperature would the transformer be designed for?
|> >   I've had it running at a little under 1/2 rated load for a few hours,
|> >   with the input voltage at the lower end of the regulation range,
|> >   and the temperature inside the core is about 70 degrees Celcius.
|> >   This seems a bit high to me for only half load.
|>
|>     Losses in the iron are circa 20% of full rated load, and they
|> DO NOT GO DOWN when the load is lessened.  You are still running
|> a lot of quiescent current in the resonant secondary, after all.
|> Temperature limit on these devices is roughly that of the varnish
|> that insulates the wiring, unless it has soldered connections that
|> would melt first.

The varnish is good for about 120 degrees C, and yes, they run hot
AND hum (magnetostrictive motion in the core).

|>     Reliability is very high.  I have black crinkle-finish
|> CV transformers that work just fine (estimated 40 years old).
|> Also, as surge-protectors go, this kind of device has
|> my vote: it absorbs a surge with a few dozen pounds of steel and
|> copper, not just a wimpy ten-gram MOV.

Yeah, a ferro-resonant transformer is about the best form of
power conditioning you can get. Unfortunately, they're real
expensive unless you can get them surplus. I thought I'd died
and gone to heaven when I got an auction lot of 20 of the 1KW
models. I was vacuumed clean when local HAMs found out about them.

--
--------------------------------------------------------------------
       Dave Medin            Phone:    [phone] (w)
    SSD--Networking                [phone] (h)
    Intergraph Corp.
       M/S GD3004         Internet: [e-mail]
  Huntsville, AL 35894        UUCP:  ...uunet!ingr!b30!catbyte!medin

   ******* Everywhere You Look (at least around my office) *******

 * The opinions expressed here are mine (or those of my machine)