PC World Komputer 1996 February

home *** CD-ROM | disk | FTP | other *** search

/ PC World Komputer 1996 February / PCWK0296.iso / sharewar / dos / program / interupt / interrup.e < prev next >

Wrap

Text File | 1995-08-13 | 349.9 KB | 9,467 lines

Interrupt List, part 5 of 13 This compilation is Copyright (c) 1989,1990,1991,1992,1993,1994,1995 Ralf Brown --------D-214400----------------------------- INT 21 - DOS 2+ - IOCTL - GET DEVICE INFORMATION AX = 4400h BX = handle Return: CF clear if successful DX = device information word (see #0646) AX destroyed CF set on error AX = error code (01h,05h,06h) (see #0885 at AH=59h) Notes: value in DH corresponds to high byte of device driver's attribute word if handle refers to a character device Novell NetWare reportedly does not return a drive number in bits 5-0 for a disk file SeeAlso: AX=4401h,INT 2F/AX=122Bh Bitfields for device information word: Bit(s) Description (Table 0646) character device 14 device driver can process IOCTL requests (see AX=4402h) 13 output until busy supported 11 driver supports OPEN/CLOSE calls 7 set (indicates device) 6 EOF on input 5 raw (binary) mode 4 device is special (uses INT 29) 3 clock device 2 NUL device 1 standard output 0 standard input disk file 15 file is remote (DOS 3.0+) 14 don't set file date/time on closing (DOS 3.0+) 11 media not removable 8 (DOS 4 only) generate INT 24 if no disk space on write or read past end of file 7 clear (indicates file) 6 file has not been written 5-0 drive number (0 = A:) --------D-214401----------------------------- INT 21 - DOS 2+ - IOCTL - SET DEVICE INFORMATION AX = 4401h BX = handle (must refer to character device) DX = device information word (see #0646) (DH must be zero) Return: CF clear if successful CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4400h,INT 2F/AX=122Bh --------D-214402----------------------------- INT 21 - DOS 2+ - IOCTL - READ FROM CHARACTER DEVICE CONTROL CHANNEL AX = 4402h BX = file handle referencing character device CX = number of bytes to read DS:DX -> buffer Return: CF clear if successful AX = number of bytes actually read CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: format of data is driver-specific (see below for some specific cases) SeeAlso: AX=4400h,AX=4403h,AX=4404h,INT 2F/AX=122Bh --------N-214402----------------------------- INT 21 - Network Driver Interface Specification (NDIS) 2.0.1 - PROTOCOL MANAGER AX = 4402h BX = file handle for device "PROTMAN$" CX = 000Eh (size of request block) DS:DX -> request block (see #0647,#0648,#0649,#0650,#0651,#0655,#0656) Return: CF clear if successful AX = number of bytes actually read CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4402h"FTPSOFT" Format of NDIS request block for GetProtocolManagerInfo: Offset Size Description (Table 0647) 00h WORD 01h 02h WORD returned status (see #0657) 04h DWORD returned pointer to structure representing parsed user config 08h DWORD unused 0Ch WORD returned BCD version of NDIS on which Protocol Manager is based SeeAlso: #0648,#0649,#0650,#0651,#0652,#0653,#0654,#0655,#0656 Format of NDIS request block for RegisterModule: Offset Size Description (Table 0648) 00h WORD 02h 02h WORD returned status (see #0657) 04h DWORD pointer to module's common characteristics table (see #0658) 08h DWORD pointer to list of modules to which the module is to be bound 0Ch WORD unused SeeAlso: #0647,#0649,#0650,#0651,#0652,#0653,#0654,#0655,#0656 Format of NDIS request block for BindAndStart: Offset Size Description (Table 0649) 00h WORD 03h 02h WORD returned status (see #0657) 04h DWORD caller's virtual address in FailingModules structure 08h DWORD unused 0Ch WORD unused SeeAlso: #0647,#0648,#0650,#0651,#0652,#0653,#0654,#0655,#0656 Format of NDIS request block for GetProtocolManagerLinkage: Offset Size Description (Table 0650) 00h WORD 04h 02h WORD returned status (see #0657) 04h DWORD returned dispatch point 08h DWORD unused 0Ch WORD returned protocol manager DS Note: the dispatch point may be called as follows instead of using this IOCTL STACK: WORD protocol manager DS DWORD pointer to request block Return: AX = returned status STACK popped SeeAlso: #0647,#0648,#0649,#0651,#0652,#0653,#0654,#0655,#0656 Format of NDIS request block for GetProtocolIniPath: Offset Size Description (Table 0651) 00h WORD 05h 02h WORD returned status (see #0657) 04h DWORD pointer to a buffer for the ASCIZ pathname of PROTOCOL.INI 08h DWORD unused 0Ch WORD buffer length SeeAlso: #0647,#0648,#0649,#0650,#0652,#0653,#0654,#0655,#0656 Format of NDIS request block for RegisterProtocolManagerInfo: Offset Size Description (Table 0652) 00h WORD 06h 02h WORD returned status (see #0657) 04h DWORD pointer to structure containing parsed user config file 08h DWORD unused 0Ch WORD length of structure SeeAlso: #0647,#0648,#0649,#0650,#0651,#0653,#0654,#0655,#0656 Format of NDIS request block for InitAndRegister: Offset Size Description (Table 0653) 00h WORD 07h 02h WORD returned status (see #0657) 04h DWORD unused 08h DWORD poitner to ASCIZ name of the module to be prebind initialized 0Ch WORD unused SeeAlso: #0647,#0648,#0649,#0650,#0651,#0652,#0654,#0655,#0656 Format of NDIS request block for UnbindAndStop: Offset Size Description (Table 0654) 00h WORD 08h 02h WORD returned status (see #0657) 04h DWORD failing modules as for BindAndStart 08h DWORD if not 0000h:0000h, pointer to ASCIZ name of module to unbind if 0000h:0000h, terminate a set of previously dynamically bound protocol modules 0Ch WORD unused SeeAlso: #0647,#0648,#0649,#0650,#0651,#0652,#0653,#0655,#0656 Format of NDIS request block for BindStatus: Offset Size Description (Table 0655) 00h WORD 09h 02h WORD returned status (see #0657) 04h DWORD must be 0000h:0000h on return, points to root tree 08h DWORD 0000h:0000h 0Ch WORD unused under DOS SeeAlso: #0647,#0648,#0649,#0650,#0651,#0652,#0653,#0654,#0656 Format of NDIS request block for RegisterStatus: Offset Size Description (Table 0656) 00h WORD 0Ah 02h WORD returned status (0000h, 0008h, 002Ch) (see #0657) 04h DWORD 0000h:0000h 08h DWORD pointer to 16-byte ASCIZ module name 0Ch WORD 0000h Note: not supported by the 10NET v5.0 PROTMAN$ driver SeeAlso: #0647,#0648,#0649,#0650,#0651,#0652,#0653,#0654,#0655 (Table 0657) Values for NDIS status code: 0000h success 0001h wait for release--protocol has retained control of the data buffer 0002h request queued 0003h frame not recognized 0004h frame rejected 0005h frame should be forwarded 0006h out of resource 0007h invalid parameter 0008h invalid function 0009h not supported 000Ah hardware error 000Bh transmit error 000Ch unrecognized destination 000Dh buffer too small 0020h already started 0021h binding incomplete 0022h driver not initialized 0023h hardware not found 0024h hardware failure 0025h configuration failure 0026h interrupt conflict 0027h MAC incompatible 0028h initialization failed 0029h no binding 002Ah network may be disconnected 002Bh incompatible OS version 002Ch already registered 002Dh path not found 002Eh insufficient memory 002Fh info not found 00FFh general failure F000h-FFFFh reserved for vendor-specific codes, treated as general failure Format of NDIS common characteristics table: Offset Size Description (Table 0658) 00h WORD size of table in bytes 02h BYTE NDIS major version 03h BYTE NDIS minor version 04h WORD reserved 06h BYTE module major version 07h BYTE module minor version 08h DWORD module function flag bits bit 0: binding at upper boundary supported bit 1: binding at lower boundary supported bit 2: dynamically bound bits 3-31 reserved, must be 0 0Ch 16 BYTEs ASCIZ module name 1Ch BYTE upper boundary protocol level (see #0659) 1Dh BYTE upper boundary interface type for MACs: 1 = MAC for data links and transports: to be defined for session: 1 = NCB any level: 0 = private (ISV-defined) 1Eh BYTE lower boundary protocol level (see #0659) 1Fh BYTE lower boundary interface type same as offset 1Dh 20h WORD module ID filled in by protocol manager 22h WORD module DS 24h DWORD system request entry point 28h DWORD pointer to service-specific characteristics (see #0661,#0663) 0000h:0000h if none 2Ch DWORD pointer to service-specific status, or 0000h:0000h if none (see #0664) 30h DWORD pointer to upper dispatch table (see #0660) 0000h:0000h if none 34h DWORD pointer to lower dispatch table (see #0660) 0000h:0000h if none 38h 2 DWORDs reserved, must be 0 Note: for compatibility with NDIS 1.x.x, a major version of 00h is interpreted as 01h (Table 0659) Values for NDIS boundary protocol level: 00h physical 01h Media Access Control 02h Data link 03h network 04h transport 05h session FFh not specified Format of NDIS dispatch table: Offset Size Description (Table 0660) 00h DWORD -> common characteristics table (see #0658) 04h 4 BYTEs ??? 08h DWORD -> ??? function (called with 12 bytes of stack arguments) 0Ch DWORD -> ??? function (called with 10 bytes of stack arguments) 10h DWORD -> ??? function (called with 16 bytes of stack arguments) 14h DWORD -> ??? function (called with 4 bytes of stack arguments) 18h DWORD -> ??? function (called with 18 bytes of stack arguments) 1Ch DWORD -> ??? function (called with 12 bytes of stack arguments) Format of MAC Service-Specific Characteristics Table: Offset Size Description (Table 0661) 00h WORD length of table in bytes 02h 16 BYTEs ASCIZ MAC type name, "802.3", "802.4", "802.5", "802.6", "DIX", "DIX+802.3", "APPLETALK", "ARCNET", "FDDI", "SDLC", "BSC", "HDLC", or "ISDN" 12h WORD length of station addresses in bytes 14h 16 BYTEs permanent station address 24h 16 BYTEs current station address 34h DWORD current functional adapter address (00000000h if none) 38h DWORD pointer to multicast address list 3Ch DWORD link speed in bits/sec 40h DWORD service flags (see #0662) 44h WORD maximum frame size which may be both sent and received 46h DWORD total transmit buffer capacity in bytes 4Ah WORD transmit buffer allocation block size in bytes 4Ch DWORD total receive buffer capacity in bytes 50h WORD receive buffer allocation block size in bytes 52h 3 BYTEs IEEE vendor code 55h BYTE vendor adapter code 56h DWORD pointer to ASCIZ vendor adapter description 5Ah WORD IRQ used by adapter 5Ch WORD transmit queue depth 5Eh WORD maximum supported number of data blocks in buffer descriptors 60h N BYTEs vendor-specific info SeeAlso: #0663 Bitfields for service flags: Bit(s) Description (Table 0662) 0 supports broadcast 1 supports multicast 2 supports functional/group addressing 3 supports promiscuous mode 4 station address software settable 5 statistics always current 6 supports InitiateDiagnostics 7 supports loopback 8 MAC does primarily ReceiveChain indications instead of ReceiveLookahead indications 9 supports IBM source routing 10 supports MAC reset 11 supports Open/Close adapter 12 supports interrupt request 13 supports source routing bridge 14 supports GDT virtual addresses (OS/2 version) 15 multiple TransferDatas allowed durign a single indication 16 MAC normally sets FrameSize = 0 in ReceiveLookahead 17-31 reserved, must be 0 Format of NetBIOS Service-Specific Characteristics Table: Offset Size Description (Table 0663) 00h WORD length of table in bytes 02h 16 BYTEs ASCIZ type name of NetBIOS module 12h WORD NetBIOS module code 14h N BYTEs vendor-specific info SeeAlso: #0661 Format of MAC Service-Specific Status Table: Offset Size Description (Table 0664) 00h WORD length of table in bytes 02h DWORD seconds since 0:00 1/1/70 when diagnostics last run (FFFFFFFFh = never) 06h DWORD MAC status bits (see #0665) 0Ah WORD current packet filter flags (see #0666) 0Ch DWORD pointer to media-specific status table or 0000h:0000h 10h DWORD seconds past 0:00 1/1/70 of last ClearStatistics 14h DWORD total frames received (FFFFFFFFh = not counted) 18h DWORD frames with CRC error (FFFFFFFFh = not counted) 1Ch DWORD total bytes received (FFFFFFFFh = not counted) 20h DWORD frames discarded--no buffer space (FFFFFFFFh = not counted) 24h DWORD multicast frames received (FFFFFFFFh = not counted) 28h DWORD broadcast frames received (FFFFFFFFh = not counted) 2Ch DWORD frames with errors (FFFFFFFFh = not counted) 30h DWORD overly large frames (FFFFFFFFh = not counted) 34h DWORD frames less than minimum size (FFFFFFFFh = not counted) 38h DWORD multicast bytes received (FFFFFFFFh = not counted) 3Ch DWORD broadcast bytes received (FFFFFFFFh = not counted) 40h DWORD frames discarded--hardware error (FFFFFFFFh = not counted) 44h DWORD total frames transmitted (FFFFFFFFh = not counted) 48h DWORD total bytes transmitted (FFFFFFFFh = not counted) 4Ch DWORD multicast frames transmitted (FFFFFFFFh = not counted) 50h DWORD broadcast frames transmitted (FFFFFFFFh = not counted) 54h DWORD broadcast bytes transmitted (FFFFFFFFh = not counted) 58h DWORD multicast bytes transmitted (FFFFFFFFh = not counted) 5Ch DWORD frames not transmitted--timeout (FFFFFFFFh = not counted) 60h DWORD frames not transmitted--hardware error (FFFFFFFFh = not countd) 64h N BYTEs vendor-specific info Bitfields for MAC status bits: Bit(s) Description (Table 0665) 0-2 operational status 000 hardware not installed 001 hardware failed startup diagnostics 010 hardware configuration problem 011 hardware fault 100 operating marginally due to soft faults 101 reserved 110 reserved 111 hardware fully operational 3 MAC bound 4 MAC open 5 diagnostics in progress 6-31 reserved Bitfields for packet filter flags: Bit(s) Description (Table 0666) 0 directed/multicast or group/functional 1 broadcast 2 promiscuous 3 all source routing 4-15 reserved, must be zero --------I-214402----------------------------- INT 21 U - IBM SYSTEM 36/38 WORKSTATION EMULATION - VDI.SYS - GET ??? AX = 4402h BX = handle for character device "GDMS" CX = number of bytes to read (>= 4) DS:DX -> buffer (see #0667) Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful AX = number of bytes read Format of System 36/38 emulator returned data: Offset Size Description (Table 0667) 00h 4 BYTEs ??? 04h DWORD pointer to ??? 08h 4 BYTEs ??? --------m-214402----------------------------- INT 21 U - LASTBYTE.SYS v1.19 - IOCTL - GET ??? TABLE AX = 4402h BX = handle for device "LA$TBYTE" CX = 0004h DS:DX -> DWORD to hold address of 39-byte table of ??? Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful AX = number of bytes read Program: LASTBYTE.SYS is part of the shareware "The Last Byte" memory management package by Key Software Products SeeAlso: AX=4402h"HIGHUMM" --------m-214402----------------------------- INT 21 - HIGHUMM.SYS v1.17+ - IOCTL - GET API ADDRESS AX = 4402h BX = handle for device "KSP$UMM" CX = 0004h DS:DX -> DWORD to hold entry point (see #0668) Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful AX = number of bytes read Program: HIGHUMM.SYS is part of the shareware "The Last Byte" memory management package by Key Software Products SeeAlso: AX=4402h"LASTBYTE" (Table 0668) Call HIGHUMM.SYS entry point with: AH = 00h allocate UMB (same as XMS function 10h) (see INT 2F/AX=4310h) DX = size in paragraphs Return: BX = segment number (if successful) DX = size of requested block/size of largest block AH = 01h deallocate UMB (same as XMS func 11h) (see INT 2F/AX=4310h) DX = segment number of UMB AH = 02h request a bank-switched memory block DX = size in paragraphs Return: BX = segment number (if successful) DX = size of requested block/size of largest block AH = 03h release a bank-switched memory block DX = segment number AH = 04h transfer data to/from high memory DS:SI -> source ES:DI -> destination CX = length in bytes Note: enables bank-switched memory, does the copy, then disables bank-switched memory AH = 05h get a word from bank-switched memory ES:DI -> word to read Return: DX = word AH = 06h put a word to bank-switched memory ES:DI -> word to write DX = word AH = 07h put a byte to bank-switched memory ES:DI -> byte to write DL = byte AH = 08h enable bank-switched memory DS:SI -> 6-byte status save area AH = 09h disable bank-switched memory DS:SI -> 6-byte save area from enable call (AH=08h) AH = 0Ah assign name to UMB or high bank-switched block DX = segment number DS:SI -> 8-byte blank-padded name AH = 0Bh locate UMB block by name DS:SI -> 8-byte blank-padded name Return: BX = segment number (if successful) DX = size of block AH = 0Ch locate bank-switched block by name DS:SI -> 8-byte blank-padded name Return: BX = segment number (if successful) DX = size of block Return: AX = status code 0001h successful 0000h failed BL = error code 80h not implemented B0h insufficient memory, smaller block available B1h insufficient memory, no blocks available B2h invalid segment number Note: only functions 00h and 01h are always available; the remaining functions are only enabled if the proper commandline switch is given --------c-214402----------------------------- INT 21 - SMARTDRV.SYS v3.x only - IOCTL - GET CACHE STATUS AX = 4402h BX = file handle for device "SMARTAAR" CX = number of bytes to read (min 28h) DS:DX -> buffer for status record (see #0669) Return: CF clear if successful AX = number of bytes actually read CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: NCache2 (from the Norton Utilities v8.0) attempts to support this interface, but does not do so correctly, often hanging the system; one should use the SmartDrive v4.x or NCache private interfaces (see INT 2F/AX=4A10h/BX=0000h,INT 2F/AX=FE00h/DI=4E55h) SeeAlso: AX=4403h"SMARTDRV",INT 2F/AX=4A10h/BX=0000h Format of SMARTDRV status record: Offset Size Description (Table 0669) 00h BYTE write-through flag (always 01h) 01h BYTE writes should be buffered (always 00h) 02h BYTE cache enabled if 01h 03h BYTE driver type (01h extended memory, 02h expanded) 04h WORD clock ticks between cache flushes (currently unused) 06h BYTE cache contains locked tracks if nonzero 07h BYTE flush cache on INT 19 reboot if nonzero 08h BYTE cache full track writes if nonzero 09h BYTE double buffering (for VDS) state (00h off, 01h on, 02h dynamic) 0Ah DWORD original INT 13 vector 0Eh BYTE minor version number 0Fh BYTE major version number 10h WORD unused 12h WORD sectors read \ 14h WORD sectors already in cache > may be scaled rather than 16h WORD sectors already in track buffer / absolute counts 18h BYTE cache hit rate in percent 19h BYTE track buffer hit rate in percent 1Ah WORD total tracks in cache 1Ch WORD number of tracks in use 1Eh WORD number of locked tracks 20h WORD number of dirty tracks 22h WORD current cache size in 16K pages 24h WORD original (maximum) cache size in 16K pages 26h WORD minimum cache size in 16K pages 28h DWORD pointer to byte flag to increment for locking cache contents --------d-214402----------------------------- INT 21 - CD-ROM device driver - IOCTL INPUT AX = 4402h BX = file handle referencing character device for CD-ROM driver CX = number of bytes to read DS:DX -> control block (see #0671) Return: CF clear if successful AX = number of bytes actually read CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: the data returned depends on the first byte of the control block; the remainder of the control block is filled by the driver SeeAlso: AX=4403h"CD-ROM",INT 2F/AX=0802h (Table 0670) Values for CD-ROM data being requested: 00h device driver header address 01h drive head location 02h reserved 03h error statistics 04h audio channel info 05h raw drive bytes (uninterpreted and device-specific) 06h device status 07h sector size 08h volume size 09h media change status 0Ah audio disk info 0Bh audio track info 0Ch audio Q-Channel info 0Dh audio sub-channel info 0Eh UPC code 0Fh audio status info Format of CD-ROM control block: Offset Size Description (Table 0671) 00h BYTE data being requested (see #0670) ---function 00h--- 01h DWORD device driver header address (see also AH=52h) ---function 01h--- 01h BYTE addressing mode 00h HSG 01h Red Book 02h DWORD current location of drive's head logical sector number in HSG mode frame/second/minute/unused in Red Book mode (HSG sector = minute * 4500 + second * 75 + frame - 150) ---function 03h--- 01h N BYTEs undefined as of 5 Aug 88 specification ---function 04h--- 01h BYTE input channel (0-3) for output channel 0 02h BYTE volume for output channel 0 03h BYTE input channel (0-3) for output channel 1 04h BYTE volume for output channel 1 05h BYTE input channel (0-3) for output channel 2 06h BYTE volume for output channel 2 07h BYTE input channel (0-3) for output channel 3 08h BYTE volume for output channel 3 Notes: output channels 0 and 1 are left and right, 2 and 3 are left prime and right prime; a volume of 00h is off the default setting is for each input channel to be assigned to the same-numbered output channel at full (FFh) volume ---function 05h--- 01h BYTE number of bytes read 02h 128 BYTEs buffer for drive bytes ---function 06h--- 01h DWORD device parameters (see #0672) ---function 07h--- 01h BYTE read mode 00h cooked 01h raw 02h WORD sector size in bytes ---function 08h--- 01h DWORD volume size in sectors ---function 09h--- 01h BYTE media change status 00h don't know 01h media unchanged FFh media has been changed ---function 0Ah--- 01h BYTE lowest audio track number 02h BYTE highest audio track number 03h DWORD start address of lead-out track (Red Book format) --function 0Bh--- 01h BYTE track number (set by caller) 02h DWORD starting point of track (Red Book format) 06h BYTE track control info bits 15,14,12: track type (notice: bits not contiguous!) 000 two audio channels, no pre-emphasis 001 two audio channels with pre-emphasis 010 data track 100 four audio channels, no pre-emphasis 101 four audio channels with pre-emphasis other reserved bit 13: digital copy permitted ---function 0Ch--- 01h BYTE CONTROL and ADR byte (as received from drive) 02h BYTE track number 03h BYTE point or index 04h BYTE minute \ 05h BYTE second > running time within track 06h BYTE frame / 07h BYTE zero 08h BYTE "AMIN" or "PMIN" \ 09h BYTE "ASEC" or "PSEC" > running time on disk 0Ah BYTE "AFRAME" or "PFRAME" / ---function 0Dh--- 01h DWORD starting frame address (Red Book format) 05h DWORD transfer address 09h DWORD number of sectors to read Note: copies 96 bytes of sub-channel info per sector into buffer ---function 0Eh--- 01h BYTE CONTROL and ADR byte 02h 7 BYTEs UPC/EAN code (13 BCD digits,low-order nybble of last byte is 0) 09h BYTE zero 0Ah BYTE "AFRAME" ---function 0Fh--- ??? documentation not yet available 01h WORD pause status (0000h not paused, 0001h paused) 03h DWORD audio play start address 07h DWORD ??? audio play length or end address Bitfields for CD-ROM device parameters: Bit(s) Description (Table 0672) 0 door open 1 door unlocked 2 supports raw reading in addition to cooked 3 writable 4 can play audio/video tracks 5 supports interleaving 6 reserved 7 supports prefetch requests 8 supports audio channel control 9 supports Red Book addressing in addition to HSG 10 audio is playing 11 no disk in drive 12 supports R-W subchannels --------m-214402----------------------------- INT 21 - Quarterdeck - QEMM-386 v5+ - GET API ENTRY POINT AX = 4402h BX = file handle for device "QEMM386$" CX = 0004h DS:DX -> DWORD buffer for API entry point Return: CF clear if successful buffer filled (see INT 67/AH=3Fh for entry point parameters) CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: Quarterdeck recently (June 1993) documented this function, but the documentation incorrectly states that it is only available for QEMM 6+ SeeAlso: AX=4402h"HOOKROM",INT 2F/AX=D201h/BX=5145h,INT 67/AH=3Fh --------Q-214402----------------------------- INT 21 U - Quarterdeck - HOOKROM.SYS - GET HOOKED VECTOR TABLE AX = 4402h BX = file handle for device "HOOKROM$" CX = 0004h DS:DX -> DWORD buffer for address of hooked vector table (see #0673) Return: CF clear if successful DS:DX buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4402h/SF=01h Format of HOOKROM.SYS hooked vector table entry: Offset Size Description (Table 0673) 00h 5 BYTEs FAR jump to actual interrupt handler (end of table if first byte is not EAh) 05h BYTE interrupt vector number --------d-214402----------------------------- INT 21 - Advanced SCSI Programming Interface (ASPI) - INTERFACE AX = 4402h BX = file handle for device "SCSIMGR$" CX = 0004h or 0005h (see notes) DS:DX -> buffer for result (see #0674), set to zeros before call Return: CF clear if successful AX = 0004h or 0005h (see notes) CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: the variant of the call requesting five bytes is an UNDOCUMENTED extension supported by Adaptec's ASPI2DOS.SYS, ASPI4DOS.SYS, and ASPI7DOS.SYS; if made of a host manager which does not support the variant, only four bytes will be returned. If the variant is supported, Adaptec's WINASPI.DLL assumes that the host manager is an "advanced" one which operates in either real or protected mode (and thus does not require a DPMI INT 31/AX=0301h call to be invoked from protected mode). Support of the five-byte variant also appears to imply that an advanced ASPI host manager uses no temporary storage space except the SRB (see #0676) and the stack, and that it is fully reentrant. if called with a standard request for four bytes, even Adaptec's advanced drivers return only the requested four bytes containing the ASPI entry point address the function address is called with the address of a SCSI Request Block (see #0676) on the stack and the caller must clean up the stack SeeAlso: AX=440Ch"ASPITAPE",INT 11/AH=FFh"WD7000" Format of ASPI IOCTL result: Offset Size Description (Table 0674) 00h DWORD function address 04h BYTE number of SCSI host adapters supported by host manager (Table 0675) Values for ASPI request number: 00h "HA_INQ" host adapter inquiry 01h "GET_TYPE" get device type 02h "EXEC_SIO" execute SCSI I/O 03h "ABORT_SRB" abort SRB 04h "RESET_DEV" reset SCSI device 05h "SET_HAPRMS" set host adapter parameters 06h get disk drive information Format of SCSI Request Block (64 bytes): Offset Size Description (Table 0676) 00h BYTE request number (see #0675) 01h BYTE request status (see #0677) 02h BYTE host adapter ID 03h BYTE request flags (see #0678) 04h DWORD reserved ---request 00h--- 08h BYTE (ret) number of host adapters 09h BYTE (ret) target adapter ID 0Ah 16 BYTEs (ret) SCSI manager ID 1Ah 16 BYTEs (ret) host adapter ID 2Ah 16 BYTEs (ret) host adapter-unique parameters ---request 01h--- 08h BYTE target ID 09h BYTE logical unit number 0Ah BYTE (ret) device type (see #0681) ---request 02h--- 08h BYTE target ID 09h BYTE logical unit number 0Ah DWORD data allocation length 0Eh BYTE sense allocation length 0Fh DWORD data buffer pointer 13h DWORD next request pointer (for linking) 17h BYTE CDB length 18h BYTE (ret) host adapter status (see #0676) 19h BYTE (ret) target status (see #0680) 1Ah DWORD post routine address 1Eh WORD real mode Post DS 20h DWORD SRB pointer 24h WORD reserved 26h DWORD SRB physical address 2Ah 22 BYTEs SCSIMGR$ workspace 40h N BYTEs CCB, including sense data (20-24 bytes) ---request 03h--- 08h DWORD address of SRB to abort ---request 04h--- 08h BYTE target ID 09h BYTE logical unit number 0Ah 14 BYTEs reserved 18h BYTE (ret) host adapter status (see #0679) 19h BYTE (ret) target status (see #0680) 1Ah DWORD post routine address 1Eh 34 BYTEs workspace ---request 05h--- 08h 16 BYTEs host adapter-unique parameters ---request 06h--- 08h BYTE target ID 09h BYTE logical unit number 0Ah BYTE disk drive flags (see #0682) 0Bh BYTE INT 13h drive number 0Ch BYTE preferred head number translation 0Dh BYTE preferred sector size translation 0Eh 10 BYTEs reserved SeeAlso: #0683 (Table 0677) Values for ASPI request status: 00h not done yet 01h completed successfully 02h aborted by host 04h SCSI I/O error 80h invalid 81h no adapter 82h no device attached else status Bitfields for ASPI request flags: Bit(s) Description (Table 0678) 0 posting enabled 1 linking enabled 2 direction 3 transfer from SCSI target to host 4 transfer from host to SCSI target Note: no data is transferred if both bits 3 and 4 are set (Table 0679) Values for host adapter status: 00h no error detected 11h select timeout 12h data overrun 13h bus error 14h bus failure (Table 0680) Values for target status: 00h no status 02h sense data stored in SRB 08h target busy 18h reservation error (Table 0681) Values for device type: 00h disk drive 01h tape drive (streamer) 02h printer 03h processor 04h WORM drive 05h CD-ROM drive 06h scanner 07h optical drive 08h autochanger 09h communications device (Table 0682) Values for disk drive flags: 00h no INT 13 access 01h INT 13 with DOS access 02h INT 13 without DOS access 03h invalid flags Format of CCB: Offset Size Description (Table 0683) 00h BYTE command code (see #0684) 01h BYTE flags bits 4-0: vary by function bits 7-5: logical unit number 02h BYTE "adr_1" 03h BYTE "adr_0" 04h BYTE length 05h BYTE control ... 06h/0Ah 14 BYTEs buffer for sense data (see #0685) SeeAlso: #0676 (Table 0684) Values for CCB command code: 00h test unit ready 01h rewind 03h request sense data 05h get block size limits 08h Group 0 read 0Ah Group 0 write 10h write file marks 11h SCSI Space (set position?) 12h SCSI Inquire 15h set mode information 16h reserve SCSI device 17h release SCSI device 19h erase 1Ah request mode information 1Bh load/unload media 1Dh request target self-check 24h set window parameters 25h get window parameters 28h Group 1 read 2Ah Group 1 write 31h document feeder control 34h get scan data status ---vendor-specific commands--- D3h get document feeder status D4h set document feeder mode Format of sense data: Offset Size Description (Table 0685) 00h BYTE error code (bit 7 set if valid) 01h BYTE segment number 02h BYTE sense key bit 6: EOM bit 5: ILI bits 0-3: sense key (see #0686) 03h 4 BYTEs information bytes 07h BYTE additional sense length (0Ah) 08h 4 BYTEs command-specific information 0Ch BYTE additional sense code 0Dh BYTE additional sense code qualifier 0Eh BYTE field replaceable unit code 0Fh 3 BYTEs sense key specific bytes (Table 0686) Values for sense key: 00h no sense data 02h SCSI unit not ready 03h media error 04h unrecoverable hardware error 05h illegal parameter in CDB 06h target has been reset 0Bh target aborted command --------m-214402----------------------------- INT 21 U - Qualitas 386MAX v6.00+ - IOCTL INPUT - GET STATE AX = 4402h BX = file handle for device "386MAX$$" CX = number of bytes to read DS:DX -> BYTE 03h followed by 386MAX state buffer (see #0687) Return: CF clear if successful buffer at DS:DX+1 filled AX = number of bytes actually copied CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Notes: if the value given in CX is less than the size of the state record (5Ah for v6.01, 66h for v7.00), only a partial state record will be returned the state is 40h bytes for 386MAX (actually ASTEMM) v2.20 ("386MAX$$" did not exist yet, use "QMMXXXX0" and then "EMMXXXX0" instead) and 56h bytes for v5.11. to invoke 386MAX API functions, push DX onto the stack, load DX with the word at offset 25h in the returned state, load all other registers as needed for the desired function, and execute an OUT DX,AL or OUT DX,AX; DX will be set to the pushed value on return if it is not otherwise modified by the API function. For safety, in case a function is not supported or 386MAX is not present, SP should be saved and restored around the API call. Windows 3.1 Standard mode, LAN Manager, and Windows for Workgroups all use the 386MAX API; LAN Manager and Windows for Workgroups reportedly make some calls incorrectly SeeAlso: AX=4403h/SF=03h"386MAX",INT 67/AH=3Fh Format of 386MAX v6.01+ state: Offset Size Description (Table 0687) -1 BYTE (call) 03h 00h 6 BYTEs signature "386MAX" 06h 4 BYTEs version string "N;NN" or "N.NN" (i.e. "6;01" for v6.01) (';' by default; apparently changed to a period when 386MAX has linked high RAM into DOS's memory chain) 0Ah WORD segment of low-memory portion of 386MAX.SYS 0Ch 2 BYTEs ??? 0Eh WORD segment of ??? memory block or 0000h 10h WORD bit flags 1 (see #0688) 12h WORD starting address of video memory in KB 14h 2 BYTEs ??? 16h WORD total high DOS memory in KB 18h 2 BYTEs ??? 1Ah WORD available shared memory in KB 1Ch WORD KBytes extended memory used by 386MAX 1Eh 2 BYTEs ??? 20h WORD total extended memory in KB 22h WORD IO port to write (OUT DX,AL) to invoke 386MAX INT 15 functions 24h WORD IO port to write (OUT DX,AL) to invoke 386MAX API functions (see #0701) 26h WORD ??? (depends on DOS version) 28h WORD size of ??? in paragraphs 2Ah DWORD machine type (see #0696) 2Eh DWORD -> first DOS memory control block 32h WORD system configuration flags (see #0689) 34h WORD debugging flags 1 (see #0690) 36h WORD debugging flags 2 (see #0691) 38h 2 BYTEs ??? 3Ah WORD segment of first MCB in high memory chain 3Ch WORD feature flags 1 (see #0693) 3Eh WORD feature flags 2 (see #0694) 40h WORD feature flags 3 (see #0695) 42h WORD segment of first 386MAX control block??? (see #0697) 44h WORD amount of memory to report available on INT 15/AH=88h 46h 4 BYTEs ??? 4Ah WORD number of K at start of address space swapped with fast extended memory (SWAP= parameter) 4Ch 2 BYTEs ??? 4Eh WORD segment address of ??? 50h WORD debugging flags 3 (see #0692) 52h DWORD old INT 21h 56h DWORD pointer to 386MAX's EMS (INT 67h) handler ---386MAX v7.00--- 5Ah DWORD KB of extended memory managed by 386MAX 5Eh DWORD bytes of extended memory (EXT= parameter) 62h 4 BYTEs ??? Bitfields for 386MAX bit flags 1: Bit(s) Description (Table 0688) 1 ??? 2 allow A20 to be enabled/disabled??? 3 ??? (cleared by calling INT 67 functions or starting MSWindows) 4 high RAM present??? 5 386MAX in AUTO mode 6 386MAX enabled 7 386MAX is providing EMS services 8 ??? (affects API function 08h) 9 A20 gate closed (A20 disabled) (see INT 15/AX=2402h) 10 Weitek support enabled 11 ??? 12 ROMs not shadowed??? 13 QPMS has been used 14 ??? 15 ??? Bitfields for 386MAX system configuration flags: Bit(s) Description (Table 0689) 1 ROM compressed??? 3 ??? 5 386MAX loaded into high memory 6 Microchannel bus 7 Weitek math coprocessor detected 9 ??? (also generates INT 01 on ??? and INT 03 on ???) 11 PC/XT (thus only single 8259 interrupt controller present, DMA only in 1st megabyte, etc) 13 LMLTOP= specified 14 enable A20 control??? 15 ??? Bitfields for 386MAX debugging flags 1: Bit(s) Description (Table 0690) 0 DEBUG=LED 1 DEBUG=X67 2 DEBUG=INV 3 DEBUG=EMSPTED 4 DEBUG=JMP 5 DEBUG=CALL 6 DEBUG=HLT 7 DEBUG=PMR 8 DEBUG=CR3 9 DEBUG=CAPS or DEBUG=INT 10 DEBUG=RC 11 DEBUG=ROM 12 DEBUG=XM 13 DEBUG=SOR 14 DEBUG=XR 15 DEBUG=EMSERR (generate INT 01 on returning error from EMS call) Bitfields for 386MAX debugging flags 2: Bit(s) Description (Table 0691) 0 DEBUG=ROMSWAP 1 DEBUG=UNSHADOWROM 2 DEBUG=COMPROM 3 DEBUG=DPMIPHYS 4 DEBUG=ALLROM 5 DEBUG=VMS 6 DEBUG=XMS (generate INT 01 on XMS calls) 7 DEBUG=I06 8 DEBUG=VCPI 9 DEBUG=XDMA 10 DEBUG=X09 13 DEBUG=I67 (generate INT 01 on every INT 67 call) 14 DEBUG=EVM (generate INT 01 on entering V86 mode) 15 DEBUG=EMSSAVE or DEBUG=VDS Bitfields for 386MAX debugging flags 3: Bit(s) Description (Table 0692) 10 DEBUG=EPM 12 DEBUG=ABIOS 13 DEBUG=XMSPTED 14 DEBUG=TIME 15 DEBUG=SCRUB Bitfields for 386MAX feature flags 1: Bit(s) Description (Table 0693) 1 Weitek present 2 no DPMI services 3 NODMA 4 TERSE 5 NOROM 6 NOPARITY 8 NOFLEX (IGNOREFLEXFRAME) 11 don't create UMBs 12 don't backfill below video memory (NOLOW) 13 FRAME= specified 14 EXT= specified 15 NOEMS, allow prior expanded memory manager to provide EMS Bitfields for 386MAX feature flags 2: Bit(s) Description (Table 0694) 0 UNSHIFT specified (FORCEA20 disabled) 1 NOXRAM 2 NOSCSI specified 3 SCREEN specified 4 enabled EISADMA 5 slow DMA 6 RESETKEYB specified 7 ??? 9 TOP384 10 ??? 11 NOWARMBOOT 12 USE= specified 13 ROM= specified Bitfields for 386MAX feature flags 3: Bit(s) Description (Table 0695) 0 Windows3 support enabled 1 SHADOWROM 2 don't compress ROM (NOCOMPROM) 3 ??? (related to PRGREG=) 4 ??? (related to PRGREG=) 5 SHADOWRAM 6 DOS4 specified 7 NOLOADHIGH 8 NOPULSE 11 FORCEA20 12 DMA buffer enabled 13 NOSCRUB 15 NOFRAME Bitfields for 386MAX machine type: Bit(s) Description (Table 0696) 12 Amstrad 13 Epson 14 Zenith Data Systems 15 "ASEM" 16 NEC 17 "HPRS" model codes 69h and 6Ah 18 Dell 19 "CA" 20 ITT (Xtra Business Systems/Alcatel) 21 Toshiba 5100 22 Olivetti 23 Quadram Quad386 (BIOS model FEh, submodel A6h) 24 Tandy??? 25 AST 386 26 INBOARD, ??? version 27 INBOARD, ??? version 28 INBOARD, ??? version 29 "HPRS" 30 Compaq 386 31 JET386 Format of 386MAX control block: Offset Size Description (Table 0697) 00h WORD segment of next block (FFFFh if last) 02h WORD segment of previous block (FFFFh if first) 04h 12 BYTEs filename 10h WORD resident size in paragraphs 12h WORD environment size??? 14h WORD real prsent environment size + 1 (0000h if ENVSAVE used) 16h 2 BYTEs ??? 18h DWORD initial size or SIZE=n in 386LOAD commandline 1Ch DWORD SIZE=-1 ??? 20h DWORD SIZE= ??? 24h BYTE PRGREG= if specified, else FFh 25h BYTE ENVREG= if specified, else FFh 26h BYTE FlexFrame (00h not present, 01h present) 27h 3 BYTEs ??? 2Ah BYTE GROUP= or 00h if not present 2Bh BYTE ??? 2Ch WORD PSP Format of 386MAX high memory info record: Offset Size Description (Table 0698) 00h WORD segment address of memory region 02h WORD size of memory region in paragraphs 04h BYTE type or flags??? 00h if locked out 02h if EMS page frame 04h if high RAM 42h if ROM 05h BYTE ??? Format of 386MAX ROM shadowing record: Offset Size Description (Table 0699) 00h WORD logical start segment of ROM??? (may be used by BlueMAX when it squeezes together the ROMs to make room) 02h WORD physical start segment of ROM 04h 2 BYTEs ??? 06h WORD size of shadowed ROM in paragraphs 08h 2 BYTEs ??? 0Ah WORD flags bit 15: shadowing enabled for this ROM??? bit 14: ??? bit 13: ??? bit 12: ??? bit 10: ??? (Table 0700) Values for 386MAX memory type: 00h unused by EMS 01h DOS 04h page frame overlapping ROM??? 80h high memory 84h page frame??? 87h video ROM??? Note: the type may be 00h (unused) if the 16K page is split among different uses (such as ROM and high RAM) (Table 0701) Call 386MAX API (via OUT DX,AL) with: STACK: WORD value for DX AH = 00h unused Return: AH = 84h (unsupported function) AH = 01h get high memory information ES:DI -> buffer for array of high memory info records (see #0698) Return: CX = number of records placed in buffer AH = 02h get shadowed ROM info ES:DI -> buffer for array of ROM shadowing records (see #0699) Return: CX = number of records placed in buffer AH = 03h get 386MAX state ES:DI -> 90-byte buffer for state (see #0687) Return: AH = 00h (successful) buffer filled AH = 04h get memory types??? ES:DI -> buffer for memory type info (array of bytes, one per 16K page) (see #0700) Return: CX = number of bytes placed in buffer AH = 05h get page table entries AL = A20 control (00h enable A20 first, 01h leave unchanged) CX = buffer size in bytes (0000h = enough for all memory from given start to end of memory managed by 386MAX) SI = first K to report (rounded down to 4K page) ES:DI -> buffer for returned page table entries Return: CX = number of bytes returned (four per 4K page) ES:DI buffer filled AH = 06h get memory speed info ES:DI -> buffer for memory speed records (see #0702) Return: AH = 00h (successful) CX = number of bytes placed in buffer Note: this function can take over a second to execute AH = 07h map/unmap multiple handle pages DX = EMS handle (on stack) STACK: DWORD -> EMS mapping record Return: AH = status (00h,80h,83h,8Ah,8Bh) Format of EMS mapping record: Offset Size Description 00h WORD function 0000h use physical page numbers 0001h use segment addresses 02h WORD EMS handle 04h WORD number of mapping entries following 06h 2N WORDs logical page number and physical page/segment logical page FFFFh means unmap physical page SeeAlso: INT 67/AH=50h AH = 08h "EMM2_GOREAL" check whether possible to disable 386MAX AL = ??? (00h or nonzero) Return: AH = status (00h OK, A4h not possible at this time) Note: if AL=00h, this function always returns success AH = 09h toggle Bit Flags 1 flags BX = bitmask of bit flags 1's flags to toggle (see #0688) Return: AH = 00h (successful) Note: enables A20 first AH = 0Ah toggle Debugging Flags 1 flags BX = bitmask of Debugging Flags 1's bits to toggle (see #0690) Return: AH = 00h (successful) Notes: enables A20 first does ??? if bit 3 on after specified bits are toggled AH = 0Bh toggle Debugging Flags 2 flags BX = bitmask of Debugging Flags 2's bits to toggle (see #0691) Return: AH = 00h (successful) Note: enables A20 first AH = 0Ch toggle feature flags 3 BX = bitmask of feature flags 3's bits to toggle (see #0695) Return: AH = 00h (successful) Note: enables A20 first AH = 0Dh specify 386MAX high-memory location BX = segment address of high-memory real-mode portion of 386MAX CX = current segment of real-mode stub??? Return: AH = status (00h successful) ??? AH = 0Eh CRT controller register virtualization AL = subfunction 00h allow access to CRTC I/O ports 03B4h/03B5h, 03D4h/03D5h 01h trap accesses to CRTC I/O ports AH = 0Fh reboot system Return: never AH = 10h unused Return: AH = 84h (unsupported function) AH = 11h get high memory information ES:DI -> 96-byte buffer for high memory info Return: AH = 00h (successful) ES:DI buffer filled Notes: each byte in buffer contains bit flags for a 4K page in the A000h-FFFFh region bit 0: page is writeable bit 1: physical address same as linear address bit 2: EMS page frame bit 6: page is part of the QPMS window this function can take over a second to execute, because it does a 128K read for each page in an attempt to flush any RAM cache the system may have AH = 12h shadow RAM mapping AL = subfunction 00h unshadow ROMs (except page FFh if NOWARMBOOT set) 01h map shadow RAM into ROM regions??? Return: AH = 00h (successful) if AL=00h or 01h AH = 8Fh otherwise AH = 13h shadow RAM page protection AL = subfunction 00h set all shadowed ROM 4K pages to read-only 01h set all shadowed ROM 4K pages to read-write Return: AH = 00h (successful) if AL=00h or 01h AH = 8Fh otherwise AH = 14h get Programmable Option Select info??? ES:DI -> 54-byte buffer for POS data??? Return: AH = 00h if successful AH = A4h on error Note: the buffer consists of nine 6-byte fields; the first eight for slots 1-8, the last for the system board AH = 15h ??? ??? Return: ??? AH = 16h get 386MAX memory usage screen ES:DI -> buffer for memory info display CX = size of buffer in bytes Return: ES:DI buffer filled with '$'-terminated string (if large enough to hold entire usage screen) Note: the screen is 0303h bytes in v7.00 AH = 17h Windows 3 startup/termination AL = subfunction 00h Windows3 initializing DX (on stack) = Windows startup flags DI = Windows version number (major in upper byte) ES:BX = 0000h:0000h DS:SI = 0000h:0000h Return: CX = 0000h if OK for Windows to load <> 0 if Windows should not load ES:BX -> startup info structure DS:SI -> Virtual86 mode enable/disable callback 01h Windows3 terminating ES:BX -> ??? DX (on stack) = Windows exit flags Return: ??? AH = 18h QPMS (Qualitas Protected Memory Services) AL = subfunction 00h get QPMS configuration Return: BX = starting segment of QPMS memory window CX = number of 4K pages reserved for QPMS??? DX = number of 4K pages in QPMS window??? 01h map QPMS memory page??? BX = 4K page number within memory reserved for QPMS??? CL = 4K page number within QPMS memory window??? 02h mark all QPMS memory read-only 03h mark all QPMS memory read-write Return: AH = status (00h,8Ah,8Bh,8Fh) AH = 19h get linear address for physical address EDX = physical address (low word on stack) Return: AH = status 00h successful EDX = linear address at which physical address may be accessed 8Bh physical address currently not addressable Note: enables A20 first AH = 1Ah set page table entry EDX = new page table entry (low word on stack) ESI = linear address of page to map (bits 0-11 clear) Return: AH = status (00h,8Bh) Note: enables A20 first AH = 1Bh get ??? Return: AH = status BX = ??? CX = number of ??? EDX = physical address of ??? AH = 1Ch get original interrupt vector AL = interrupt vector (00h-7Fh) Return: AH = 00h (successful) EDX = original vector before 386MAX loaded (segment in high word, offset in low word) Note: no range checking is performed; requests for INTs 80h- FFh will return random values AH = 1Dh display string??? SI = ??? Return: AH = 00h (successful) ??? Note: this function appears to be broken in v7.00 AH = 1Eh get memory info ES:DI -> memory info (see #0703) Return: ??? AH = 1Fh get DPMI host information Return: AX = 0000h if successful BX = DPMI flags (see #1819 at INT 31/AX=0400h) CL = CPU type (02h = 80286, 03h = 80386, etc.) DX = DPMI ver supported (DH=major, DL=2-digit minor) SI = ??? ES???:DI -> ??? Note: NOP if NODPMI switch specified AH = 20h (v7.00) get ??? AL = index of ??? Return: EDX = ??? for specified ??? AH = 21h (v7.00) STACKS support AL = 00h get STACKS parameters Return: BX = ??? (0060h for v7.00) CX = number of stacks for hardware interrupts DX = size of each stack in bytes SI = ??? (low and high bytes are separate values) DI = ??? (low and high bytes are separate values) low byte = logical page number set by subfn 02h ES = ??? AL = 01h set ??? "EMM2_DSTKS" EBX = ??? ECX = ??? AL = 02h set ??? BL = logical page number for ??? (00h-03h) Return: AH = status (00h,8Ah) AH = 22h (v7.00) call ??? for every load module AL = which function to call 00h call ??? else call ???? Return: AH = 00h Note: if AL=00h, calls the protected-mode function pointed at by the DWORD at offset 22h from the start of each module installed by a LOAD= directive; if AL<>00h, it calls the function pointed at by the DWORD at offset 28h of the load module AH = 23h (v7.00) ??? AL = 00h set ??? BL = ??? Return: AH = 00h or unchanged (depending on ???) AL = 01h set ??? BL = ??? BH = ??? CX = ??? DX = ??? (on top of stack) Return: AH = status (00h if successful, 8Fh once table full) Note: this call adds one entry to an internal table on each call, until the table is full AL = 02h get ??? CX = size of buffer ES:DI -> buffer for ??? (60 bytes total data) Return: CX = number of bytes actually returned Note: returns the array storing the values set with AX=2301h Format of one entry in array: Offset Size Description 00h BYTE ??? (BL from subfn 01h) 01h WORD ??? (CX from subfn 01h) 03h BYTE ??? (BH from subfn 01h) 04h WORD ??? (DX from subfn 01h) AL = 03h set ??? name/path ES:DI -> buffer containing ASCIZ ??? AL = 04h get ??? ES:DI -> buffer for ASCIZ ??? Note: the ASCIZ string for subfunctions 03h and 04h does not appear to be used by 386MAX, and may serve merely for communication between two other Qualitas programs AH = 24h (v7.00) high memory control AL = 00h get high memory state Return: BX = current state 00h high memory removed from DOS memory chain 01h high memory included in DOS memory chain AL = 01h set high memory state BX = new state 00h high memory removed from DOS memory chain 01h high memory included in DOS memory chain else Return: ??? (error, but return varies according to ???) AH = 25h (v7.00) remove high RAM from DOS memory chain AH = 26h (v7.00) ??? BX = ??? CX = ??? SI = ??? DI = ??? Return: AH = status BX = ??? CX = ??? AH = 27h (v7.00) ??? AL = 00h get ??? Return: BX = number of paragraphs for ??? AL = 01h ??? BX = ??? ES??? = ??? AL = 02h ??? ??? AL = 03h ??? CX = ??? DX = ??? ES??? = ??? Return: ??? AH = 28h (v7.00) get ??? Return: AH = status (00h,8Fh) (see #2253 at INT 67/AH=40h) if AH=00h, CX = ??? DX = ??? AH = 29h (v7.00) get ??? Return: AX = ??? AH = 40h-5Dh EMS services (see INT 67/AH=40h etc) AH = DEh VCPI services (see INT 67/AX=DE00h etc) Return: AH = status (as for EMS INT 67 calls) 00h successful 80h internal error 81h hardware malfunction 83h invalid handle 84h undefined function 8Ah invalid logical page nuber 8Bh illegal physical page number 8Fh undefined subfunction A4h access denied etc. STACK popped (value placed in DX if no specific return value for DX) Format of 386MAX memory speed record: Offset Size Description (Table 0702) 00h DWORD page table entry for 4K page 04h WORD number of microticks (840ns units) required for REP LODSD of entire 4K page Format of 386MAX memory info [array]: Offset Size Description (Table 0703) 00h DWORD linear start address 04h DWORD size in bytes 08h WORD XMS handle (if next byte = 04h) ??? (if next byte = 05h) ??? (if next byte = 06h) ??? (if next byte = 13h) ??? (if next byte = 14h) ??? (if next byte = 15h) ??? (if next byte = 23h) ??? (if next byte = 24h) ??? (if next byte = 26h) else unused 0Ah BYTE type 00h = ???, 01h = VDISK, 02h = INT 15h extended memory, 03h = ??? extended, 04h = XMS handle's memory, 05h = ???, 06h = ???, 07h = ???, 08h = ???, 09h = ???, 0Ah = ???, 0Bh = ???, 11h = ???, 12h = ???, 14h = ???, 15h = ???, 19h = ???, 1Ah = ???, 1Bh = ???, 1Ch = ???, 1Dh = ???, 1Eh = ???, 1Fh = ???, 20h = ???, 21h = ???, 23h = ???, 24h = ???, 26h = ??? 0Bh BYTE ??? (00h for types 00h-03h, 07h-0Bh, 19h-21h; 80h for types 04h/13h-15h/23h-26h; ??? for type 05h) --------V-214402----------------------------- INT 21 - PGS1600.DEV - IOCTL - GET CONFIGURATION INFO AX = 4402h BX = file handle for device "PGS1600$" CX = 0018h (size of buffer) DS:DX -> configuration buffer (see #0704) Return: CF clear if successful buffer filled AX = number of bytes actually copied CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: PGS1600.DEV is a device driver for the Cornerstone Technology PG1600 display adapter, which provides a 1600x1200 monochrome display as well as one of two emulations, MDA or CGA. SeeAlso: AX=4403h"PGS1600" Format of PGS1600.DEV configuration information: Offset Size Description (Table 0704) 00h WORD version (high byte = major, low byte = minor) 02h WORD board initialisation mode 04h WORD board I/O address 03D0h CGA emulation 03B0h MDA emulation 0390h no emulation 0350h no emulation, alternate 06h WORD emulation buffer segment B800h CGA emulation B000h MDA emulation 0000h no emulation 08h WORD PG1600 graphics buffer segment 0Ah WORD number of bytes between consecutive graphic rows 0Ch WORD horizontal pixel size 0Eh WORD vertical pixel size 10h WORD horizontal dots per inch 12h WORD vertical dots per inch 14h WORD graphics buffer bits per pixel 16h WORD monitor bits per pixel --------N-214402----------------------------- INT 21 - PC/TCP IPCUST.SYS - RESET CONFIGURATION DATA READ POINTER AX = 4402h BX = file handle referencing device "$IPCUST" CX, DS:DX ignored Return: CF clear if successful AX destroyed CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Notes: there are a total of 378h bytes of configuration data for IPCUST.SYS version 2.05. If less than the entire data is read or written, the next read/write continues where the previous one ended; this call and AX=4403h both reset the location at which the next operation starts to zero v2.1+ uses a new configuration method, but allows the installation of IPCUST.SYS for backward compatibility with other software which must read the PC/TCP configuration SeeAlso: AH=3Fh"IPCUST",AH=40h"IPCUST",AX=4403h"IPCUST" --------N-214402----------------------------- INT 21 - WORKGRP.SYS - GET API ENTRY POINT AX = 4402h BX = file handle for device "NET$HLP$" CX = 0008h DS:DX -> buffer for entry point record (see #0705) Return: CF clear if successful AX = number of bytes actually read CF set on error AX = error code Program: WORKGRP.SYS is the portion of Microsoft's Workgroup Connection which permits communication with PCs running Windows for Workgroups or LAN Manager SeeAlso: AH=3Fh"WORKGRP.SYS" Format of WORKGRP.SYS entry point record: Offset Size Description (Table 0705) 00h WORD 3633h \ signature??? 02h WORD EF6Fh / 04h DWORD address of entry point (see #0706) Note: first four bytes of buffer must be 6Fh E9h 33h 36h on entry when using IOCTL rather than READ to get the entry point record (Table 0706) Call WORKGRP entry point with: STACK: WORD function number (0000h-0009h) Return: STACK unchanged SeeAlso: #0707,#0708,#0709,#0710,#0711,#0712,#0713,#0714 (Table 0707) Call WORKGRP function 00h with: STACK: WORD 0000h (function "get ???") Return: DX:AX -> data table (Table 0708) Call WORKGRP function 01h with: STACK: WORD 0001h (function "hook ???") Return: STACK: DWORD pointer to ??? WORD 0001h (function number) (Table 0709) Call WORKGRP function 02h with: STACK: WORD 0002h (function "unhook ???") ??? Return: ??? (Table 0710) Call WORKGRP function 03h with: STACK: WORD 0003h (function "reenable printer port") WORD LPT port number Return: ??? (Table 0711) Call WORKGRP function 04h with: STACK: WORD 0004h (function "disable printer port") WORD LPT port number Return: ??? (Table 0712) Call WORKGRP function 05h with: STACK: WORD 0005h (function "???") ??? Return: ??? (Table 0713) Call WORKGRP function 06h with: STACK: WORD 0006h (function "???") Return: STACK unchanged AX = 0000h DX = 0000h (Table 0714) Call WORKGRP functions 07h-09h with: STACK: WORD 0007h-0009h (NOP functions) Return: STACK unchanged AX = 0001h DX = 0000h --------N-214402----------------------------- INT 21 - 10NET v5.0 - 10BEUI.DOS - API AX = 4402h BX = file handle referencing device "10BEUI$" DS:DX -> parameter record (see #0715) CX ignored Return: CF clear if successful AX destroyed CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4402h"10MEMMGR",INT 6F/AH=00h"10NET" Format of 10NET 10BEUI.DOS parameter record: Offset Size Description (Table 0715) 00h WORD 000Ah (function number???) 02h WORD ??? 04h DWORD pointer to buffer for ??? 08h 4 BYTEs ??? 0Ch WORD transfer size --------N-214402----------------------------- INT 21 - 10NET v5.0 - 10MEMMGR.SYS - API AX = 4402h BX = file handle referencing device "MEMMGR0$" DS:DX -> 6-byte buffer for interface info (see #0716) CX ignored Return: CF clear if successful AX destroyed CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4402h"10BEUI",INT 6F/AH=00h"10NET" Format of 10NET 10MEMMGR.SYS interface info: Offset Size Description (Table 0716) 00h DWORD address of entry point (see #0717) 04h WORD version (0500h for v5.00) (Table 0717) Call 10NET 10MEMMGR.SYS entry point with: AL = 01h ??? BX = ??? Return: CF clear if successful CF set on error AX = error code AL = 02h ??? ??? AL = 03h ??? ??? AL = 04h set/restore memory allocation strategy BX = subfunction 0000h set strategy 0001h restore strategy Return: CF clear if successful CF set on error (if function disabled) various registers destroyed AL = other Return: CF set AX = 0000h BL = 01h --------V-214402----------------------------- INT 21 - Compaq AG1024.SYS - RGDI - GET DRIVER LOCATION AX = 4402h BX = file handle for device "$$$$RGDI" CX = 0006h (size of returned data) DS:DX -> location record (see #0718) Return: CF clear if successful buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: AG1024.SYS is a device driver for the Advanced Graphics 1024 adapter SeeAlso: AX=4403h"RGDI" Format of Compaq AG1024.SYS location record: Offset Size Description (Table 0718) 00h WORD signature 55AAh 02h WORD segment of ??? 04h WORD segment of device driver's code --------N-214402----------------------------- INT 21 - FTPSOFT.DOS v3.1 - GET ??? AX = 4402h BX = file handle for device "FTPSOFT$" CX = size of buffer DS:DX -> buffer for data (see #0719) Return: CF clear if successful buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: FTPSOFT.DOS is a device driver for Protocol Manager support from FTP Software, Inc. SeeAlso: AH=3Fh"PC/TCP",AX=4402h"NDIS" Format of FTPSOFT.DOS data: Offset Size Description (Table 0719) 00h WORD (call) BA98h (if different, no data returned) 02h DWORD -> NDIS common characteristics table (see #0658 at AX=4402h"NDIS") 06h DWORD (call) -> new dispatch table (see #0660 at AX=4402h"NDIS") 0Ah DWORD -> 28-byte buffer for ??? data 0Eh DWORD ??? 12h DWORD -> FAR function to reset dispatch jump table to defaults 16h BYTE ??? Note: the addresses in the new dispatch table are copied into an internal jump table which may be reset by calling the function pointed at by offset 12h --------n-214402----------------------------- INT 21 U - PenDOS PENDEV.SYS - GET ENTRY POINTS AX = 4402h BX = file handle for device "$$PENDOS" or "$$PD_REG" CX = size of buffer (4 for $$PENDOS and a 4,8,12, or 16 for $$PD_REG) DS:DX -> buffer for entry point record (see #0720) Return: CF clear if successful buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: A limited version of PenDOS by Communication Intelligence Corporation, which provides pen capability to keyboard-based programs, is bundled with IBM DOS 6.1 SeeAlso: AX=4403h"PENDEV.SYS" Format of PENDEV.SYS entry point record: Offset Size Description (Table 0720) 00h DWORD -> array of jumps 04h WORD offset of function to retrieve entry point (see #0721) 06h 2 BYTEs signature "Pe" 08h WORD offset of function to set entry point (see #0722) 0Ah 2 BYTEs signature "nD" 0Ch WORD offset of function to clear entry point (see #0723) 0Eh WORD signature "OS" (Table 0721) Call PENDEV.SYS function to retrieve entry point with: AX = index of entry point (0-9) Return: CF clear if successful DX:AX -> desired entry point CF set on error (AX out of range) (Table 0722) Call PENDEV.SYS function to set entry point with: AX = index of entry point (0-9) DX:SI -> new handler Return: CF clear if successful CF set on error (AX out of range) (Table 0723) Call PENDEV.SYS function to clear entry point with: AX = index of entry point (0-9) Return: CF clear if successful CF set on error (AX out of range) Note: resets the jump at the specified entry point to its default target, which simply returns --------N-214402----------------------------- INT 21 U - LAN Manager - TCPDRV.DOS - API AX = 4402h BX = file handle referencing device "TCPDRV$" CX = 0019h DS:DX -> buffer containing request block (see #0724) Return: CF clear if successful buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: TCPDRV.DOS is the low-level device driver supporting LAN Manager's TCP/IP protocol stack Format of TCPDRV.DOS request block: Offset Size Description (Table 0724) 00h BYTE (call) function number 00h initialize ??? 06h get ??? 07h get ??? 01h BYTE (call) 00h (ret) error code if error, unchanged if successful 02h WORD signature 4354h ('CT') ---function 00h--- 04h DWORD (call) pointer to ??? FAR function function is called with ES:BX -> device driver request used to invoke this function 08h 4 BYTEs ??? 0Ch DWORD (call) pointer to ??? record, WORD at offset 22h is read 10h DWORD (ret) -> ??? buffer if 0000h:0000h on call ---function 06h--- 04h 4 BYTEs ??? 08h DWORD (ret) pointer to ??? ---function 07h--- 04h DWORD (ret) pointer to ??? record --------y-214402----------------------------- INT 21 U - PC Tools 9 CPRLOW.EXE - GET CODE AND DATA ADDRESSES AX = 4402h BX = file handle referencing device "RECLOWLD" DS:DX -> buffer for address list (see #0725) CX ignored Return: CF clear if successful buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Format of CPRLOW address list: Offset Size Description (Table 0725) 00h WORD segment of CPRLOW code 02h WORD offset in code segment of ??? entry point (switches into protected mode) 04h WORD offset in code segment of jump array (see #0726) 06h WORD segment of copy of interrupt vector table at CPRLOW load time Note: neither the entry point nor the jump array is valid until after a CPR /LOAD, because CPR.EXE installs the code into CPRLOW at runtime. Format of CPRLOW jump array: Offset Size Description (Table 0726) 00h 3 BYTEs initialize CPRLOW interrupt hooks 03h 3 BYTEs reset timers and enable CPR (hotkey enable) 06h 3 BYTEs disable CPR (hotkey disable) 09h 3 BYTEs clear ??? flag, hotkey disable, and ??? 0Ch 3 BYTEs initialize delay loop counter (destroys AX,BX,CX,DX) 0Fh 3 BYTEs disable CPR completely (commandline /DISABLE) 12h 3 BYTEs enable ??? if CPR enabled by both cmdline and hotkey 15h 3 BYTEs enable CPR (commandline /ENABLE) --------s-214402----------------------------- INT 21 U - Creative Technology CTMMSYS.SYS v1.00.01 - API AX = 4402h BX = file handle for device "CTMMSYS$" CX = 0004h (size of data) DS:DX -> buffer for entry point (see #0727) Return: CF clear if successful buffer updated CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: CTMMSYS.SYS is the Creative DOS Multimedia Architecture Integration driver SeeAlso: AX=4402h"CTSB2",INT 80/BX=0000h"SBFM" Format of CTMMSYS.SYS entry point record: Offset Size Description (Table 0727) 00h DWORD (call) signature 4D6D7443h (ASCII "CtmM") (ret) pointer to CTMMSYS entry point (see #0728) SeeAlso: #0729 (Table 0728) Call CTMMSYS.SYS entry point with: AX = ??? STACK: WORD ??? WORD ??? WORD ??? (0001h,0002h,0005h,0006h) WORD ??? DWORD -> ??? WORD ??? WORD ??? Return: DX:AX = ??? or error code 0000h:000Bh invalid value for ??? 0000h:000Fh API call already in progress SeeAlso: #0727 --------s-214402----------------------------- INT 21 U - Creative Technology CTSB2.SYS v1.01.01 - API AX = 4402h BX = file handle for device "CTSOUND0" CX = 0004h (size of data) DS:DX -> buffer for entry point (see #0729) Return: CF clear if successful buffer updated CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: CTMMSYS.SYS is the Creative DOS Multimedia Architecture Integration driver SeeAlso: AX=4402h"CTMMSYS",INT 80/BX=0000h"SBFM" Format of CTSB2.SYS entry point record: Offset Size Description (Table 0729) 00h DWORD (call) signature 4D6D7443h (ASCII "CtmM") (ret) pointer to CTSB2 entry point (see #0730) SeeAlso: #0727 (Table 0730) Call CTSB2.SYS entry point with: AX = ??? STACK: DWORD -> ??? WORD function number (0100h,0200h,0300h,0400h,0500h,0600h,0701h) DWORD -> ??? WORD ??? WORD ??? Return: DX:AX = ??? or error code 0000h:0004h invalid subfunction??? 0000h:000Bh invalid value for ??? 0000h:000Fh API call already in progress SeeAlso: #0729 --------m-214402----------------------------- INT 21 U - Novell DOS 7 EMM386.EXE - GET STATE RECORD??? AX = 4402h BX = file handle for device "EMMXXXX0" CX = 003Eh (size of state record) DS:DX -> buffer for state record (see #0731) Return: CF clear if successful buffer filled (see #2208 at INT 67/AH=3Fh) CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Format of Novell DOS 7 EMM386.EXE state record: Offset Size Description (Table 0731) 00h WORD signature EDC0h 02h 60 BYTEs ??? --------m-214402SF00------------------------- INT 21 U - Memory Managers - GET API ENTRY POINT AX = 4402h subfn 00h BX = file handle for device "EMMXXXX0" CX = 0006h (size of buffer in bytes) DS:DX -> buffer for API entry point record (see #0732) first byte must be 00h on entry Return: CF clear if successful buffer filled (see #2208 at INT 67/AH=3Fh) CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Notes: this function is supported by Microsoft EMM386.EXE v4.45+ and CEMM v5.10+, and is intended for use by MS Windows as it starts up if no other program has hooked INT 67, an alternate installation check for CEMM is testing for the string "COMPAQ EXPANDED MEMORY MANAGER 386" at offset 14h in the INT 67 handler's segment; if present, the word at offset 12h contains the offset of the API entry point SeeAlso: AX=4402h/SF=01h,AX=4402h/SF=02h,AX=4402h"EMM386",INT 67/AH=3Fh Format of memory manager API entry point record: Offset Size Description (Table 0732) 00h WORD ??? (0022h for CEMM 5.11, 0025h for MS EMM386 v4.45) 02h DWORD manager's private API entry point (see #0733,#2271 at INT 67/AX=FFA5h) (Table 0733) Call CEMM v5.10+ entry point with: AH = 00h get memory manager's state Return: AH = state bit 0: turned OFF bit 1: AUTO mode enabled AH = 01h set memory manager's state AL = new state (00h ON, 01h OFF, 02h AUTO) Return: CF clear if successful CF set on error AH = 02h Weitek coprocessor support AL = subfunction 00h get Weitek support state Return: AL = status bit 0: Weitek coprocessor is present bit 1: Weitek support is enabled 01h turn on Weitek support 02h turn off Weitek support Return: CF clear if successful CF set on error AH = error code (01h invalid subfunc, 02h no Weitek) AH = 05h get statistics ??? AH > 06h Return: CF set AH = 01h (invalid function) Notes: AH=03h,04h,06h are NOPs which return CF clear, presumably for backwards compatibility with earlier versions of CEMM in v5.11, AH=05h merely prints an error message (using INT 21/AH=09h) stating that a different version of CEMM is installed and it is therefore not possible to display the statistics --------m-214402SF01------------------------- INT 21 U - Memory Managers - GET EMM IMPORT STRUCTURE ADDRESS AX = 4402h subfn 01h BX = file handle for device "EMMXXXX0" CX = 0006h (size of buffer in bytes) DS:DX -> buffer for EMM import structure record (see #0734) first byte must be 01h on entry Return: CF clear if successful buffer filled (see also #2208 at INT 67/AH=3Fh) CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Notes: this function is supported by Microsoft EMM386.EXE v4.45+, QEMM-386 v6+, and CEMM v5.10+, and is intended for use by MS Windows as it starts up for QEMM-386, this call always returns an error if Windows3 support has been disabled with the NW3 switch SeeAlso: AX=4402h/SF=00h,AX=4402h"EMM386",INT 2F/AX=D201h/BX=5145h SeeAlso: INT 67/AH=3Fh Format of EMM import structure record: Offset Size Description (Table 0734) 00h DWORD physical address of EMM import structure (see #0735) 04h BYTE EMM import structure major version 05h BYTE EMM import structure minor version Note: version 1.00 contains only EMS information (Windows 3.0+) version 1.10 contains UMB/XMS/HMA/EMS information (Windows 3.1) version 1.11 is version 1.10 plus memory manager maker/product name SeeAlso: #2248 Format of Global EMM Import record: Offset Size Description (Table 0735) 00h BYTE bit flags bit 2: ??? bit 3: free EMM386 virtual HMA only if hma_page_table_paddr!=0 bit 4: no UMB??? 01h BYTE reserved (0) 02h WORD size of structure in bytes 04h WORD structure version 06h DWORD reserved 0Ah 384 BYTEs 64 EMS frame status records (see #0736), one per 16K of real-mode 1M address space 18Ah BYTE ??? (must be at least 3*number_of_EMS_frames+4) 18Bh BYTE number of UMB frame descriptors following 18Ch 4N DWORDs UMB frame descriptors each is 4 DWORDs giving physical page numbers for the four 4K pages of a 16K EMS frame (00000000h if non-UMB page) var BYTE number of EMS handle info records following 16N BYTEs EMS handle info records (see #0738) ---version 1.10+ --- DWORD realmode INT 67 vector (used by Windows to set breakpoints) DWORD physical address of HMA page table values BYTE number of free page entries following 2N DWORDs free page entries each is: DWORD physical page number DWORD number of consecutive physical pages BYTE number of XMS handle info records following 00h if memory manager does not emulate XMS or has real mode XMS code which can execute in the Windows environment 12N BYTEs XMS handle info records (see #0739) BYTE number of free UMB info records following 2N WORDs free UMB info records each is: WORD real mode start segment WORD size in paragraphs ---version 1.11--- 20 BYTEs blank-padded maker name 20 BYTEs blank-padded product name Format of EMS frame status record: Offset Size Description (Table 0736) 00h BYTE frame type (see #0737) 01h BYTE owner handle (00h/FFh = none) from frame including UMB index to UMB frame descriptors 02h WORD logical page for frame, 7FFFh if none, FFFFh if non-EMS frame 04h BYTE EMS physical page number (FFh for non-EMS = don't care???) 05h BYTE flags for non-EMS frames (00h for EMS frame) bits 0,1 for first 4K, bits 2,3 for second 4K, etc: 10: direct mapping (linear address = physical address) 01: UMB mapping Bitfields for EMS frame type: Bit(s) Description (Table 0737) 0 EMS frame 1 (if EMS frame) in standard 64K page frame 2 first 4K of frame is UMB 3 second 4K of frame is UMB 4 third 4K of frame is UMB 5 last 4K of frame is UMB Format of EMS handle info record: Offset Size Description (Table 0738) 00h BYTE handle number (00h = system handle) 01h BYTE flags bit 0: normal handle rather than system handle bit 2: ??? (set by some EMS managers) 02h 8 BYTEs EMS handle's name 0Ah WORD number of 16K pages for handle 0Ch DWORD physical address of page table entries forming page map Note: all values should be zero for the system handle if no large frame support is present Format of XMS handle info record: Offset Size Description (Table 0739) 00h WORD handle 02h WORD flags bit 0: handle usable by Windows (already in use when Windows started if clear) bit 1: reserved (0) 04h DWORD size in KB (may be zero, used only if flags bit 0 set) 08h DWORD physical address (only if flags bit 0 set) --------m-214402SF02------------------------- INT 21 U - Memory Managers - GET MEMORY MANAGER VERSION AX = 4402h subfn 02h BX = file handle for device "EMMXXXX0" CX = 0002h (size of buffer in bytes) DS:DX -> buffer for memory manager version (see #0740) first byte must be 02h on entry Return: CF clear if successful buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: this function is supported by Microsoft EMM386.EXE v4.45+ and CEMM v5.10+, and is intended for use by MS Windows as it starts up SeeAlso: AX=4402h/SF=00h,AX=4402h"EMM386",INT 67/AH=3Fh Format of memory manager version: Offset Size Description (Table 0740) 00h BYTE major version 01h BYTE minor version (binary) --------m-214402----------------------------- INT 21 U - Microsoft EMM386.EXE v4.45 - GET MEMORY MANAGER INFORMATION AX = 4402h BX = file handle for device "EMMXXXX0" CX = size of buffer in bytes (varies, see #0741) DS:DX -> buffer for returned data (see #0741) first byte must be set on entry to indicate desired data Return: CF clear if successful buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Notes: an error is returned if the number of bytes to be read does not match the number of bytes returned for the specified data item this function is part of the interface which allows MS Windows to cooperate with memory managers SeeAlso: AX=4402h/SF=00h,AX=4402h/SF=01h,AX=4402h/SF=02h,INT 67/AX=FFA5h Format of EMM386.EXE data buffer: Offset Size Description (Table 0741) 00h BYTE (call) function 03h get ??? 04h get ??? ---function 03h--- 00h WORD ??? 02h WORD ??? ---function 04h--- 00h WORD segment of UMB containing EMM386 code/data 02h WORD number of paragraphs of EMM386 code/data in UMB 04h WORD ??? ----------214402----------------------------- INT 21 U - IFSHLP.SYS - GET ENTRY POINT AX = 4402h BX = file handle for device "IFS$HLP$" CX = 0008h (size of buffer in bytes) DS:DX -> buffer for entry point record (see #0639 at AH=3Fh"IFSHLP") Return: CF clear if successful buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AH=3Fh"IFSHLP" --------D-214403----------------------------- INT 21 - DOS 2+ - IOCTL - WRITE TO CHARACTER DEVICE CONTROL CHANNEL AX = 4403h BX = file handle referencing character device CX = number of bytes to write DS:DX -> data to write Return: CF clear if successful AX = number of bytes actually written CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Notes: format of data is driver-specific (see below for some specific cases) if the file handle refers to "4DOSSTAK", the 4DOS (v2.x-3.03) KEYSTACK.SYS driver will push the specified characters on the keyboard stack; similarly for "NDOSSTAK", the NDOS KEYSTACK.SYS driver will push the characters onto the keyboard stack SeeAlso: AX=4400h,AX=4402h,AX=4405h,INT 2F/AX=122Bh,INT 2F/AX=D44Dh SeeAlso: INT 2F/AX=D44Fh --------c-214403----------------------------- INT 21 - SMARTDRV.SYS v3.x only - IOCTL - CACHE CONTROL AX = 4403h BX = handle for device "SMARTAAR" CX = number of bytes to write DS:DX -> SMARTDRV control block (see #0743) Return: CF clear if successful AX = number of bytes actually written 0000h if control block too small for given command CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: NCache2 (from the Norton Utilities v8.0) attempts to support this interface, but does not do so correctly, often hanging the system; one should use the SmartDrive v4.x or NCache private interfaces (see INT 2F/AX=4A10h/BX=0000h,INT 2F/AX=FE00h/DI=4E55h) SeeAlso: AX=4402h"SMARTDRV",INT 2F/AX=4A10h/BX=0000h (Table 0742) Values for SMARTDRV function code: 00h flush cache 01h flush and discard cache 02h disable caching (flushes and discards cache first) 03h enable caching 04h control write caching 05h set flushing tick count 06h lock cache contents 07h unlock cache contents 08h set flush-on-reboot flag 09h unused 0Ah control full-track caching 0Bh reduce cache size 0Ch increase cache size 0Dh set INT 13 chain address Format of SMARTDRV control block: Offset Size Description (Table 0743) 00h BYTE function code (see #0742) ---functions 00h-03h,06h,07h--- no additional fields ---function 04h--- 01h BYTE write caching control action 00h turn off write-through 01h turn on write-through 02h turn off write buffering (also flushes cache) 03h turn on write buffering (also flushes cache) ---function 05h--- 01h WORD number of timer ticks between cache flushes ---function 08h--- 01h BYTE new flush-on-reboot flag (00h off, 01h on) ---function 0Ah--- 01h BYTE full-track writes are 00h not cached 01h cached ---functions 0Bh,0Ch--- 01h WORD number of 16K pages by which to increase/reduce cache size ---function 0Dh--- 01h DWORD new address to which to chain on INT 13 Note: the previous address is not preserved --------d-214403----------------------------- INT 21 - CD-ROM device driver - IOCTL OUTPUT AX = 4403h BX = file handle referencing character device for CD-ROM driver CX = number of bytes to write DS:DX -> control block (see #0744) Return: CF clear if successful AX = number of bytes actually written CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4402h"CD-ROM",INT 2F/AX=0802h Format of CR-ROM control block: Offset Size Description (Table 0744) 00h BYTE function code 00h eject disk 01h lock/unlock door 02h reset drive 03h control audio channel 04h write device control string 05h close tray ---functions 00h,02h,05h--- no further fields ---function 01h--- 01h BYTE lock function 00h unlock door 01h lock door ---function 03h--- 01h BYTE input channel (0-3) for output channel 0 02h BYTE volume for output channel 0 03h BYTE input channel (0-3) for output channel 1 04h BYTE volume for output channel 1 05h BYTE input channel (0-3) for output channel 2 06h BYTE volume for output channel 2 07h BYTE input channel (0-3) for output channel 3 08h BYTE volume for output channel 3 Note: output channels 0 and 1 are left and right, 2 and 3 are left prime and right prime; a volume of 00h is off ---function 04h--- 01h N BYTEs bytes to send directly to the CD-ROM drive without interpretation --------d-214403----------------------------- INT 21 - Brian Antoine Seagate ST-01 SCSI.SYS - IOCTL - EXECUTE COMMANDS AX = 4403h BX = handle for device "SCSITAPE" CX = number of bytes to write DS:DX -> SCSITAPE control block (see #0745) Return: CF clear if successful AX = number of bytes actually written CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4405h"ST-01",INT 78/AH=10h Format of SCSITAPE control block: Offset Size Description (Table 0745) 00h WORD command type 'F' Format (argument 1 = interleave, argument 2 = format type) 'E' Erase 'R' Rewind 'L' Load 'N' No Load 'S' Space (argument 1 = count, argument 2 = type) 'M' File Mark (argument 1 = count) 'A' Reassign 02h WORD argument 1 04h WORD argument 2 06h WORD segment of command buffer 08h WORD offset of command buffer 0Ah WORD length of command buffer --------E-214403----------------------------- INT 21 U - AI Architects - OS/x86??? - API AX = 4403h BX = handle for device "AIA_OS" CX = number of bytes to write (ignored) DS:DX -> 12-byte buffer (see #0746), first byte is command: 81h installation check 82h get API entry point 84h uninstall Return: CF clear if successful AX = number of bytes actually written DS:DX buffer filled CF set on error AX = error code (01h,05h,06h,0Ch,0Dh) (see #0885 at AH=59h) Notes: these functions are only available if the DOS extender was loaded as a device driver in CONFIG.SYS called by TKERNEL (a licensed version of AI Architects/Ergo OS/x86) SeeAlso: INT 2F/AX=FBA1h/BX=0081h,INT 2F/AX=FBA1h/BX=0082h Index: installation check;OS/x86|entry point;OS/x86|uninstall;OS/x86 Format of buffer on return: Offset Size Description (Table 0746) 00h 4 BYTEs signature "IABH" ---if function 81h--- (no additional fields) ---if function 82h--- 04h DWORD pointer to API entry point (see INT 2F/AX=FBA1h/BX=0082h) ---if function 84h--- 04h WORD success indicator 06h WORD segment of ??? 08h WORD segment of ??? memory block to free if nonzero 0Ah WORD segment of ??? memory block to free if nonzero --------V-214403----------------------------- INT 21 - PGS1600.DEV - IOCTL - SET CONFIGURATION??? AX = 4403h BX = file handle for device "PGS1600$" CX = 0018h (size of buffer) DS:DX -> configuration buffer (see #0704 at AX=4402h"PGS1600") Return: CF clear if successful AX = number of bytes actually written CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: PGS1600.DEV is a device driver for the Cornerstone Technology PG1600 display adapter, which provides a 1600x1200 monochrome display as well as one of two emulations, MDA or CGA. SeeAlso: AX=4402h"PGS1600" --------N-214403----------------------------- INT 21 - PC/TCP IPCUST.SYS - RESET CONFIGURATION DATA READ POINTER AX = 4403h BX = file handle referencing device "$IPCUST" CX, DS:DX ignored Return: CF clear if successful AX destroyed CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Notes: there are a total of 378h bytes of configuration data for IPCUST.SYS version 2.05. If less than the entire data is read or written, the next read/write continues where the previous one ended; this call and AX=4402h both reset the location at which the next operation starts to zero v2.1+ uses a new configuration method, but allows the installation of IPCUST.SYS for backward compatibility with other software which must read the PC/TCP configuration SeeAlso: AH=3Fh"IPCUST",AH=40h"IPCUST",AX=4402h"IPCUST" --------V-214403----------------------------- INT 21 - Compaq AG1024.SYS - CPQ_MGES - IOCTL OUTPUT AX = 4403h BX = file handle referencing device "CPQ_MGES" DS:DX -> request packet (see #0747) CX ignored Return: CF clear if successful AX destroyed data buffer filled (if applicable) first word of request packet set to number of bytes of data available (amount returned is smaller of this and requested amount) CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: AG1024.SYS is a device driver for the Advanced Graphics 1024 adapter SeeAlso: AX=4403h"RGDI" Format of Compaq AG1024.SYS request packet: Offset Size Description (Table 0747) 00h WORD function 0000h get ??? (26h bytes) 0001h get ??? (36h bytes) 0002h set ??? (same as returned by function 0001h) 0003h get ??? (6 bytes) 0004h get ??? 0005h get ??? 0006h get ??? (10h bytes) 0007h set ??? (same as returned by function 0006h) ---functions 00h-03h,06h,07h--- 02h WORD size of data buffer 04h DWORD -> buffer for function's data ---functions 04h,05h--- 02h WORD ??? 04h WORD size of data buffer 06h DWORD -> buffer to receive data --------V-214403----------------------------- INT 21 - Compaq AG1024.SYS - RGDI - IOCTL OUTPUT AX = 4403h BX = file handle referencing device "$$$$RGDI" DS:DX -> request packet (see #0748) CX ignored Return: CF clear if successful AX destroyed data buffer filled (if applicable) first word of request packet set to number of bytes of data available (amount returned is smaller of this and requested amount) CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: AG1024.SYS is a device driver for the Advanced Graphics 1024 adapter SeeAlso: AX=4402h"RGDI",AX=4403h"CPQ_MGES" Format of Compaq AG1024.SYS request packet: Offset Size Description (Table 0748) 00h WORD function 0000h get entry points 0001h get ??? 02h DWORD address of buffer for returned data --------m-214403SF01------------------------- INT 21 U - Qualitas 386MAX v6.01+ - TURN 386MAX OFF AX = 4403h subfn 01h BX = handle for device "386MAX$$" DS:DX -> BYTE 01h CX ignored Return: DS:DX -> BYTE status (00h = successful) CF clear if successful AX destroyed CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: this function will fail if any EMS or UMBs are in use SeeAlso: AX=4403h/SF=02h,AX=4403h/SF=03h,AX=4403h/SF=05h --------m-214403SF02------------------------- INT 21 U - Qualitas 386MAX v6.01+ - TURN 386MAX ON AX = 4403h subfn 02h BX = handle for device "386MAX$$" DS:DX -> BYTE 02h CX ignored Return: DS:DX -> BYTE status (00h = successful) CF clear if successful AX destroyed CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4403h/SF=01h,AX=4403h/SF=03h,AX=4403h/SF=05h --------m-214403SF03------------------------- INT 21 U - Qualitas 386MAX v6.01+ - SET STATE AX = 4403h subfn 03h BX = handle for device "386MAX$$" CX = number of bytes to copy (up to size of state buffer) DS:DX -> BYTE 03h followed by state buffer (see #0687 at AX=4402h"386MAX") Return: CF clear if successful AX = number of bytes actually written CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: the first byte of the buffer must be either 01h, 02h, or 03h (specifying the version of the state record) and the buffer must contain CX bytes AFTER the initial byte SeeAlso: AX=4402h"386MAX" --------m-214403SF05------------------------- INT 21 U - Qualitas 386MAX v7.00+ - LIMIT AUTOMATIC ACTIVATION TO STD EMS CALLS AX = 4403h subfn 05h BX = handle for device "386MAX$$" DS:DX -> BYTE 05h CX ignored Return: CF clear if successful AX destroyed CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Desc: specifies that 386MAX will only shift from AUTO to ON mode on standard EMS calls INT 67/AH=40h-5Dh SeeAlso: AX=4403h/SF=02h,AX=4403h/SF=03h,AX=4403h/SF=06h --------m-214403SF06------------------------- INT 21 U - Qualitas 386MAX v7.00+ - ALLOW AUTOMATIC ACTIVATION ON ANY INT 67 AX = 4403h subfn 06h BX = handle for device "386MAX$$" DS:DX -> BYTE 06h CX ignored Return: CF clear if successful AX destroyed CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Desc: specified that 386MAX should shift from AUTO to ON mode on any INT 67 call other than INT 67/AH=3Fh SeeAlso: AX=4403h/SF=01h,AX=4403h/SF=03h,AX=4403h/SF=05h --------n-214403----------------------------- INT 21 U - PenDOS PENDEV.SYS - ??? AX = 4403h BX = file handle for device "$$PENDOS" or "$$PD_REG" CX = size of buffer DS:DX -> buffer containing ??? Return: CF clear if successful buffer filled CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: A limited version of PenDOS by Communication Intelligence Corporation, which provides pen capability to keyboard-based programs, is bundled with IBM DOS 6.1 Note: this call sets the WORD at offset 1Ah into the device driver request header used to call the driver to 0000h. SeeAlso: AX=4402h"PENDEV.SYS" --------D-214404----------------------------- INT 21 - DOS 2+ - IOCTL - READ FROM BLOCK DEVICE CONTROL CHANNEL AX = 4404h BL = drive number (00h = default, 01h = A:, etc.) CX = number of bytes to read DS:DX -> buffer Return: CF clear if successful AX = number of bytes actually read CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: format of data is driver-specific SeeAlso: AX=4402h,AX=4405h,INT 2F/AX=122Bh --------k-214404----------------------------- INT 21 - Stacker - GET DEVICE DRIVER ADDRESS AND SET VOLUME NUMBER AX = 4404h BL = drive number (00h = default, 01h = A:, etc.) CX = 0004h DS:DX -> DWORD buffer to receive device driver address Return: buffer filled with pointer into Stacker device driver (see #1341): driver + 19h if Stacker Anywhere controls this drive driver + 1Ah if Stacker controls this drive unchanged else Notes: in addition to returning the address of the Stacker device driver, this call also sets the volume number at offset 58h in the device driver (see #1341 at INT 25/AX=CDCDh) Stacker Anywhere does not link its built-in device driver into the standard device driver chain, but it can be found via CDS/DPB this call can be used as an installation check for all versions of Stacker and Stacker Anywhere to avoid the INT 25 call SeeAlso: AX=4408h,AX=440Eh,AH=52h,INT 25/AX=CDCDh --------k-214404----------------------------- INT 21 - Stacker - GET STACVOL FILE SECTORS AX = 4404h BL = drive number (0 is current drive) CX = byte count (i.e., 200h = 1 sector) DS:DX -> buffer (see #0749) Return: Data Buffer contains the number of sectors requested from the STACVOL physical file for the drive specified. Format of Stacker buffer: Offset Size Description (Table 0749) 00h WORD 01CDh 02h WORD sector count 04h DWORD number of starting sector 08h DWORD far pointer to Data Buffer --------k-214404----------------------------- INT 21 - DUBLDISK.SYS v2.6 - GET INFO AX = 4404h BL = drive number of DoubleDisk drive (00h = default, 01h = A:, etc.) CX = number of bytes (000Ah-0014h, call ignored otherwise) DS:DX -> data record (see #0750) Return: CF clear if successful AX = number of bytes read CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: DUBLDISK.SYS is the device driver portion of DoubleDisk, a disk expander by Vertisoft Systems, Inc. Note: the installation check for v2.6 consists of scanning memory for the signature "FAT 2.6 byte:", which is immediately followed by a data table (see #0751) BUG: VOPT (a disk optimizer by Golden Bow Software) assumes that any driver which returns the "correct" number of bytes when the first word of the buffer for the data record contains the signature value 4444h is DoubleDisk; a workaround is for the non-DoubleDisk driver to return no data if the signature is present SeeAlso: AX=440Dh Index: installation check;DUBLDISK.SYS Format of DUBLDISK data record: Offset Size Description (Table 0750) 00h WORD (call) signature 4444h 02h BYTE (call) function 00h ??? 01h ??? ---function 00h--- 02h BYTE (ret) ??? 03h BYTE (ret) ??? ---function 01h--- 02h WORD (ret) 4444h 04h WORD allocation unit size??? 06h WORD ??? 08h WORD ??? 0Ah BYTE ??? Format of DUBLDISK signature data table: Offset Size Description (Table 0751) 00h 5 BYTEs ??? 05h BYTE first drive number 06h BYTE number of drives 07h ??? --------k-214404----------------------------- INT 21 - DBLSPACE.BIN - IOCTL - FLUSH OR INVALIDATE INTERNAL CACHES AX = 4404h BL = drive number (00h = default, 01h = A:, etc) CX = 000Ah (size of DSPACKET structure) DS:DX -> DSPACKET structure (see #0752) Return: CF clear if IOCTL successful -- check DSPACKET for actual status AX = number of bytes actually transferred CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4405h"DBLSPACE",INT 2F/AX=4A11h/BX=0000h Format of DoubleSpace DSPACKET structure: Offset Size Description (Table 0752) 00h WORD signature 444Dh ("DM") 02h BYTE command code 46h ('F') flush internal caches 49h ('I') flush and invalidate internal caches 03h WORD result code (ret) 4F4Bh ("OK") if successful, else unchanged 05h 5 BYTEs padding --------k-214404----------------------------- INT 21 - DBLSPACE.BIN v6.2 - IOCTL - GET ??? FOR SPECIFIED DRIVE AX = 4404h BL = drive number (00h = default, 01h = A:, etc) CX = size of DSPACKET structure (ignored in DOS 6.2) DS:DX -> DSPACKET structure (see #0753) Return: CF clear if IOCTL successful -- check DSPACKET for actual status AX = number of bytes actually transferred CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4405h"DBLSPACE",INT 2F/AX=4A11h/BX=0000h Format of DoubleSpace DSPACKET structure: Offset Size Description (Table 0753) 00h WORD signature 444Dh ("DM") 02h BYTE command code 53h ('S') get ??? for specified drive 03h WORD result code (ret) 4F4Bh ("OK") if successful, else unchanged 05h DWORD (ret) pointer to 96-byte ??? data 09h DWORD (ret) pointer to ??? data 0Dh 3 BYTEs reserved --------k-214404----------------------------- INT 21 U - DoubleTools v1.0 - GET ??? AX = 4404h BL = drive number (00h = default, 01h = A:, etc) CX = 0006h DS:DX -> DoubleTools structure (see #0754) Return: CF clear if IOCTL successful -- check DSPACKET for actual status AX = number of bytes actually transferred CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: the Transporter device driver has the signature 55h 61h 50h 74h ("DaPt") twelve bytes after it beginning Format of DoubleTools structure: Offset Size Description (Table 0754) 00h WORD (call) signature 55h AAh (ret) signature 78h 70h ("xp") 02h WORD (call) signature 52h 16h (ret) ??? 04h WORD (ret) segment of driver's DS (same as its PSP) --------d-214404----------------------------- INT 21 U - xDISK v3.31 - CONFIGURE AX = 4404h BL = drive number (00h = default, 01h = A:, etc) CX = 0047h (length of version string) DS:DX -> 79-byte buffer for version string and ??? DS:0081h = commandline containing new switches for driver Return: CF clear if successful AX = number of bytes actually transferred CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: xDISK is a shareware resizeable EMS RAMdisk by FM de Monasterio SeeAlso: AX=4405h"xDISK",INT 2F/AH=DDh/BX=7844h"xDISK" --------c-214404----------------------------- INT 21 - COMBI-disk v1.13 - GET DATA RECORD AX = 4404h BL = drive number (00h = default, 01h = A:, etc) CX = 0032h (length of data packet) DS:DX -> buffer for data packet (see #0755) Return: CF clear if successful AX = number of bytes actually transferred CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: COMBI-disk is a shareware combination cache and RAMdisk sharing a single pool of memory by Vadim V. Vlasov Note: the installation check consists of scanning the valid drives for one which returns a correctly-sized data packet with the proper signature in the first field SeeAlso: AX=4405h"COMBI" Index: installation check;COMBI-disk Format of COMBI-disk data packet: Offset Size Description (Table 0755) 00h 6 BYTEs ASCIZ signature "COMBI" 06h WORD version (high byte = major, low = decimal minor version) 08h BYTE current options (see below) 09h BYTE sectors per allocation block 0Ah WORD maximum buffer in KB 0Ch WORD current buffer in KB (less than max if XMS memory being lent) 0Eh WORD total number of allocation blocks 10h WORD current number of allocation blocks 12h WORD number of blocks being used by RAM disk 14h WORD number of blocks being used by cache or unused 16h WORD number of dirty cache blocks 18h WORD number of blocks which could not be written out due to errors 1Ah WORD total number of read requests 1Ch WORD total number of sectors read 1Eh WORD number of BIOS read requests (cache misses) 20h WORD number of sectors read via BIOS (cache misses) 22h WORD total number of write requests 24h WORD total number of sectors written 26h WORD number of BIOS write requests 28h WORD number of sectors written via BIOS 2Ah WORD number of RAM disk read requests 2Ch WORD number of sectors read from RAM disk 2Eh WORD number of RAM disk write requests 30h WORD number of sectors written to RAM disk --------d-214404----------------------------- INT 21 - SFS v1.00 - GET CONFIGURATION INFORMATION AX = 4404h BL = drive number (00h = default, 01h = A:, etc) CX = 001Ah (length of data packet) DS:DX -> buffer for data packet (see #0756) Return: CF clear if successful AX = number of bytes actually transferred CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: SFS (Secure FileSystem) is a shareware encrypting disk driver by Peter C. Gutmann SeeAlso: AX=4405h"SFS" Format of SFS data packet: Offset Size Description (Table 0756) 00h 4 BYTEs signature string "SFS1" 04h WORD SFS unit number (0-based) 06h WORD drive on which the SFS volume is mounted 08h DWORD sector offset of logical volume from start of physical volume 0 if logical volume = physical volume 0Ch WORD flag: 00h = no disk mounted, 01h = disk mounted 0Eh WORD flag: 00h read/write, 01h read-only 10h WORD quick-unmount hotkey (high byte = shift state, low = scan code) 12h WORD auto-unmount time in minutes, or 0000h if already expired, or FFFFh if not set 14h WORD time in minutes remaining before auto-unmount 16h WORD internal driver check code 0000h no error 0001h driver consistency check failed 0002h unit consistency check failed 18h WORD disk access mode 0000h BIOS 0001h IDE direct access 0002h SCSI direct access --------D-214405----------------------------- INT 21 - DOS 2+ - IOCTL - WRITE TO BLOCK DEVICE CONTROL CHANNEL AX = 4405h BL = drive number (00h = default, 01h = A:, etc) CX = number of bytes to write DS:DX -> data to write Return: CF clear if successful AX = number of bytes actually written CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: format of data is driver-specific SeeAlso: AX=4403h,AX=4404h,INT 2F/AX=122Bh --------d-214405----------------------------- INT 21 - Brian Antoine Seagate ST-01 SCSI.SYS - IOCTL - EXECUTE COMMANDS AX = 4405h BX = drive number (00h = default, 01h = A:, etc) CX = number of bytes to write DS:DX -> SCSIDISK control block (see also #0745 at AX=4403h"ST-01") Return: CF clear if successful AX = number of bytes actually written CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4403h"ST-01" --------k-214405----------------------------- INT 21 U - DBLSPACE.BIN - IOCTL - FLUSH OR INVALIDATE INTERNAL CACHES AX = 4405h BL = drive number (00h = default, 01h = A:, etc) CX = 000Ah (size of DSPACKET structure) DS:DX -> DSPACKET structure (see #0757) Return: CF clear if IOCTL successful -- check DSPACKET for actual status AX = number of bytes actually transferred CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: this call is identical to the documented AX=4404h SeeAlso: AX=4404h"DBLSPACE",INT 2F/AX=4A11h/BX=0000h Format of DoubleSpace DSPACKET structure: Offset Size Description (Table 0757) 00h WORD signature 444Dh ("DM") 02h BYTE command code 46h ('F') flush internal caches 49h ('I') flush and invalidate internal caches 03h WORD result code (ret) 4F4Bh ("OK") if successful, else unchanged 05h 5 BYTEs padding --------d-214405----------------------------- INT 21 U - xDISK v3.31 - ??? AX = 4405h BL = drive number (00h = default, 01h = A:, etc) CX = number of bytes to write DS:DX -> buffer containing version string ??? Return: CF clear if successful AX = number of bytes actually transferred CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: xDISK is a shareware resizeable EMS RAMdisk by FM de Monasterio SeeAlso: AX=4404h"xDISK",INT 2F/AH=DDh/BX=7844h"xDISK" --------d-214405----------------------------- INT 21 - COMBI-disk v1.13 - CONTROL COMBI-disk AX = 4405h BL = drive number (00h = default, 01h = A:, etc) for RAM disk CX = number of bytes to write DS:DX -> buffer containing command packet (see #0759) Return: CF clear if successful AX = number of bytes actually transferred CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) SeeAlso: AX=4404h"COMBI" (Table 0758) Values for COMBI-disk command code: 80h flush cache 81h change options byte 82h shrink memory 83h expand memory 84h get dirty block information 85h reset write errors 86h reset counters Format of COMBI-disk command packet: Offset Size Description (Table 0759) 00h WORD version 02h BYTE command code (see #0758) ---command code 80h--- no additional fields ---command code 81h--- 03h BYTE new options byte (see #0760) ---command code 82h--- 03h WORD number of KB to release ---command code 83h--- 03h WORD number of KB to expand ---command code 84h--- 03h DWORD -> buffer for block info (see #0761) ---command code 85h--- 03h DWORD block ID ---command code 86h--- 03h BYTE which counters to reset bit 0: hard disk read counts bit 1: hard disk write counts bit 2: RAM disk read/write counts Note: multiple commands may be placed in a single packet by stringing together as many command/argument pairs as desired Bitfields for COMBI-disk options byte: Bit(s) Description (Table 0760) 0 cache off 1 cache frozen 2 write caching enabled 3 delayed writing disabled 5 fix memory allocation (no XMS lending) 6 no 'sector not found' error Format of COMBI-disk block info: Offset Size Description (Table 0761) 00h DWORD block ID 04h BYTE bitmask of valid sectors in block 05h BYTE bitmask of dirty sectors in block 06h BYTE last error returned by BIOS 07h BYTE number of errors --------D-214405----------------------------- INT 21 - SFS v1.00 - DRIVER CONTROL AX = 4405h BL = drive number (00h = default, 01h = A:, etc) CX = number of bytes to write DS:DX -> data to write (see #0763) Return: CF clear if successful AX = number of bytes actually written CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Program: SFS (Secure FileSystem) is a shareware encrypting disk driver by Peter C. Gutmann SeeAlso: AX=4404h"SFS" (Table 0762) Values for SFS control function: 00h "PACKET_SET_DISKINFO" set disk parameters 01h "PACKET_SET_KEYINFO" set keying information 02h "PACKET_SET_READONLY" select read/write or read-only 03h "PACKET_SET_DRIVENO" set drive number to mount 04h "PACKET_SET_MOUNTSTATUS" set mount status 05h "PACKET_SET_UNMOUNT" set/clear quick-unmount hotkey 06h "PACKET_SET_TIMEOUT" set/clear auto-unmount timeout Format of SFS control data packet: Offset Size Description (Table 0763) 00h WORD signature 4330h ('C0') 02h WORD function (see #0762) ---function 00h--- 04h WORD sector size in bytes 06h BYTE sectors per cluster 07h WORD number of boot sectors 09h BYTE number of copies of FAT 0Ah WORD size of root directory in entries 0Ch WORD number of sectors on disk, 16-bit 0Eh BYTE media descriptor byte 0Fh WORD sectors per FAT 11h WORD sectors per track 13h WORD number of heads 15h DWORD number of hidden sectors 19h DWORD number of sectors on disk, 32-bit ---function 01h--- 04h 20 BYTEs master IV for encrypted disk 18h 64 BYTEs NDC/SHS keying information ---function 02h--- 04h WORD read-only state: 00h read-only, 01h read/write ---function 03h--- 04h WORD drive number (see #0764) 06h DWORD sector offset of logical volume from start of physical volume 0 if logical volume = physical volume ---function 04h--- 04h WORD mount status (00h unmounted, 01h mounted) ---function 05h--- 04h WORD hotkey (high byte = shift state, low byte = scan code or 00h) 0000h to disable hotkey ---function 06h--- 04h WORD timeout in minutes before automatic unmount 0000h to disable auto-unmount Notes: the data for function 00h corresponds to a DOS BPB (see AH=53h) functions 00h, 01h, and 03h automatically unmount the encrypted drive unmounting a drive with function 04h also destroys the encryption information in the driver and forces all dirty buffers to be flushed Bitfields for SFS drive number: Bit(s) Description (Table 0764) 15-12 drive access mode 0000 BIOS access 0001 direct IDE access 0010 direct SCSI access ---if BIOS access--- 11-8 unused (0) 7-0 BIOS drive number ---if IDE access--- 11-8 unused (0) 7-0 IDE drive number ---if SCSI access--- 11-8 SCSI host number 7-4 SCSI target ID 3-0 SCSI logical unit number --------D-214406----------------------------- INT 21 - DOS 2+ - IOCTL - GET INPUT STATUS AX = 4406h BX = file handle Return: CF clear if successful AL = input status 00h not ready (device) or at EOF (file) FFh ready CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: files may not register as being at EOF if positioned there by AH=42h SeeAlso: AX=4407h,INT 2F/AX=122Bh --------D-214407----------------------------- INT 21 - DOS 2+ - IOCTL - GET OUTPUT STATUS AX = 4407h BX = file handle Return: CF clear if successful AL = input status 00h not ready FFh ready CF set on error AX = error code (01h,05h,06h,0Dh) (see #0885 at AH=59h) Note: for DOS 2+, files are always ready for output, even if the disk is full or no media is in the drive SeeAlso: AX=4406h,INT 2F/AX=122Bh --------D-214408----------------------------- INT 21 - DOS 3.0+ - IOCTL - CHECK IF BLOCK DEVICE REMOVABLE AX = 4408h BL = drive number (00h = default, 01h = A:, etc) Return: CF clear if successful AX = media type (0000h removable, 0001h fixed) CF set on error AX = error code (01h,0Fh) (see #0885 at AH=59h) Note: in addition to the normal operation, if Stacker is installed, this call also sets the volume number at offset 58h in the Stacker device driver (except under DR-DOS 3.41-5.0, which do not pass through this call to the driver; use AX=440Eh instead) (see AX=4404h"Stacker",AX=440Eh,INT 25/AX=CDCDh) SeeAlso: AX=4400h,AX=4404h"Stacker",AX=4409h,INT 2F/AX=122Bh --------D-214409----------------------------- INT 21 - DOS 3.1+ - IOCTL - CHECK IF BLOCK DEVICE REMOTE AX = 4409h BL = drive number (00h = default, 01h = A:, etc) Return: CF clear if successful DX = device attribute word bit 15: drive is SUBSTituted bit 12: drive is remote bit 9: direct I/O not allowed CF set on error AX = error code (01h,0Fh) (see #0885 at AH=59h) Note: on local drives, DX bits not listed above are the attribute word from the device driver header (see #0858 at AH=52h); for remote drives, the other bits appear to be undefined for DOS versions prior to 5.0 (they are all cleared in DOS 5+) checking whether DX=0800h on return appears to be a fairly reliable method for detecting Microsoft's RAMDRIVE, though not for other ramdisks (there appears to be no simple yet foolproof method for detecting ramdisks, although the presence of only a single copy of the FAT and only a single head on non-removable devices is a fairly good indicator) SeeAlso: AX=4400h,AX=4408h,AX=440Ah,INT 2F/AX=122Bh --------D-21440A----------------------------- INT 21 - DOS 3.1+ - IOCTL - CHECK IF HANDLE IS REMOTE AX = 440Ah BX = handle Return: CF clear if successful DX = attribute word (as stored in SFT) bit 15: set if remote bit 14: date/time not set on close CF set on error AX = error code (01h,06h) (see #0885 at AH=59h) Notes: if file is remote, Novell Advanced NetWare 2.0 returns the number of the file server on which the handle is located in CX DR-DOS 3.41 and 5.0 clear all bits of DX except bit 15 SeeAlso: AX=4400h,AX=4409h,AH=52h,INT 2F/AX=122Bh --------D-21440B----------------------------- INT 21 - DOS 3.1+ - IOCTL - SET SHARING RETRY COUNT AX = 440Bh CX = pause between retries (default 1) DX = number of retries (default 3) Return: CF clear if successful CF set on error AX = error code (01h) (see #0885 at AH=59h) Notes: delay is dependent on processor speed (value in CX specifies number of 64K-iteration empty loops to execute) if DX=0000h on entry, the retry count is left unchanged SeeAlso: AH=52h,INT 2F/AX=1224h,INT 2F/AX=122Bh --------D-21440C----------------------------- INT 21 - DOS 3.2+ - IOCTL - GENERIC CHARACTER DEVICE REQUEST AX = 440Ch BX = device handle CH = category code (see #0765) CL = function number (see #0766) DS:DX -> parameter block (see #0767,#0768,#0769,#0770,#0771,#0772) SI = parameter to pass to driver (European MS-DOS 4.0, OS/2 comp box) DI = parameter to pass to driver (European MS-DOS 4.0, OS/2 comp box) Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful DS:DX -> iteration count if CL=65h SI = returned value (European MS-DOS 4.0, OS/2 comp box) DI = returned value (European MS-DOS 4.0, OS/2 comp box) Note: DR-DOS 3.41 and 5.0 return error code 16h on CL=45h,65h if the device does not support a retry counter SeeAlso: AX=440Dh,INT 2F/AX=0802h,INT 2F/AX=122Bh,INT 2F/AX=14FFh SeeAlso: INT 2F/AX=1A01h (Table 0765) Values for IOCTL category code: 00h unknown (DOS 3.3+) 01h COMn: (DOS 3.3+) 03h CON (DOS 3.3+) 05h LPTn: 9Eh Media Access Control driver (STARLITE) 00h-7Fh reserved for Microsoft 80h-FFh reserved for OEM/user-defined (Table 0766) Values for generic character IOCTL function: 00h MAC driver Bind (STARLITE) (see #0767) 45h set iteration (retry) count (see #0768) 4Ah select code page (see #0769) 4Ch start code-page preparation (see #0770) 4Dh end code-page preparation (see #0771) 5Fh set display information (DOS 4.0+) (see #0772) 65h get iteration (retry) count 6Ah query selected code page (see #0769) 6Bh query prepare list (see #0773) 7Fh get display information (DOS 4.0+) (see #0772) Note: bit assignments for function code: bit 7: set to ignore if unsupported, clear to return error bit 6: set if passed to driver, clear if intercepted by DOS bit 5: set if queries data from device, clear if sends command bits 4-0: subfunction Format of parameter block for function 00h: Offset Size Description (Table 0767) 00h 8 BYTEs ASCIZ signature "STARMAC" 08h WORD version 0Ah WORD flags bit 0: media requires connect or listen request before use bit 1: network is a LAN (broadcast/multicast supported) bit 2: point-to-point network 0Ch WORD handle for use with MAC driver's private interface (filled in by MAC driver) 0Eh WORD context 10h WORD approximate speed in KB/sec (filled in by MAC driver) 12h WORD approximate cost in cents per hour (filled in by MAC driver) 14h WORD maximum packet size in bytes (filled in by MAC driver) 16h WORD addressing format (filled in by MAC driver) 0000h general addressing 0001h Ethernet addressing 0002h Token Ring addressing 0003h Token Bus addressing 18h DWORD Send entry point (filled in by MAC driver) 1Ch DWORD RegisterEventHandler entry point (filled in by MAC driver) 20h DWORD SetPacketFilter entry point (filled in by MAC driver) 24h DWORD UnBind entry point (filled in by MAC driver) Format of parameter block for function 45h: Offset Size Description (Table 0768) 00h WORD number of times output is attempted before driver assumes device is busy Format of parameter block for functions 4Ah and 6Ah: Offset Size Description (Table 0769) 00h WORD length of data 02h WORD code page ID 04h 2N BYTEs DCBS (double byte character set) lead byte range start/end for each of N ranges (DOS 4.0) WORD 0000h end of data (DOS 4.0) Format of parameter block for function 4Ch: Offset Size Description (Table 0770) 00h WORD flags DISPLAY.SYS = 0000h PRINTER.SYS bit 0 clear to prepare downloaded font, set to prepare cartridge selection 02h WORD length of remainder of parameter block 04h WORD number of code pages following 06h N WORDs code page 1,...,N Format of parameter block for function 4Dh: Offset Size Description (Table 0771) 00h WORD length of data 02h WORD code page ID Format of parameter block for functions 5Fh and 7Fh: Offset Size Description (Table 0772) 00h BYTE level (0 for DOS 4.x-6.0) 01h BYTE reserved (0) 02h WORD length of following data (14) 04h WORD control flags bit 0 set for blink, clear for intensity bits 1-15 reserved 06h BYTE mode type (1=text, 2=graphics) 07h BYTE reserved (0) 08h WORD colors 0000h = monochrome else N bits per pixel 0Ah WORD pixel columns 0Ch WORD pixel rows 0Eh WORD character columns 10h WORD character rows Format of parameter block for function 6Bh: Offset Size Description (Table 0773) 00h WORD length of following data 02h WORD number of hardware code pages 04h N WORDs hardware code pages 1,...,N WORD number of prepared code pages N WORDs prepared code pages 1,...,N --------d-21440C----------------------------- INT 21 - Greg Shenaut ASPITAPE.SYS - INTERFACE AX = 440Ch BX = device handle CH = category code 07h tape (ASPITAPE.SYS) CL = function 01h "mtop" - perform tape operation 02h "mtget" - get tape status 03h ignore end-of-tape errors 04h enable end-of-tape errors DS:DX -> parameter block (see #0774,#0775) Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful DS:DX -> data block Notes: This device driver is a simple DOS interface to the Adaptec Advanced SCSI Programming Interface (ASPI). It provides the following device names as access to the SCSI tape, 'RMTx' (rewind on close) and 'NRMTx' (NO rewind on close) where x can go from 0 to 3. There may also be the following names 'MTx' and 'NMTx' which default to 1024 byte blocks. The names may also have a '$' appended to try and make them unique from file names of 'RMT0' etc. once opend these devices must be put into RAW mode SeeAlso: AX=4402h"ASPI" Format of ASPITAPE.SYS mtop parameter block: Offset Size Description (Table 0774) 00h WORD operation code 00h "MTWEOF" - write an end-of-file record 01h "MTFSF" - forward space file 02h "MTBSF" - backward space file 03h "MTFSR" - forward space record 04h "MTBSR" - backward space record 05h "MTREW" - rewind 06h "MTOFFL" - rewind and unload 07h "MTNOP" - perform TEST UNIT READY 02h DWORD repetition count Format of ASPITAPE.SYS mtget parameter block: Offset Size Description (Table 0775) 00h BYTE ASPI host ID 01h BYTE SCSI target ID 02h BYTE SCSI logical unit number 03h BYTE device parameters bit 0: drive must use fixed-block read and write bit 7: drive is an ASPI device 04h BYTE current device state (see #0776) 05h BYTE unit number within driver 06h WORD fixed block blocksize 08h BYTE last SCSI status 09h BYTE last SCSI sense key 0Ah WORD last SCSI opcode (packed) (see #0777) 0Ch WORD residual bytes from SCSI opcode Bitfields for ASPITAPE.SYS current device state: Bit(s) Description (Table 0776) 0 device currently opened in buffered mode 1 drive currently opened in nonbuffered mode 2 rewind drive on last close 3 drive has been written on 4 drive has been read from 5 next read will return 0 bytes 6 EOM will resemble EOF 7 drive may be busy rewinding Bitfields for SCSI opcode: Bit(s) Description (Table 0777) 0-7 SCSI operation (SCSI packet byte 0) 8-10 SCSI flags (SCSI packet byte 1) 11-12 ASPI "Direction Bits" (ASPI SRB byte 3) --------D-21440D----------------------------- INT 21 - DOS 3.2+ - IOCTL - GENERIC BLOCK DEVICE REQUEST AX = 440Dh BL = drive number (00h=default,01h=A:,etc) CH = category code (see #0778) CL = minor code (function) (see #0779) DS:DX -> (DOS) parameter block (see #0780,#0782,#0783,#0784,#0785) SI:DI -> (OS/2 comp box) parameter block (see #0786,#0788,#0789,#0790) Return: CF set on error AX = error code (01h,02h) (see #0885 at AH=59h) CF clear if successful DS:DX -> data block if CL=60h or CL=61h Notes: DOS 4.01 seems to ignore the high byte of the number of directory entries in the BPB for diskettes. functions 46h and 66h undocumented in DOS 4.x, documented for DOS 5+ the DUBLDISK.SYS v2.6 driver only supports minor codes 60h and 67h DR-DOS 3.41-6.0 only support minor codes 40h-42h and 60h-62h; all other minor codes return error code 16h some PCMCIA calls reportedly appear to be dangerous for MS-DOS versions prior to 5.0 minor code 60h normally produces no I/O except with AutoMount=1 for DBLSPACE/DRVSPACE SeeAlso: AX=440Ch,AH=69h,INT 2F/AX=0802h,INT 2F/AX=122Bh (Table 0778) Values for block device IOCTL category code: 08h disk drive 00h-7Fh reserved for Microsoft 80h-FFh reserved for OEM/user-defined (Table 0779) Values for generic block IOCTL minor code: 00h (OS/2) \ used to lock/unlock a drive 01h (OS/2) / 40h set device parameters (see #0780) 41h write logical device track (see #0782) 42h format and verify logical device track (see #0783) 46h (DOS 4.0+) set volume serial number (see #0785,AH=69h) 47h (DOS 4.0+) set access flag (see #0786) 48h (Enh. Disk Drive Spec) set media lock state (see #0787,INT 13/AH=45h) 49h (Enh. Disk Drive Spec) eject media in drive (see INT 13/AH=49h) 50h (PCMCIA) attribute memory write 51h (PCMCIA) common memory write 52h (PCMCIA) force media change (DOS 5+ ???) (see #0788) 53h (PCMCIA) erase drive 54h (PCMCIA) erase media 56h (PCMCIA) set erase status callback 57h (PCMCIA) append Card Information Structure (CIS) tuple 58h (PCMCIA) erase CIS tuples 60h get device parameters (see #0780) 61h read logical device track (see #0782) 62h verify logical device track (see #0784) 66h (DOS 4.0+) get volume serial number (see #0785,AH=69h) 67h (DOS 4.0+) get access flag (see #0786) 68h (DOS 5.0+) sense media type (see #0789) 70h (PCMCIA) attribute memory read 73h (PCMCIA) get memory media information (DOS 5+ ???) (see #0790) 76h (PCMCIA) get erase status callback 77h (PCMCIA) get first Card Information Structure (CIS) tuple 78h (PCMCIA) get next CIS tuple 7Fh (PCMCIA) get ??? information (see #0791,#0792) Format of parameter block for functions 40h, 60h: Offset Size Description (Table 0780) 00h BYTE special functions bit 0 set if function to use current BPB, clear if Device BIOS Parameter Block field contains new default BPB bit 1 set if function to use track layout fields only must be clear if CL=60h bit 2 set if all sectors in track same size (should be set) bits 3-7 reserved 01h BYTE device type (see #0781) 02h WORD device attributes bit 0 set if nonremovable medium bit 1 set if door lock ("changeline") supported bits 2-15 reserved 04h WORD number of cylinders 06h BYTE media type for 1.2M drive 00h 1.2M disk (default) 01h 320K/360K disk F8h for DUBLDISK.SYS v2.6 expanded drives always 00h for other drive types 07h 31 BYTEs device BPB (see #0875 at AH=53h), bytes after BPB offset 1Eh omitted ---function 40h only--- 26h WORD number of sectors per track (start of track layout field) (maximum 63) 28h N word pairs: number,size of each sector in track (Table 0781) Values for device type: 00h 320K/360K disk 01h 1.2M disk 02h 720K disk 03h single-density 8-inch disk 04h double-density 8-inch disk 05h fixed disk 06h tape drive 07h (DOS 3.3+) other type of block device, normally 1.44M floppy 08h read/write optical disk 09h (DOS 5+) 2.88M floppy Format of parameter block for functions 41h, 61h: Offset Size Description (Table 0782) 00h BYTE special functions (reserved, must be zero) 01h WORD number of disk head 03h WORD number of disk cylinder 05h WORD number of first sector to read/write 07h WORD number of sectors 09h DWORD transfer address Format of parameter block for function 42h: Offset Size Description (Table 0783) 00h BYTE reserved, must be zero (DOS <3.2) bit 0=0: format/verify track 1: format status call (DOS 3.2+), don't actually format bits 1-7 reserved, must be zero value on return (DOS 3.3+): 00h specified tracks, sectors/track supported by BIOS 01h function not supported by BIOS 02h specified tracks, sectors/track not allowed for drive 03h no disk in drive 01h WORD number of disk head 03h WORD number of disk cylinder Format of parameter block for function 62h: Offset Size Description (Table 0784) 00h BYTE reserved, must be zero (DOS <3.2) bit 0=0: verify single track 1: verify multiple tracks bits 1-7 reserved, must be zero value on return (DOS 3.3+): 00h specified tracks, sectors/track supported by BIOS 01h function not supported by BIOS 02h specified tracks, sectors/track not allowed for drive 03h no disk in drive 01h WORD number of disk head 03h WORD number of disk cylinder 05h WORD number of tracks to verify (equivalent to 255 or fewer sectors) Format of parameter block for functions 46h, 66h: Offset Size Description (Table 0785) 00h WORD (call) info level (should be 0000h) 02h DWORD disk serial number (binary) 06h 11 BYTEs volume label or "NO NAME " 11h 8 BYTEs filesystem type "FAT12 " or "FAT16 " (CL=66h only) Format of parameter block for functions 47h, 67h: Offset Size Description (Table 0786) 00h BYTE special-function field (must be zero) 01h BYTE disk-access flag, nonzero if access allowed by driver Format of parameter block for function 48h: Offset Size Description (Table 0787) 00h BYTE (call) locking operation 00h lock media in drive 01h unlock media 02h get locking status 01h BYTE (ret) drive's lock status Format of parameter block for function 52h: 00h BYTE (call) unused??? (Table 0788) (ret) 00h if flash/ATA drive but no card inserted unchanged otherwise Notes: the absense of a flash card should be tested by checking the DOS error code rather than the returned byte the parameter byte is cleared to 00h erroneously by the Award PCDISK.EXE v1.02c PCMCIA/ATA driver if no ATA card is inserted (bug corrected in PCDISK.EXE v1.02h and later) not supported by the SystemSoft ATADRV.EXE and the Phoenix PCMATA.SYS PCMCIA/ATA drivers Format of parameter block for function 68h: Offset Size Description (Table 0789) 00h BYTE 01h for default media type, 00h for any other media type (see also INT 13/AH=20h"Compaq") 01h BYTE 02h for 720K, 07h for 1.44M, 09h for 2.88M Format of parameter block for function 73h: Offset Size Description (Table 0790) 00h BYTE ??? 00h ATA card inserted ??? 80h ATA card not inserted ??? 01h BYTE length of parameter block ??? apparently always 40h 02h BYTE ??? 00h ATA card not inserted ??? 0Dh ATA card inserted ??? 03h 2 BYTEs ??? (apparently always 00h) 05h BYTE drive number (0=first) ??? 06h BYTE total number of drives ??? 07h BYTE ??? 00h ATA card not inserted ??? 01h ATA card inserted ??? 08h 17 BYTEs ??? 19h BYTE ??? 00h ATA card not inserted ??? 01h ATA card inserted ??? 1Ah BYTE ??? (apparently always 01h) 1Bh BYTE ??? 00h ATA card not inserted ??? 01h ATA card inserted ??? 1Ch 2 BYTEs ??? (apparently always 0015h) 1Eh 2 BYTEs ??? 20h 2 BYTEs ??? (apparently always 0110h) 22h 15 BYTEs ??? 31h 2 BYTEs ??? (apparently always 7000h) 33h 11 BYTEs driver signature "AWARD PDISK" for Award PCDISK.EXE PCMCIA/ATA driver "MS-BIOS " for HP 200LX generic ATA driver 3Eh 2 BYTEs ??? Notes: parameter structure possibly depends on driver this function is not supported by the SystemSoft ATADRV.EXE and the Phoenix PCMATA.SYS PCMCIA/ATA drivers Format of parameter block for function 7Fh for SystemSoft ATADRV.EXE: Offset Size Description (Table 0791) 00h DWORD -> unknown location within driver Note: function supported by the SystemSoft ATADRV.EXE PCMCIA/ATA driver but not by the Award PCDISK.EXE PCMCIA/ATA driver SeeAlso: #0792 Format of parameter block for function 7Fh for Phoenix PCMATA.SYS: Offset Size Description (Table 0792) 00h 8 BYTEs ??? Note: this function supported by the Phoenix PCMATA.SYS PCMCIA/ATA driver but not by the Award PCDISK.EXE PCMCIA/ATA driver SeeAlso: #0791 --------D-21440E----------------------------- INT 21 - DOS 3.2+ - IOCTL - GET LOGICAL DRIVE MAP AX = 440Eh BL = drive number (00h=default,01h=A:,etc) Return: CF set on error AX = error code (01h,0Fh) (see #0885 at AH=59h) CF clear if successful AL = 00h block device has only one logical drive assigned 1..26 the last letter used to reference the drive (1=A:,etc) Notes: DR-DOS 3.41-5.0 DRIVER.SYS does not support drive mapping and thus always returns AL=00h in addition to the normal operation, if Stacker is installed, this call also sets the volume number at offset 58h in the Stacker device driver (DR-DOS 3.41-5.0 only; use AX=4408h otherwise) (see AX=4404h"Stacker",INT 25/AX=CDCDh) SeeAlso: AX=4408h,AX=440Fh,INT 2F/AX=122Bh --------D-21440F----------------------------- INT 21 - DOS 3.2+ - IOCTL - SET LOGICAL DRIVE MAP AX = 440Fh BL = physical drive number (00h=default,01h=A:,etc)) Return: CF set on error AX = error code (01h,0Fh) (see #0885 at AH=59h) CF clear if successful drive now responds to next logical drive number Notes: maps logical drives to physical drives, similar to DOS's treatment of a single physical floppy drive as both A: and B: DR-DOS 3.41-5.0 DRIVER.SYS does not support drive mapping and thus always returns an error on this function SeeAlso: AX=440Eh,INT 2F/AX=122Bh --------D-214410----------------------------- INT 21 - DOS 5+ - IOCTL - QUERY GENERIC IOCTL CAPABILITY (HANDLE) AX = 4410h BX = handle for device CH = category code (see #0765) CL = function code (see #0766) Return: CF clear if successful AX = 0000h specified IOCTL function is supported CF set on error AL = 01h IOCTL capability not available Note: a program which wishes to use Generic IOCTL calls beyond those in the standard DOS 3.2 set may use this call first to see whether a particular call is supported SeeAlso: AX=440Ch,AX=440Dh,AX=4411h --------d-214410BXFFFF----------------------- INT 21 U - NewSpace - ENABLE DRIVER AX = 4410h BX = FFFFh Program: NewSpace is a TSR by Isogon Corporation which automatically compresses all files as they are written and decompresses them as they are read Note: compressed files are not accessible unless the driver is enabled SeeAlso: AX=4411h/BX=FFFFh --------D-214411----------------------------- INT 21 - DOS 5+ - IOCTL - QUERY GENERIC IOCTL CAPABILITY (DRIVE) AX = 4411h BL = drive number CH = category code (see #0778) CL = function code (see #0779) Return: CF clear if successful AX = 0000h specified IOCTL function is supported CF set on error AL = 01h IOCTL capability not available Note: a program which wishes to use Generic IOCTL calls beyond those in the standard DOS 3.2 set may use this call first to see whether a particular call is supported SeeAlso: AX=440Ch,AX=440Dh,AX=4410h --------d-214411BXFFFF----------------------- INT 21 U - NewSpace - DISABLE DRIVER AX = 4411h BX = FFFFh Program: NewSpace is a TSR by Isogon Corporation which automatically compresses all files as they are written and decompresses them as they are read Note: compressed files are not accessible unless the driver is enabled SeeAlso: AX=4410h/BX=FFFFh --------O-214412----------------------------- INT 21 O - DR-DOS 5.0-6.0 - DETERMINE DOS TYPE AX = 4412h CF set Return: CF set if not DR-DOS AX = error code (see #0885 at AH=59h) CF clear if DR-DOS DX = AX = version code (see #0794) Note: this obsolete call, which is no longer supported in Novell DOS 7, is identical to AX=4452h SeeAlso: AX=4452h --------d-214412BXFFFF----------------------- INT 21 U - NewSpace - INSTALLATION CHECK??? AX = 4412h BX = FFFFh Return: AX = PSP segment of NewRes (resident driver for NewSpace) BX:DX -> ??? CX = ??? SeeAlso: AX=4411h/BX=FFFFh --------d-214413BXFFFF----------------------- INT 21 U - NewSpace - GET ??? AX = 4413h BX = FFFFh Return: AX = code segment of NewRes (resident driver for NewSpace) BX = offset of ??? SeeAlso: AX=4412h/BX=FFFFh --------O-214414----------------------------- INT 21 OU - DR-DOS 5.0-6.0 - SET GLOBAL PASSWORD AX = 4414h DS:DX -> password string (blank-padded to 8 characters) Desc: Specify the master password for accessing files. Note: this obsolete call, which is no longer supported in Novell DOS 7, is identical to AX=4454h SeeAlso: AX=4454h --------d-214414BXFFFF----------------------- INT 21 U - NewSpace - DEBUGGING DUMP AX = 4414h BX = FFFFh Return: debugging dump written to X:\NEWSPACE.SMP SeeAlso: AX=4413h/BX=FFFFh,AX=44FFh/BX=FFFFh --------O-2144------------------------------- INT 21 OU - DR-DOS 5.0-6.0 - HISTORY BUFFER, SHARE, AND HILOAD CONTROL AH = 44h AL = 16h to 18h Note: these obsolete subfunctions (which are no longer supported in Novell DOS 7) are identical to AX=4456h through 4458h SeeAlso: AX=4456h,AX=4457h,AX=4458h --------O-214451----------------------------- INT 21 - Concurrent DOS v3.2+ - INSTALLATION CHECK AX = 4451h Return: CF set if not Concurrent DOS AX = error code (see #0885 at AH=59h) CF clear if successful AH = single-user/multiuser nature 10h single-user AL = operating system version ID (see #0794) 14h multiuser AL = operating system version ID (see #0793) Notes: as of Concurrent DOS/XM 5.0 (possibly earlier), the version is stored in the environment variable VER use this function if you are looking for multiuser capabilities, AX=4452h for single-user this function should never return the single-user values SeeAlso: AX=4452h,AX=4459h (Table 0793) Values for Digital Research operating system version ID: 32h Concurrent PC DOS 3.2 41h Concurrent DOS 4.1 50h Concurrent DOS/XM 5.0 or Concurrent DOS/386 1.1 60h Concurrent DOS/XM 6.0 or Concurrent DOS/386 2.0 62h Concurrent DOS/XM 6.2 or Concurrent DOS/386 3.0 66h DR Multiuser DOS 5.1 67h Concurrent DOS 5.1 --------O-214452----------------------------- INT 21 - DR-DOS 3.41+ - DETERMINE DOS TYPE/GET DR-DOS VERSION AX = 4452h ("DR") CF set Return: CF set if not DR-DOS AX = error code (see #0885 at AH=59h) CF clear if DR-DOS AX = version code AH = single-user/multiuser nature 10h single-user AL = operating system version ID (see #0794) 14h multiuser AL = operating system version ID (see #0793) DX modified (see note) Notes: the DR-DOS version is stored in the environment variable VER use this function if looking for single-user capabilities, AX=4451h if looking for multiuser; this call should never return multiuser values in DR-DOS 3.41-6.0, DX=AX on return; for Novell DOS 7, DH=AH but DL=00h (reportedly, DH=00h when booting NWDOS7 from installation disks) Novell DOS 7 returns error code 0001h if SETVER 255.x is in effect for the calling program SeeAlso: AX=4412h,AX=4451h,AX=4459h (Table 0794) Values for Digital Research operating system version ID: 60h DOS Plus 63h DR-DOS 3.41 64h DR-DOS 3.42 65h DR-DOS 5.00 67h DR-DOS 6.00 70h PalmDOS 71h DR-DOS 6.0 March 1993 "business update" 72h Novell DOS 7.0 --------O-214454----------------------------- INT 21 U - DR-DOS 3.41+ - SET GLOBAL PASSWORD AX = 4454h DS:DX -> password string (blank-padded to 8 characters) Desc: Specify the master password for accessing files. SeeAlso: AX=4303h,AX=4414h --------O-214456----------------------------- INT 21 U - DR-DOS 5.0+ - HISTORY BUFFER CONTROL AX = 4456h DL = control flags (see #0795) Return: AL = previous value of state flags (see #0796) Note: DR-DOS 6.0 only checks bit 0 and ignores the rest of DL SeeAlso: #0797 Bitfields for control flags: Bit(s) Description (Table 0795) 0 whose buffer: 0=application, 1=COMMAND.COM ---Novell DOS 7--- 1 toggle HISTORY usage 2 toggle INSERT state Note: only one bit at a time may be used Bitfields for state flags: Bit(s) Description (Table 0796) 0 HISTORY buffer enabled 1 INSERT enabled 2-5 unused 7 whose buffer: 0=application, 1=COMMAND.COM --------O-214457----------------------------- INT 21 U - DR-DOS 5.0+ - SHARE/HILOAD CONTROL AX = 4457h DH = subfunction 00h enable/disable SHARE DL = 00h disable = 01h enable else Return: AX = ??? 01h get HILOAD status Return: AX = status 0000h off 0001h on 02h set HILOAD status DL = new state (00h off, 01h on) Return: AX = ??? other Return: AX = ??? Note: This was seen called by COMMAND.COM of DR-DOS 6.0; it does not seem to be supported by Novell DOS 7 SeeAlso: AX=4457h/DX=FFFFh --------O-214457DXFFFF----------------------- INT 21 U - DR-DOS 6.0 - GET SHARE STATUS AX = 4457h DX = FFFFh Return: AX = SHARE status SeeAlso: INT 2F/AX=1000h --------O-214458----------------------------- INT 21 U - DR-DOS 5.0+ internal - GET POINTER TO INTERNAL VARIABLE TABLE AX = 4458h Return: ES:BX -> internal variable table (see #0797,#0798) AX = ??? (0B50h for DR-DOS 5.0, 0A56h for DR-DOS 6.0, 0FE4h for Novell DOS 7) SeeAlso: AX=4452h Format of DR-DOS 5.0-6.0 internal variable table: Offset Size Description (Table 0797) 00h WORD ??? 02h WORD segment of ??? 04h WORD offset within DOS data segment of history control structure for COMMAND.COM history buffer (see #0799) 06h WORD offset within DOS data segment of history control structure for application history buffer (see #0799) 08h BYTE initial history state flags (see #0796) 09h 2 BYTEs ??? 0Bh WORD KB of extended memory at startup 0Dh BYTE number of far jump entry points 0Eh WORD segment containing far jumps to DR-DOS entry points (see #0800) 10h WORD (only if kernel loaded in HMA) offset in HMA of first free HMA memory block (see #0801) or 0000h if none; segment is FFFFh 12h WORD pointer to segment of environment variables set in CONFIG, or 0000h if already used ---DR-DOS 6.0--- 14h WORD (only if kernel loaded in HMA) offset in HMA of first used HMA memory block (see #0801) or 0000h if none; segment is FFFFh 16h 8 BYTEs ??? 1Eh WORD offset in DOS data segment of full COUNTRY.SYS filename 20h 8 BYTEs ??? 28h WORD offset in DOS data segment of SHARE hook table 2Ah 2 BYTEs ??? 2Ch WORD offset in DOS data segment of far pointer to INT 2F/AX=1000h handler Note: the segment used for the DR-DOS 6.0 CONFIG environment variables (excluding COMSPEC, VER and OS) is only useful for programs/drivers called from CONFIG.SYS. The word is set to zero later when the area is copied to the COMMAND.COM environment space. This allows CONFIG.SYS to pass information to AUTOEXEC.BAT. Format of Novell DOS 7 internal variable table: Offset Size Description (Table 0798) 00h ??? 1Eh WORD offset of COUNTRY.SYS filename 42h 16 DWORDs pointers to ??? entry points ??? Format of history control structure: Offset Size Description (Table 0799) 00h WORD segment of buffer 02h WORD size of buffer in bytes 04h WORD ??? Format of kernel entry jump table for DR-DOS 5.0-6.0: Offset Size Description (Table 0800) 00h 5 BYTEs far jump to kernel entry point for CP/M CALL 5 05h 5 BYTEs far jump to kernel entry point for INT 20 0Ah 5 BYTEs far jump to kernel entry point for INT 21 0Fh 5 BYTEs far jump to kernel entry point for INT 22 (RETF) 14h 5 BYTEs far jump to kernel entry point for INT 23 (RETF) 19h 5 BYTEs far jump to kernel entry point for INT 24 1Eh 5 BYTEs far jump to kernel entry point for INT 25 23h 5 BYTEs far jump to kernel entry point for INT 26 28h 5 BYTEs far jump to kernel entry point for INT 27 2Dh 5 BYTEs far jump to kernel entry point for INT 28 32h 5 BYTEs far jump to kernel entry point for INT 2A (IRET) 37h 5 BYTEs far jump to kernel entry point for INT 2B (IRET) 3Ch 5 BYTEs far jump to kernel entry point for INT 2C (IRET) 41h 5 BYTEs far jump to kernel entry point for INT 2D (IRET) 46h 5 BYTEs far jump to kernel entry point for INT 2E (IRET) 4Bh 5 BYTEs far jump to kernel entry point for INT 2F Notes: all of these entry points are indirected through this jump table to allow the kernel to be relocated into high memory while leaving the actual entry addresses in low memory for maximum compatibility some of these entry points (22h,23h,24h,2Eh,2Fh) are replaced as soon as COMMAND.COM is loaded, and return immediately to the caller, some returning an error code (the original handler for INT 2F returns AL=03h [fail]). Format of HMA Memory Block (DR-DOS 6.0 kernel loaded in HMA): Offset Size Description (Table 0801) 00h WORD offset of next HMA Memory Block (0000h if last block) 02h WORD size of this block in bytes (at least 10h) 04h BYTE type of HMA Memory Block (interpreted by MEM) 00h system 01h KEYB 02h NLSFUNC 03h SHARE 04h TaskMAX 05h COMMAND 05h var TSR (or system) code and data. DR-DOS TSR's, such as KEYB, hooks interrupts using segment FFFEh instead FFFFh. --------O-214459----------------------------- INT 21 - DR MultiUser DOS 5.0 - API AX = 4459h CL = function (see #2602 at INT E0"CP/M") DS,DX = parameters Notes: DR-DOS 5.0 and Novell DOS 7 return CF set and AX=0001h this API is also available on INT E0 SeeAlso: AX=4452h,INT E0"CP/M" --------N-2144E0----------------------------- INT 21 U - Sun PC-NFS - API??? AX = 44E0h DS:DX -> ??? SS:BP -> stack frame (see #0802) Return: ??? Note: this function is also supported by Beame&Whiteside's BWPCNFS shim; the description presented here was derived from that shim Format of PC-NFS stack frame: Offset Size Description (Table 0802) 00h WORD -> previous stack frame 02h DWORD return address --------d-2144FFBXFFFF----------------------- INT 21 U - NewSpace - ??? AX = 44FFh BX = FFFFh DX = ??? Program: NewSpace is a TSR by Isogon Corporation which automatically compresses all files as they are written and decompresses them as they are read SeeAlso: AX=4414h/BX=FFFFh --------D-2145------------------------------- INT 21 - DOS 2+ - "DUP" - DUPLICATE FILE HANDLE AH = 45h BX = file handle Return: CF clear if successful AX = new handle CF set on error AX = error code (04h,06h) (see #0885 at AH=59h) Notes: moving file pointer for either handle will also move it for the other, because both will refer to the same system file table for DOS versions prior to 3.3, file writes may be forced to disk by duplicating the file handle and closing the duplicate SeeAlso: AH=3Dh,AH=46h --------D-2146------------------------------- INT 21 - DOS 2+ - "DUP2", "FORCEDUP" - FORCE DUPLICATE FILE HANDLE AH = 46h BX = file handle CX = file handle to become duplicate of first handle Return: CF clear if successful CF set on error AX = error code (04h,06h) (see #0885 at AH=59h) Notes: closes file with handle CX if it is still open DOS 3.30 hangs if BX=CX on entry moving file pointer for either handle will also move it for the other, because both will refer to the same system file table SeeAlso: AH=3Dh,AH=45h --------D-2147------------------------------- INT 21 - DOS 2+ - "CWD" - GET CURRENT DIRECTORY AH = 47h DL = drive number (00h = default, 01h = A:, etc) DS:SI -> 64-byte buffer for ASCIZ pathname Return: CF clear if successful AX = 0100h (undocumented) CF set on error AX = error code (0Fh) (see #0885 at AH=59h) Notes: the returned path does not include a drive or the initial backslash many Microsoft products for Windows rely on AX being 0100h on success under the FlashTek X-32 DOS extender, the buffer pointer is in DS:ESI SeeAlso: AH=19h,AH=3Bh,AH=71h,INT 15/AX=DE25h --------D-2148------------------------------- INT 21 - DOS 2+ - ALLOCATE MEMORY AH = 48h BX = number of paragraphs to allocate Return: CF clear if successful AX = segment of allocated block CF set on error AX = error code (07h,08h) (see #0885 at AH=59h) BX = size of largest available block Notes: DOS 2.1-6.0 coalesces free blocks while scanning for a block to allocate .COM programs are initially allocated the largest available memory block, and should free some memory with AH=49h before attempting any allocations under the FlashTek X-32 DOS extender, EBX contains a protected-mode near pointer to the allocated block on a successful return SeeAlso: AH=49h,AH=4Ah,AH=58h,AH=83h --------D-2149------------------------------- INT 21 - DOS 2+ - FREE MEMORY AH = 49h ES = segment of block to free Return: CF clear if successful CF set on error AX = error code (07h,09h) (see #0885 at AH=59h) Notes: apparently never returns an error 07h, despite official docs; DOS 2.1+ code contains only an error 09h exit DOS 2.1-6.0 does not coalesce adjacent free blocks when a block is freed, only when a block is allocated or resized the code for this function is identical in DOS 2.1-6.0 except for calls to start/end a critical section in DOS 3.0+ SeeAlso: AH=48h,AH=4Ah --------D-214A------------------------------- INT 21 - DOS 2+ - RESIZE MEMORY BLOCK AH = 4Ah BX = new size in paragraphs ES = segment of block to resize Return: CF clear if successful CF set on error AX = error code (07h,08h,09h) (see #0885 at AH=59h) BX = maximum paragraphs available for specified memory block Notes: under DOS 2.1-6.0, if there is insufficient memory to expand the block as much as requested, the block will be made as large as possible DOS 2.1-6.0 coalesces any free blocks immediately following the block to be resized SeeAlso: AH=48h,AH=49h,AH=83h --------v-214A--BX00B6----------------------- INT 21 - VIRUS??? AH = 4Ah BX = 00B6h ES = CX Return: ??? Note: this call is intercepted by the Search&Destroy SDRes v27.03 bundled with Novell DOS 7, and is presumably some virus's installation check SeeAlso: AH=0Eh/DL=ADh,AH=4Ah/BX=FFFFh,AH=D2h"VIRUS" --------v-214A--BXFFFF----------------------- INT 21 - VIRUS??? AH = 4Ah BX = FFFFh CX = 0568h SI = 0129h DI = 0000h ES = BP Return: ??? Note: this call is intercepted by the Search&Destroy SDRes v27.03 bundled with Novell DOS 7, and is presumably some virus's installation check SeeAlso: AH=0Eh/DL=ADh,AH=4Ah/BX=00B6h --------D-214B------------------------------- INT 21 - DOS 2+ - "EXEC" - LOAD AND/OR EXECUTE PROGRAM AH = 4Bh AL = type of load 00h load and execute 01h load but do not execute 03h load overlay (see #0804) 04h load and execute in background (European MS-DOS 4.0 only) "Exec & Go" (see also AH=80h) DS:DX -> ASCIZ program name (must include extension) ES:BX -> parameter block (see #0803,#0804,#0805) CX = mode (subfunction 04h only) 0000h child placed in zombie mode after termination 0001h child's return code discarded on termination Return: CF clear if successful BX,DX destroyed if subfunction 01h, process ID set to new program's PSP; get with INT 21/AH=62h CF set on error AX = error code (01h,02h,05h,08h,0Ah,0Bh) (see #0885 at AH=59h) Notes: DOS 2.x destroys all registers, including SS:SP under ROM-based DOS, if no disk path characters (colons or slashes) are included in the program name, the name is searched for in the ROM module headers (see #0808) before searching on disk for functions 00h and 01h, the calling process must ensure that there is enough unallocated memory available; if necessary, by releasing memory with AH=49h or AH=4Ah for function 01h, the AX value to be passed to the child program is put on top of the child's stack for function 03h, DOS assumes that the overlay is being loaded into memory allocated by the caller function 01h was undocumented prior to the release of DOS 5.0 some versions (such as DR-DOS 6.0) check the parameters and parameter block and return an error if an invalid value (such as an offset of FFFFh) is found background programs under European MS-DOS 4.0 must use the new executable format this function ignores the filename extension, instead checking the first two bytes of the file to determine whether there is a valid .EXE header (see #0807); if not, the file is assumed to be in .COM format. If present, the file may be in any of several formats which are extensions of the original .EXE format (see #0806) .COM-format executables begin running with the following register values: AL = 00h if first FCB has valid drive letter, FFh if not AH = 00h if second FCB has valid drive letter, FFh if not CS,DS,ES,SS = PSP segment SP = offset of last word available in first 64K segment (note: AX is always 0000h under DESQview) old-format executables begin running with the following register values: AL = 00h if first FCB has valid drive letter, FFh if not AH = 00h if second FCB has valid drive letter, FFh if not DS,ES = PSP segment SS:SP as defined in .EXE header (note: AX is always 0000h under DESQview) new executables begin running with the following register values AX = environment segment BX = offset of command tail in environment segment CX = size of automatic data segment (0000h = 64K) ES,BP = 0000h DS = automatic data segment SS:SP = initial stack the command tail corresponds to an old executable's PSP:0081h and following, except that the 0Dh is turned into a NUL (00h); new format executables have no PSP under the FlashTek X-32 DOS extender, only function 00h is supported and the pointers are passed in DS:EDX and ES:EBX DR-DOS 6 always loads .EXE-format programs with no fixups and .COM-format programs starting with 9Ch 55h (PUSHF/PUSH BP) above the 64K mark to avoid the EXEPACK bug, by extending the memory block containing the program's environment; this code is disabled if the name of the parent program as stored in the MCB is 'WIN'. BUGS: DOS 2.00 assumes that DS points at the current program's PSP Load Overlay (subfunction 03h) loads up to 512 bytes too many if the file contains additional data after the actual overlay SeeAlso: AX=4B05h,AH=4Ch,AH=4Dh,AH=64h"OS/2",AH=8Ah,INT 2E,INT 60/DI=0604h Format of EXEC parameter block for AL=00h,01h,04h: Offset Size Description (Table 0803) 00h WORD segment of environment to copy for child process (copy caller's environment if 0000h) 02h DWORD pointer to command tail to be copied into child's PSP 06h DWORD pointer to first FCB to be copied into child's PSP 0Ah DWORD pointer to second FCB to be copied into child's PSP 0Eh DWORD (AL=01h) will hold subprogram's initial SS:SP on return 12h DWORD (AL=01h) will hold entry point (CS:IP) on return SeeAlso: #0804,#0805 Format of EXEC parameter block for AL=03h: Offset Size Description (Table 0804) 00h WORD segment at which to load overlay 02h WORD relocation factor to apply to overlay if in .EXE format SeeAlso: #0803,#0805 Format of EXEC parameter block for FlashTek X-32: Offset Size Description (Table 0805) 00h PWORD 48-bit far pointer to environment string 06h PWORD 48-bit far pointer to command tail string SeeAlso: #0803,#0804 (Table 0806) Values for the executable types understood by various environments: MZ old-style DOS executable (see #0807) NE Windows or OS/2 1.x segmented ("new") executable (see #0809) LE Windows virtual device driver (VxD) linear executable (see #0822) LX variant of LE used in OS/2 2.x (see #0822) W3 Windows WIN386.EXE file; a collection of LE files PE Win32 (Windows NT and Win32s) portable executable based on Unix COFF DL HP 100LX/200LX system manager compliant executable (.EXM) MP old PharLap .EXP (see #0832) P2 PharLap 286 .EXP (see #0833) P3 PharLap 386 .EXP (see #0833) Format of .EXE file header: Offset Size Description (Table 0807) 00h 2 BYTEs .EXE signature, either "MZ" or "ZM" (5A4Dh or 4D5Ah) (see also #0806) 02h WORD number of bytes in last 512-byte page of executable 04h WORD total number of 512-byte pages in executable (includes any partial last page) 06h WORD number of relocation entries 08h WORD header size in paragraphs 0Ah WORD minimum paragraphs of memory to allocation in addition to executable's size 0Ch WORD maximum paragraphs to allocate in addition to executable's size 0Eh WORD initial SS relative to start of executable 10h WORD initial SP 12h WORD checksum (one's complement of sum of all words in executable) 14h DWORD initial CS:IP relative to start of executable 18h WORD offset within header of relocation table 40h or greater for new-format (NE,LE,LX,W3,PE,etc.) executable 1Ah WORD overlay number (normally 0000h = main program) ---new executable--- 1Ch 4 BYTEs ??? 20h WORD behavior bits 22h 26 BYTEs reserved for additional behavior info 3Ch DWORD offset of new executable (NE,LE,etc) header within disk file, or 00000000h if plain MZ executable ---Borland TLINK--- 1Ch 2 BYTEs ??? (apparently always 01h 00h) 1Eh BYTE signature FBh 1Fh BYTE TLINK version (major in high nybble, minor in low nybble) 20h 2 BYTEs ??? (v2.0 apparently always 72h 6Ah, v3.0+ seems always 6Ah 72h) ---ARJ self-extracting archive--- 1Ch 4 BYTEs signature "RJSX" (older versions, new signature is "aRJsfX" in the first 1000 bytes of the file) ---LZEXE 0.90 compressed executable--- 1Ch 4 BYTEs signature "LZ09" ---LZEXE 0.91 compressed executable--- 1Ch 4 BYTEs signature "LZ91" ---PKLITE compressed executable--- 1Ch BYTE minor version number 1Dh BYTE bits 0-3: major version bit 4: extra compression bit 5: huge (multi-segment) file 1Eh 6 BYTEs signature "PKLITE" (followed by copyright message) ---LHarc 1.x self-extracting archive--- 1Ch 4 BYTEs unused??? 20h 3 BYTEs jump to start of extraction code 23h 2 BYTEs ??? 25h 12 BYTEs signature "LHarc's SFX " ---LHA 2.x self-extracting archive--- 1Ch 8 BYTEs ??? 24h 10 BYTEs signature "LHa's SFX " (v2.10) or "LHA's SFX " (v2.13) ---TopSpeed C 3.0 CRUNCH compressed file--- 1Ch DWORD 018A0001h 20h WORD 1565h ---PKARCK 3.5 self-extracting archive--- 1Ch DWORD 00020001h 20h WORD 0700h ---BSA (Soviet archiver) self-extracting archive--- 1Ch WORD 000Fh 1Eh BYTE A7h ---LARC self-extracting archive--- 1Ch 4 BYTEs ??? 20h 11 BYTEs "SFX by LARC " ---LH self-extracting archive--- 1Ch 8 BYTEs ??? 24h 8 BYTEs "LH's SFX " ---other linkers--- 1Ch var optional information --- N N DWORDs relocation items Notes: if word at offset 02h is 4, it should be treated as 00h, since pre-1.10 versions of the MS linker set it that way if both minimum and maximum allocation (offset 0Ah/0Ch) are zero, the program is loaded as high in memory as possible (DOS only checks the maximum allocation, however) the maximum allocation is set to FFFFh by default additional data may be contained in the file beyond the end of the load image described by the .EXE header; this data may be overlays, the actual executable for newer-format executables, or debugging information (see #0813,#0837) Format of ROM Module Header: Offset Size Description (Table 0808) 00h 2 BYTEs ROM signature 55h, AAh 02h BYTE size of ROM in 512-byte blocks 03h 3 BYTEs POST initialization entry point (near JMP instruction) 06h ROM Program Name List [array] Offset Size Description 00h BYTE length of ROM program's name (00h if end of name list) 01h N BYTEs program name N+1 3 BYTEs program entry point (near JMP instruction) Format of new executable header: Offset Size Description (Table 0809) 00h 2 BYTEs "NE" (4Eh 45h) signature 02h 2 BYTEs linker version (major, then minor) 04h WORD offset from start of this header to entry table (see #0816) 06h WORD length of entry table in bytes 08h DWORD file load CRC (0 in Borland's TPW) 0Ch BYTE program flags (see #0810) 0Dh BYTE application flags (see #0811) 0Eh WORD auto data segment index 10h WORD initial local heap size 12h WORD initial stack size (added to data seg, 0000h if SS <> DS) 14h DWORD program entry point (CS:IP), "CS" is index into segment table 18h DWORD initial stack pointer (SS:SP), "SS" is segment index if SS=automatic data segment and SP=0000h, the stack pointer is set to the top of the automatic data segment, just below the local heap 1Ch WORD segment count 1Eh WORD module reference count 20h WORD length of nonresident names table in bytes 22h WORD offset from start of this header to segment table (see #0814) 24h WORD offset from start of this header to resource table 26h WORD offset from start of this header to resident names table 28h WORD offset from start of this header to module reference table 2Ah WORD offset from start of this header to imported names table (array of counted strings, terminated with a string of length 00h) 2Ch DWORD offset from start of file to nonresident names table 30h WORD count of moveable entry point listed in entry table 32h WORD file alignment size shift count 0 is equivalent to 9 (default 512-byte pages) 34h WORD number of resource table entries 36h BYTE target operating system 00h unknown 01h OS/2 02h Windows 03h European MS-DOS 4.x 04h Windows 386 05h BOSS (Borland Operating System Services) 81h PharLap 286|DOS-Extender, OS/2 82h PharLap 286|DOS-Extender, Windows 37h BYTE other EXE flags (see #0812) 38h WORD offset to return thunks or start of gangload area 3Ah WORD offset to segment reference thunks or length of gangload area 3Ch WORD minimum code swap area size 3Eh 2 BYTEs expected Windows version (minor version first) Note: this header is documented in detail in the Windows 3.1 SDK Programmer's Reference, Vol 4. Bitfields for new executable program flags: Bit(s) Description (Table 0810) 0-1 DGROUP type 0 = none 1 = single shared 2 = multiple (unshared) 3 = (null) 2 global initialization 3 protected mode only 4 8086 instructions 5 80286 instructions 6 80386 instructions 7 80x87 instructions Bitfields for new executable application flags: Bit(s) Description (Table 0811) 0-2 application type 001 full screen (not aware of Windows/P.M. API) 010 compatible with Windows/P.M. API 011 uses Windows/P.M. API 3 is a Family Application (OS/2) 5 0=executable, 1=errors in image 6 non-conforming program (valid stack is not maintained) 7 DLL or driver rather than application (SS:SP info invalid, CS:IP points at FAR init routine called with AX=module handle which returns AX=0000h on failure, AX nonzero on successful initialization) Bitfields for other new .EXE flags: Bit(s) Description (Table 0812) 0 supports long filenames 1 2.X protected mode 2 2.X proportional font 3 gangload area Format of Codeview trailer (at end of executable): Offset Size Description (Table 0813) 00h WORD signature 4E42h ('NB') 02h WORD Microsoft debug info version number 04h DWORD Codeview header offset SeeAlso: #0837 Format of new executable segment table record: Offset Size Description (Table 0814) 00h WORD offset in file (shift left by alignment shift to get byte offs) 02h WORD length of image in file (0000h = 64K) 04h WORD segment attributes (see #0815) 06h WORD number of bytes to allocate for segment (0000h = 64K) Note: the first segment table entry is entry number 1 SeeAlso: #0817 Bitfields for segment attributes: Bit(s) Description (Table 0815) 0 data segment rather than code segment 1 unused??? 2 real mode 3 iterated 4 movable 5 sharable 6 preloaded rather than demand-loaded 7 execute-only (code) or read-only (data) 8 relocations (directly following code for this segment) 9 debug info present 10,11 80286 DPL bits 12 discardable 13-15 discard priority Format of new executable entry table item (list): Offset Size Description (Table 0816) 00h BYTE number of entry points (00h if end of entry table list) 01h BYTE segment number (00h if end of entry table list) 02h 3N BYTEs entry records Offset Size Description 00h BYTE flags bit 0: exported bit 1: single data bits 2-7: unused??? 01h WORD offset within segment Format of new executable relocation data (immediately follows segment image): Offset Size Description (Table 0817) 00h WORD number of relocation items 02h 8N BYTEs relocation items Offset Size Description 00h BYTE relocation type 00h LOBYTE 02h BASE 03h PTR 05h OFFS 0Bh PTR48 0Dh OFFS32 01h BYTE flags bit 2: additive 02h WORD offset within segment 04h WORD target address segment 06h WORD target address offset SeeAlso: #0814,#0818 Format of new executable resource data: Offset Size Description (Table 0818) 00h WORD alignment shift count for resource data 02h N RECORDs resources Format of resource record: Offset Size Description 00h WORD type ID 0000h if end of resource records >= 8000h if integer type else offset from start of resource table to type string 02h WORD number of resources of this type 04h DWORD reserved for runtime use 08h N Resources (see #0819) Note: resource type and name strings are stored immediately following the resource table, and are not null-terminated SeeAlso: #0819 Format of new executable resource entry: Offset Size Description (Table 0819) 00h WORD offset in alignment units from start of file to contents of the resource data 02h WORD length of resource image in bytes 04h WORD flags bit 4: moveable bit 5: shareable bit 6: preloaded 06h WORD resource ID >= 8000h if integer resource else offset from start of resource table to resource string 08h DWORD reserved for runtime use Notes: resource type and name strings are stored immediately following the resource table, and are not null-terminated strings are counted strings, with a string of length 0 indicating the end of the resource table SeeAlso: #0818,#0820 Format of new executable module reference table [one bundle of entries]: Offset Size Description (Table 0820) 00h BYTE number of records in this bundle (00h if end of table) 01h BYTE segment indicator 00h unused FFh movable segment, segment number is in entry else segment number of fixed segment 02h N RECORDs Format of segment record Offset Size Description 00h BYTE flags bit 0: entry is exported bit 1: entry uses global (shared) data bits 7-3: number of parameter words ---fixed segment--- 01h WORD offset ---moveable segment--- 01h 2 BYTEs INT 3F instruction (CDh 3Fh) 03h BYTE segment number 05h WORD offset Note: table entries are numbered starting from 1 SeeAlso: #0821 Format of new executable resident/nonresident name table entry: Offset Size Description (Table 0821) 00h BYTE length of string (00h if end of table) 01h N BYTEs ASCII text of string N+1 WORD ordinal number (index into entry table) Notes: the first string in the resident name table is the module name; the first entry in the nonresident name table is the module description the strings are case-sensitive; if the executable was linked with /IGNORECASE, all strings are in uppercase SeeAlso: #0820 Format of Linear Executable (enhanced mode executable) header: Offset Size Description (Table 0822) 00h 2 BYTEs "LE" (4Ch 45h) signature (Windows) "LX" (4Ch 58h) signature (OS/2) 02h BYTE byte order (00h = little-endian, nonzero = big-endian) 03h BYTE word order (00h = little-endian, nonzero = big-endian) 04h DWORD executable format level 08h WORD CPU type (see also INT 15/AH=C9h) 01h Intel 80286 or upwardly compatible 02h Intel 80386 or upwardly compatible 03h Intel 80486 or upwardly compatible 04h Intel Pentium (80586) or upwardly compatible 20h Intel i860 (N10) or compatible 21h Intel "N11" or compatible 40h MIPS Mark I (R2000, R3000) or compatible 41h MIPS Mark II (R6000) or compatible 42h MIPS Mark III (R4000) or compatible 0Ah WORD target operating system 01h OS/2 02h Windows 03h European DOS 4.0 04h Windows 386 0Ch DWORD module version 10h DWORD module type (see #0823) 14h DWORD number of memory pages 18h Initial CS:EIP DWORD object number DWORD offset 20h Initial SS:ESP DWORD object number DWORD offset 28h DWORD memory page size 2Ch DWORD (Windows LE) bytes on last page (OS/2 LX) page offset shift count 30h DWORD fixup section size 34h DWORD fixup section checksum 38h DWORD loader section size 3Ch DWORD loader section checksum 40h DWORD offset of object table (see #0824) 44h DWORD object table entries 48h DWORD object page map table offset (see #0826) 4Ch DWORD object iterate data map offset 50h DWORD resource table offset 54h DWORD resource table entries 58h DWORD resident names table offset (see #0827) 5Ch DWORD entry table offset (see #0828,#0829) 60h DWORD module directives table offset 64h DWORD Module Directives entries 68h DWORD Fixup page table offset 6Ch DWORD Fixup record table offset (see #0831) 70h DWORD imported modules name table offset 74h DWORD imported modules count 78h DWORD imported procedures name table offset 7Ch DWORD per-page checksum table offset 80h DWORD data pages offset 84h DWORD preload page count 88h DWORD non-resident names table offset 8Ch DWORD non-resident names table length 90h DWORD non-resident names checksum 94h DWORD automatic data object 98h DWORD debug information offset 9Ch DWORD debug information length A0h DWORD preload instance pages number A4h DWORD demand instance pages number A8h DWORD extra heap allocation ACh 12 BYTEs reserved B8h DWORD offset of VERSIONINFO resource (MS-Windows VxD only) BCh DWORD pointer to ??? (dynamically-loadable VxDs only???) C0h WORD device ID (MS-Windows VxD only) C2h WORD DDK version (MS-Windows VxD only) Note: used by EMM386.EXE, QEMM, and Windows 3.0 Enhanced Mode drivers Bitfields for Linear Executable module type: Bit(s) Description (Table 0823) 2 initialization (only for DLLs) 0 = global, 1 = per-process 4 no internal fixups in executable image 5 no external fixups in executable image 8-10 API compatibility 0 = unknown 1 = incompatible with PM windowing \ 2 = compatible with PM windowing > (only for 3 = uses PM windowing API / programs) 13 module not loadable (only for programs) 15-17 module type 000 program 001 library (DLL) 011 protected memory library module 100 physical device driver 110 virtual device driver 30 per-process library termination (requires valid CS:EIP, can't be set for .EXE) Format of object table entry: Offset Size Description (Table 0824) 00h DWORD virtual size in bytes 04h DWORD relocation base address 08h DWORD object flags (see #0825) 0Ch DWORD page map index 10h DWORD page map entries (see #0826) 14h 4 BYTEs reserved??? (apparently always zeros) Bitfields for object flags: Bit(s) Description (Table 0825) 0 readable 1 writable 2 executable 3 resource 4 discardable 5 shared 6 preloaded 7 invalid 8-9 type 00 normal 01 zero-filled 10 resident 11 resident and contiguous 10 resident and long-lockable 11 reserved 12 16:16 alias required 13 "BIG" (Huge: 32-bit) 14 conforming 15 "OBJECT_I/O_PRIVILEGE_LEVEL" 16-31 reserved Format of object page map table entry: Offset Size Description (Table 0826) 00h BYTE ??? (usually 00h) 01h WORD (big-endian) index to fixup table 0000h if no relocation info 03h BYTE type (00h hard copy in file, 03h some relocation needed) Format of resident names table entry: Offset Size Description (Table 0827) 00h BYTE length of name 01h N BYTEs name N+1 3 BYTEs ??? Format of LE linear executable entry table: Offset Size Description (Table 0828) 00h BYTE number of entries in table 01h 10 BYTEs per entry Offset Size Description 00h BYTE bit flags bit 0: non-empty bundle bit 1: 32-bit entry 01h WORD object number 03h BYTE entry type flags bit 0: exported bit 1: uses single data rather than instance bit 2: reserved bits 3-7: number of stack parameters 04h DWORD offset of entry point 08h 2 BYTEs ??? Note: empty bundles (bit flags at 00h = 00h) are used to skip unused indices, and do not contain the remaining nine bytes Format of LX linear executable entry table [array]: Offset Size Description (Table 0829) 00h BYTE number of bundles following (00h = end of entry table) 01h BYTE bundle type 00h empty 01h 16-bit entry 02h 286 callgate entry 03h 32-bit entry 04h forwarder entry bit 7 set if additional parameter typing information is present ---bundle type 00h--- no additional fields ---bundle type 01h--- 02h WORD object number 04h BYTE entry flags bit 0: exported bits 7-3: number of stack parameters 05h WORD offset of entry point in object (shifted by page size shift) ---bundle type 02h--- 02h WORD object number 04h BYTE entry flags bit 0: exported bits 7-3: number of stack parameters 05h WORD offset of entry point in object 07h WORD reserved for callgate selector (used by loader) ---bundle type 03h--- 02h WORD object number 04h BYTE entry flags bit 0: exported bits 7-3: number of stack parameters 05h DWORD offset of entry point in object ---bundle type 04h--- 02h WORD reserved 04h BYTE forwarder flags bit 0: import by ordinal bits 7-1 reserved 05h WORD module ordinal (forwarder's index into Import Module Name table) 07h DWORD procedure name offset or import ordinal number Note: all fields after the first two bytes are repeated N times Bitfields for linear executable fixup type: Bit(s) Description (Table 0830) 7 ordinal is BYTE rather than WORD 6 16-rather than 8-object number/module ordinal 5 addition with DWORD rather than WORD 4 relocation info has size with new two bytes at end 3 reserved (0) 2 set if add to destination, clear to replace destination 1-0 type 00 internal fixup 01 external fixup, imported by ordinal 10 external fixup, imported by name 11 internal fixup via entry table Format of linear executable fixup record: Offset Size Description (Table 0831) 00h BYTE type bits 7-4: modifier (0001 single, 0011 multiple) bits 3-0: type 0000 byte offset 0010 word segment 0011 16-bit far pointer (DWORD) 0101 16-bit offset 0110 32-bit far pointer (PWORD) 0111 32-bit offset 1000 near call or jump, WORD/DWORD based on seg attrib 01h BYTE linear executable fixup type (see #0830) ---if single type--- 02h WORD offset within page 04h relocation information ---internal fixup--- BYTE object number ---external,ordinal--- BYTE one-based module number in Import Module table BYTE/WORD ordinal number WORD/DWORD value to add (only present if modifier bit 4 set) ---external,name--- BYTE one-based module number in Import Module table WORD offset in Import Procedure names WORD/DWORD value to add (only present if modifier bit 4 set) ---if multiple type--- 02h BYTE number of items 03h var relocation info as for "single" type (see above) N WORDs offsets of items to relocate Format of old Phar Lap .EXP file header: Offset Size Description (Table 0832) 00h 2 BYTEs "MP" (4Dh 50h) signature 02h WORD remainder of image size / page size (page size = 512h) 04h WORD size of image in pages 06h WORD number of relocation items 08h WORD header size in paragraphs 0Ah WORD minimum number of extra 4K pages to be allocated at the end of program, when it is loaded 0Ch WORD maximum number of extra 4K pages to be allocated at the end of program, when it is loaded 0Eh DWORD initial ESP 12h WORD word checksum of file 14h DWORD initial EIP 18h WORD offset of first relocation item 1Ah WORD overlay number 1Ch WORD ??? (wants to be 1) SeeAlso: #0833 Format of new Phar Lap .EXP file header: Offset Size Description (Table 0833) 00h 2 BYTEs signature ("P2" for 286 .EXP executable, "P3" for 386 .EXP) 02h WORD level (01h flat-model file, 02h multisegmented file) 04h WORD header size 06h DWORD file size in bytes 0Ah WORD checksum 0Ch DWORD offset of run-time parameters within file (see #0835) 10h DWORD size of run-time parameters in bytes 14h DWORD offset of relocation table within file 18h DWORD size of relocation table in bytes 1Ch DWORD offset of segment information table within file (see #0834) 20h DWORD size of segment information table in bytes 24h WORD size of segment information table entry in bytes 26h DWORD offset of load image within file 2Ah DWORD size of load image on disk 2Eh DWORD offset of symbol table within file 32h DWORD size of symbol table in bytes 36h DWORD offset of GDT within load image 3Ah DWORD size of GDT in bytes 3Eh DWORD offset of LDT within load image 42h DWORD size of LDT in bytes 46h DWORD offset of IDT within load image 4Ah DWORD size of IDT in bytes 4Eh DWORD offset of TSS within load image 52h DWORD size of TSS in bytes 56h DWORD minimum number of extra bytes to be allocated at end of program (level 1 executables only) 5Ah DWORD maximum number of extra bytes to be allocated at end of program (level 1 executables only) 5Eh DWORD base load offset (level 1 executables only) 62h DWORD initial ESP 66h WORD initial SS 68h DWORD initial EIP 6Ch WORD initial CS 6Eh WORD initial LDT 70h WORD initial TSS 72h WORD flags bit 0: load image is packed bit 1: 32-bit checksum is present bits 4-2: type of relocation table 74h DWORD memory requirements for load image 78h DWORD 32-bit checksum (optional) 7Ch DWORD size of stack segment in bytes 80h 256 BYTEs reserved (0) SeeAlso: #0832,#0836 Format of Phar Lap segment information table entry: Offset Size Description (Table 0834) 00h WORD selector number 02h WORD flags 04h DWORD base offset of selector 08h DWORD minimum number of extra bytes to be allocated to the segment Format of 386|DOS-Extender run-time parameters: Offset Size Description (Table 0835) 00h 2 BYTEs signature "DX" (44h 58h) 02h WORD minimum number of real-mode params to leave free at run time 04h WORD maximum number of real-mode params to leave free at run time 06h WORD minimum interrupt buffer size in KB 08h WORD maximum interrupt buffer size in KB 0Ah WORD number of interrupt stacks 0Ch WORD size in KB of each interrupt stack 0Eh DWORD offset of byte past end of real-mode code and data 12h WORD size in KB of call buffers 14h WORD flags bit 0: file is virtual memory manager bit 1: file is a debugger 16h WORD unprivileged flag (if nonzero, executes at ring 1, 2, or 3) 18h 104 BYTEs reserved (0) Format of Phar Lap repeat block header: Offset Size Description (Table 0836) 00h WORD byte count 02h BYTE repeat string length Format of Borland debugging information header (following load image): Offset Size Description (Table 0837) 00h WORD signature 52FBh 02h WORD version ID 04h DWORD size of name pool in bytes 08h WORD number of names in name pool 0Ah WORD number of type entries 0Ch WORD number of structure members 0Eh WORD number of symbols 10h WORD number of global symbols 12h WORD number of modules 14h WORD number of locals (optional) 16h WORD number of scopes in table 18h WORD number of line-number entries 1Ah WORD number of include files 1Ch WORD number of segment records 1Eh WORD number of segment/file correlations 20h DWORD size of load image after removing uninitialized data and debug information 24h DWORD debugger hook; pointer into debugged program whose meaning depends on program flags 28h BYTE program flags bit 0: case-sensitive link bit 1: pascal overlay program 29h WORD no longer used 2Bh WORD size of data pool in bytes 2Dh BYTE padding 2Eh WORD size of following header extension (currently 00h, 10h, or 20h) 30h WORD number of classes 32h WORD number of parents 34h WORD number of global classes (currently unused) 36h WORD number of overloads (currently unused) 38h WORD number of scope classes 3Ah WORD number of module classes 3Ch WORD number of coverage offsets 3Eh DWORD offset relative to symbol base of name pool 42h WORD number of browser information records 44h WORD number of optimized symbol records 46h WORD debugging flags 48h 8 BYTEs padding Note: additional information on the Borland debugging info may be found in Borland's Open Architecture Handbook SeeAlso: #0813 --------U-214B------------------------------- INT 21 - ELRES v1.0 only - INSTALLATION CHECK AH = 4Bh DS:DX = 0000h:0000h Return: ES:BX -> ELRES history structure (see #0606 at AH=2Bh/CX=454Ch) DX = DABEh (signature, DAve BEnnett) Program: ELRES is an MS-DOS return code (errorlevel) recorder by David H. Bennett SeeAlso: AH=2Bh/CX=454Ch --------v-214B04----------------------------- INT 21 - VIRUS - "MG", "699"/"Thirteen Minutes" - INSTALLATION CHECK AX = 4B04h Return: CF clear if "MG" resident AX = 044Bh if "699"/"Thirteen Minutes" resident SeeAlso: AX=4243h,AH=4Ah/BX=FFFFh,AX=4B21h --------D-214B05----------------------------- INT 21 - DOS 5+ - SET EXECUTION STATE AX = 4B05h DS:DX -> execution state structure (see #0838) Return: CF clear if successful AX = 0000h CF set on error AX = error code (see #0885 at AH=59h) Note: used by programs which intercept AX=4B00h to prepare new programs for execution (including setting the DOS version number). No DOS, BIOS or other software interrupt may be called after return from this call before commencement of the child process. If DOS is running in the HMA, A20 is turned off on return from this call. SeeAlso: AH=4Bh Format of execution state structure: Offset Size Description (Table 0838) 00h WORD reserved (00h) 02h WORD type flags bit 0: program is an .EXE bit 1: program is an overlay 04h DWORD pointer to ASCIZ name of program file 08h WORD PSP segment of new program 0Ah DWORD starting CS:IP of new program 0Eh DWORD program size including PSP --------v-214B20----------------------------- INT 21 - VIRUS - "Holocaust"/"Telefonica" - ??? AX = 4B20h SeeAlso: AX=4B04h,AX=4B21h --------v-214B21----------------------------- INT 21 C - VIRUS - "Holocaust"/"Telefonica" - ??? AX = 4B21h Note: called at completion of virus installation SeeAlso: AX=4B04h,AX=4B20h,AX=4B25h --------v-214B25----------------------------- INT 21 - VIRUS - "1063"/"Mono" - INSTALLATION CHECK AX = 4B25h Return: DI = 1234h if resident SeeAlso: AX=4B21h,AX=4B40h --------v-214B40----------------------------- INT 21 - VIRUS - "Plastique"/"AntiCad" - INSTALLATION CHECK AX = 4B40h Return: AX = 5678h if resident SeeAlso: AX=4B25h,AX=4B41h,AX=4B4Ah --------v-214B41----------------------------- INT 21 - VIRUS - "Plastique"/"AntiCad" - ??? AX = 4B41h ??? Return: ??? SeeAlso: AX=4B40h --------v-214B4A----------------------------- INT 21 - VIRUS - "Jabberwocky" - INSTALLATION CHECK AX = 4B4Ah Return: AL = 57h if resident SeeAlso: AX=4B40h,AX=4B4Bh --------v-214B4B----------------------------- INT 21 - VIRUS - "Horse-2" - INSTALLATION CHECK AX = 4B4Bh Return: CF clear if resident SeeAlso: AX=4B4Ah,AX=4B4Dh --------v-214B4D----------------------------- INT 21 - VIRUS - "Murphy-2", "Patricia"/"Smack" - INSTALLATION CHECK AX = 4B4Dh Return: CF clear if resident SeeAlso: AX=4B4Ah,AX=4B50h --------v-214B50----------------------------- INT 21 - VIRUS - "Plastique-2576"/"AntiCad-2576" - INSTALLATION CHECK AX = 4B50h Return: AX = 1234h if resident SeeAlso: AX=4B4Dh,AX=4B53h,AX=4B60h --------v-214B53----------------------------- INT 21 - VIRUS - "Horse" - INSTALLATION CHECK AX = 4B53h Return: CF clear if resident SeeAlso: AX=4B50h,AX=4B53h/BX=2121h,AX=4B55h --------v-214B53BX2121----------------------- INT 21 - VIRUS - "One Half" - INSTALLATION CHECK AX = 4B53h BX = 2121h CX = 1212h DX = 0236h Return: AX = 454Bh if installed SeeAlso: AX=4B50h,AX=4B53h,AX=4B55h --------v-214B55----------------------------- INT 21 - VIRUS - "Sparse" - INSTALLATION CHECK AX = 4B55h Return: AX = 1231h if resident SeeAlso: AX=4B53h,AX=4B59h --------v-214B59----------------------------- INT 21 - VIRUS - "Murphy-1", "Murphy-4" - INSTALLATION CHECK AX = 4B59h Return: CF clear if resident SeeAlso: AX=4B50h,AX=4B5Eh --------v-214B5E----------------------------- INT 21 - VIRUS - "Brothers" - INSTALLATION CHECK AX = 4B5Eh Return: CF clear if resident SeeAlso: AX=4B59h,AX=4B87h --------v-214B60----------------------------- INT 21 - VIRUS - "Plastique-2576"/"AntiCad-2576" - ??? AX = 4B60h ??? Return: ??? SeeAlso: AX=4B50h --------v-214B87----------------------------- INT 21 - VIRUS - "Shirley" - INSTALLATION CHECK AX = 4B87h Return: AX = 6663h if resident SeeAlso: AX=4B5Eh,AX=4B95h --------v-214B95----------------------------- INT 21 - VIRUS - "Zherkov-1882" - INSTALLATION CHECK AX = 4B95h Return: AX = 1973h if resident SeeAlso: AX=4B87h,AX=4BA7h --------v-214BA7----------------------------- INT 21 - VIRUS - "1876"/"Dash-em" - INSTALLATION CHECK AX = 4BA7h Return: AX = B459h if resident SeeAlso: AX=4B95h,AX=4BAAh --------v-214BAA----------------------------- INT 21 - VIRUS - "Nomenklatura" - INSTALLATION CHECK AX = 4BAAh Return: CF clear if resident SeeAlso: AX=4BA7h,AX=4BAFh --------v-214BAF----------------------------- INT 21 - VIRUS - "948"/"Screenplus1", "Magnitogorsk" - INSTALLATION CHECK AX = 4BAFh Return: AL = AFh if "Magnitogorsk" resident AL = FAh if "948"/"Screenplus1" resident SeeAlso: AX=4BAAh,AX=4BDDh --------v-214BDD----------------------------- INT 21 - VIRUS - "Lozinsky"/"Zherkov" - INSTALLATION CHECK AX = 4BDDh Return: AX = 1234h SeeAlso: AX=4BAFh,AX=4BFEh --------v-214BEE----------------------------- INT 21 - F-DRIVER.SYS v1.14+ - GRAB INT 21 AX = 4BEEh Return: AX = status 1234h grab was successful 2345h failed (INT 21 grabbed previously) Program: F-DRIVER.SYS is part of the shareware F-PROT virus/trojan protection package by Fridrik Skulason Note: when called the first time, this function moves the INT 21 monitoring code from its original location in the INT 21 chain to be the first thing called by INT 21. This is the mechanism used by F-NET. SeeAlso: INT 2F/AX=4653h --------k-214BF0----------------------------- INT 21 - DIET v1.10+ (Overlay Mode) - INSTALLATION CHECK AX = 4BF0h Return: CF clear if installed AX = 899Dh Program: DIET is an executable-compression program by Teddy Matsumoto SeeAlso: AX=37D0h,AX=4BF1h --------k-214BF1----------------------------- INT 21 - DIET v1.10+ (Overlay Mode) - EXPAND PROGRAM??? AX = 4BF1h Return: ??? SeeAlso: AX=37D0h,AX=4BF0h --------v-214BFE----------------------------- INT 21 - VIRUS - "Hitchcock", "Dark Avenger-1028", "1193" - INSTALLATION CHECK AX = 4BFEh Return: AX = 1234h if "Hitchcock" resident AX = ABCDh if "1193"/"Copyright" resident DI = 55BBh if "Dark Avenger-1028" resident SeeAlso: AX=4BDDh,AX=4BFFh"Justice" --------v-214BFF----------------------------- INT 21 - VIRUS - "USSR-707", "Justice", "Europe 92" - INSTALLATION CHECK AX = 4BFFh Return: BL = FFh if "USSR-707" resident DI = 55AAh if "Justice" resident CF clear if "Europe 92" resident SeeAlso: AX=4BFEh,AX=4BFFh"Cascade",AX=5252h --------v-214BFFSI0000----------------------- INT 21 - VIRUS - "Cascade" - INSTALLATION CHECK AX = 4BFFh SI = 0000h DI = 0000h Return: DI = 55AAh if installed SeeAlso: AX=4BFFh"Justice",AX=5252h --------D-214C------------------------------- INT 21 - DOS 2+ - "EXIT" - TERMINATE WITH RETURN CODE AH = 4Ch AL = return code Return: never returns Notes: unless the process is its own parent (see #0603 at AH=26h, offset 16h in PSP), all open files are closed and all memory belonging to the process is freed all network file locks should be removed before calling this function SeeAlso: AH=00h,AH=26h,AH=4Bh,AH=4Dh,INT 15/AH=12h/BH=02h,INT 20,INT 22 SeeAlso: INT 60/DI=0601h ----------214C57----------------------------- INT 21 - Headroom - ??? AX = 4C57h DS:DX -> target address Note: jumps to target address instead of terminating program SeeAlso: AX=5758h --------D-214D------------------------------- INT 21 - DOS 2+ - GET RETURN CODE (ERRORLEVEL) AH = 4Dh Return: AH = termination type 00h normal (INT 20,INT 21/AH=00h, or INT 21/AH=4Ch) 01h control-C abort 02h critical error abort 03h terminate and stay resident (INT 21/AH=31h or INT 27) AL = return code Notes: the word in which DOS stores the return code is cleared after being read by this function, so the return code can only be retrieved once COMMAND.COM stores the return code of the last external command it executed as ERRORLEVEL this call should not be used if the child was started with AX=4B04h; use AH=8Ah instead the following sequence will close a Virtual DOS Machine under OS/2 2.0: MOV AH,4Dh INT 21h HLT DB 02h,0FDh This sequence is the only way to close a specific VDM which was booted from floppy or a disk image. SeeAlso: AH=4Bh,AH=4Ch,AH=8Ah --------D-214E------------------------------- INT 21 - DOS 2+ - "FINDFIRST" - FIND FIRST MATCHING FILE AH = 4Eh AL = special flag for use by APPEND (see note below) CX = file attribute mask (see #0643 at AX=4301h) (bits 0 and 5 ignored) 0088h (Novell DOS 7) find first deleted file DS:DX -> ASCIZ file specification (may include path and wildcards) Return: CF clear if successful [DTA] = FindFirst data block (see #0839) CF set on error AX = error code (02h,03h,12h) (see #0885 at AH=59h) Notes: for search attributes other than 08h, all files with at MOST the specified combination of hidden, system, and directory attributes will be returned. Under DOS 2.x, searching for attribute 08h (volume label) will also return normal files, while under DOS 3.0+ only the volume label (if any) will be returned. this call also returns successfully if given the name of a character device without wildcards. DOS 2.x returns attribute 00h, size 0, and the current date and time. DOS 3.0+ returns attribute 40h and the current date and time. immediately after an INT 2F/AX=B711h (APPEND return found name), the name at DS:DX will be overwritten; if AL=00h on entry, the actual found pathname will be stored, otherwise, the actual found path will be prepended to the original filespec without a path. under LANtastic, this call may be used to obtain a list of a server's shared resources by searching for "\\SERVER\*.*"; a list of printer resources may be obtained by searching for "\\SERVER\@*.*" under the FlashTek X-32 DOS extender, the filespec pointer is in DS:EDX BUGS: under DOS 3.x and 4.x, the second and subsequent calls to this function with a character device name (no wildcards) and search attributes which include the volume-label bit (08h) will fail unless there is an intervening DOS call which implicitly or explicity performs a directory search without the volume-label bit. Such implicit searches are performed by CREATE (AH=3Ch), OPEN (AH=3Dh), UNLINK (AH=41h), and RENAME (AH=56h) DR-DOS 3.41 and 5.0 return the Directory attribute for the volume label SeeAlso: AH=11h,AH=4Fh,AX=4301h,AX=714Eh,AX=71A1h,INT 2F/AX=111Bh SeeAlso: INT 2F/AX=B711h Format of FindFirst data block: Offset Size Description (Table 0839) ---PC-DOS 3.10, PC-DOS 4.01, MS-DOS 3.2/3.3/5.0--- 00h BYTE drive letter (bits 0-6), remote if bit 7 set 01h 11 BYTEs search template 0Ch BYTE search attributes ---DOS 2.x (and some DOS 3.x???)--- 00h BYTE search attributes 01h BYTE drive letter 02h 11 BYTEs search template ---WILDUNIX.COM--- 00h 12 BYTEs 15-character wildcard search pattern and drive letter (packed) 0Ch BYTE search attributes ---DOS 2.x and most 3.x--- 0Dh WORD entry count within directory 0Fh DWORD pointer to DTA??? 13h WORD cluster number of start of parent directory ---PC-DOS 4.01, MS-DOS 3.2/3.3/5.0--- 0Dh WORD entry count within directory 0Fh WORD cluster number of start of parent directory 11h 4 BYTEs reserved ---all versions, documented fields--- 15h BYTE attribute of file found 16h WORD file time (see #0876 at AX=5700h) 18h WORD file date (see #0877 at AX=5700h) 1Ah DWORD file size 1Eh 13 BYTEs ASCIZ filename+extension --------f-214E------------------------------- INT 21 - WILDUNIX.COM internal - INSTALLATION CHECK AH = 4Eh DS:DX = 0000h:0000h Return: AH = 99h if installed Program: WILDUNIX.COM is a resident Unix-style wildcard expander by Steve Hosgood and Terry Barnaby --------D-214F------------------------------- INT 21 - DOS 2+ - "FINDNEXT" - FIND NEXT MATCHING FILE AH = 4Fh [DTA] = data block from previous FindFirst or FindNext call Return: CF clear if successful CF set on error AX = error code (12h) (see #0885 at AH=59h) Note: under Novell DOS 7, if the FindFirst call (AH=4Eh) had CX=0088h, then the next matching deleted file will be returned BUG: DR-DOS 3.41 and 5.0 return the Directory attribute for the volume label SeeAlso: AH=12h,AH=4Eh,AX=714Fh,AX=71A1h --------D-2150------------------------------- INT 21 - DOS 2+ internal - SET CURRENT PROCESS ID (SET PSP ADDRESS) AH = 50h BX = segment of PSP for new process Notes: DOS uses the current PSP address to determine which processes own files and memory; it corresponds to process identifiers used by other OSs under DOS 2.x, this function cannot be invoked inside an INT 28h handler without setting the Critical Error flag under MS-DOS 3.0+ and DR-DOS 3.41+, this function does not use any of the DOS-internal stacks and may thus be called at any time, even during another INT 21h call some Microsoft applications such as Quick C 2.51 use segments of 0000h and FFFFh and direct access to the SDA (see #0892 at AX=5D06h) to test whether they are running under MS-DOS rather than a compatible OS; although one should only call this function with valid PSP addresses, any program hooking it should be prepared to handle invalid addresses this function is supported by the OS/2 compatibility box this call was undocumented prior to the release of DOS 5.0 SeeAlso: AH=26h,AH=51h,AH=62h --------D-2151------------------------------- INT 21 - DOS 2+ internal - GET CURRENT PROCESS ID (GET PSP ADDRESS) AH = 51h Return: BX = segment of PSP for current process Notes: DOS uses the current PSP address to determine which processes own files and memory; it corresponds to process identifiers used by other OSs under DOS 2.x, this function cannot be invoked inside an INT 28h handler without setting the Critical Error flag under DOS 3.0+, this function does not use any of the DOS-internal stacks and may thus be called at any time, even during another INT 21h call supported by OS/2 compatibility box identical to the documented AH=62h this call was undocumented prior to the release of DOS 5.0 SeeAlso: AH=26h,AH=50h,AH=62h --------D-2152------------------------------- INT 21 U - DOS 2+ internal - "SYSVARS" - GET LIST OF LISTS AH = 52h Return: ES:BX -> DOS list of lists (see #0840) Notes: partially supported by OS/2 v1.1 compatibility box (however, most pointers are FFFFh:FFFFh, LASTDRIVE is FFh, and the NUL header "next" pointer is FFFFh:FFFFh). partially supported by the Windows NT DOS box; contains only a rudimentary Current Directory Structure (see #0857) on return, ES points at the DOS data segment (see also INT 2F/AX=1203h) Quarterdeck's suggested check for the use of its DOSDATA.SYS or DOS-UP.SYS is to test whether the list-of-lists segment is greater than the segment of the first memory block; a better check for DOS-UP.SYS is INT 21/AX=2B01h/CX=444Dh SeeAlso: INT 2F/AX=1203h Format of List of Lists: Offset Size Description (Table 0840) -24 WORD (DOS 3.1+) contents of CX from INT 21/AX=5E01h -22 WORD (DOS ???+) LRU counter for FCB caching -20 WORD (DOS ???+) LRU counter for FCB opens -18 DWORD (DOS ???+) address of OEM function handler (see INT 21/AH=F8h) FFFFh:FFFFh if not installed or not available -14 WORD (DOS ???+) offset in DOS CS of code to return from INT 21 call -12 WORD (DOS 3.1+) sharing retry count (see AX=440Bh) -10 WORD (DOS 3.1+) sharing retry delay (see AX=440Bh) -8 DWORD (DOS 3.0+) pointer to current disk buffer -4 WORD (DOS 3.0+) pointer in DOS data segment of unread CON input when CON is read via a handle, DOS reads an entire line, and returns the requested portion, buffering the rest for the next read. 0000h indicates no unread input -2 WORD segment of first memory control block (see #0841) 00h DWORD pointer to first Drive Parameter Block (see #0620 at AH=32h) 04h DWORD -> first System File Table (see #0851,#0852,#0853,#0854) 08h DWORD pointer to active CLOCK$ device's header (most recently loaded driver with CLOCK bit set) 0Ch DWORD pointer to active CON device's header (most recently loaded driver with STDIN bit set) ---DOS 2.x--- 10h BYTE number of logical drives in system 11h WORD maximum bytes/block of any block device 13h DWORD pointer to first disk buffer (see #0861,#0862) 17h 18 BYTEs actual NUL device driver header (not a pointer!) NUL is always the first device on DOS's linked list of device drivers. (see #0858) ---DOS 3.0--- 10h BYTE number of block devices 11h WORD maximum bytes/block of any block device 13h DWORD pointer to first disk buffer (see #0862,#0864) 17h DWORD pointer to array of current directory structures (see #0855) 1Bh BYTE value of LASTDRIVE command in CONFIG.SYS (default 5) 1Ch DWORD pointer to STRING= workspace area 20h WORD size of STRING area (the x in STRING=x from CONFIG.SYS) 22h DWORD pointer to FCB table 26h WORD the y in FCBS=x,y from CONFIG.SYS 28h 18 BYTEs actual NUL device driver header (not a pointer!) NUL is always the first device on DOS's linked list of device drivers. (see #0858) ---DOS 3.1-3.3--- 10h WORD maximum bytes per sector of any block device 12h DWORD pointer to first disk buffer in buffer chain (see #0862) 16h DWORD pointer to array of current directory structures (see #0855) 1Ah DWORD pointer to system FCB tables (see #0852,#0853,#0854) 1Eh WORD number of protected FCBs (the y in the CONFIG.SYS FCBS=x,y) 20h BYTE number of block devices installed 21h BYTE number of available drive letters (largest of 5, installed block devices, and CONFIG.SYS LASTDRIVE=). Also size of current directory structure array. 22h 18 BYTEs actual NUL device driver header (not a pointer!) NUL is always the first device on DOS's linked list of device drivers. (see #0858) 34h BYTE number of JOIN'ed drives ---DOS 4.x--- 10h WORD maximum bytes per sector of any block device 12h DWORD pointer to disk buffer info record (see #0864,#0865) Note: although the initialization code in IO.SYS uses this pointer, MSDOS.SYS does not, instead using the hardcoded address of the info record 16h DWORD pointer to array of current directory structures (see #0855,#0856) 1Ah DWORD pointer to system FCB tables (see #0852,#0853,#0854) 1Eh WORD number of protected FCBs (the y in the CONFIG.SYS FCBS=x,y) (always 00h for DOS 5.0) 20h BYTE number of block devices installed 21h BYTE number of available drive letters (largest of 5, installed block devices, and CONFIG.SYS LASTDRIVE=). Also size of current directory structure array. 22h 18 BYTEs actual NUL device driver header (not a pointer!) NUL is always the first device on DOS's linked list of device drivers. (see #0858) 34h BYTE number of JOIN'ed drives 35h WORD pointer within IBMDOS code segment to list of special program names (see #0874) (always 0000h for DOS 5.0) 37h DWORD pointer to FAR routine for resident IFS utility functions (see #0870) may be called by any IFS driver which does not wish to service functions 20h or 24h-28h itself 3Bh DWORD pointer to chain of IFS (installable file system) drivers 3Fh WORD the x in BUFFERS x,y (rounded up to multiple of 30 if in EMS) 41h WORD number of lookahead buffers (the y in BUFFERS x,y) 43h BYTE boot drive (1=A:) 44h BYTE flag: 01h to use DWORD moves (80386+), 00h otherwise 45h WORD extended memory size in KB ---DOS 5.0-6.0--- 10h 39 BYTEs as for DOS 4.x (see above) 37h DWORD pointer to SETVER program list or 0000h:0000h 3Bh WORD (DOS=HIGH) offset in DOS CS of function to fix A20 control when executing special .COM format 3Dh WORD PSP of most-recently EXECed program if DOS in HMA, 0000h if low used for maintaining count of INT 21 calls which disable A20 on return 3Fh 8 BYTEs as for DOS 4.x (see above) ---Windows NT DOS Box--- 10h 6 BYTEs ??? 16h DWORD pointer to array of current directory structures (see #0857) 1Ah 6 BYTEs ??? 20h BYTE number of block devices installed 21h BYTE number of local drive letters (= installed block devices) Also size of current directory structure array. 22h 18 BYTEs actual NUL device driver header (not a pointer!) NUL is always the first device on DOS's linked list of device drivers. (see #0858) Format of DOS memory control block (see also below): Offset Size Description (Table 0841) 00h BYTE block type: 5Ah if last block in chain, otherwise 4Dh 01h WORD PSP segment of owner or special flag value (see #0842) 03h WORD size of memory block in paragraphs 05h 3 BYTEs unused by MS-DOS (386MAX) if locked-out block, region start/prev region end ---DOS 2.x,3.x--- 08h 8 BYTEs unused ---DOS 4.0+ --- 08h 8 BYTEs ASCII program name if PSP memory block or DR-DOS UMB, else garbage null-terminated if less than 8 characters Notes: the next MCB is at segment (current + size + 1) under DOS 3.1+, the first memory block is the DOS data segment, containing installable drivers, buffers, etc. Under DOS 4.0+ it is divided into subsegments, each with its own memory control block (see #0845), the first of which is at offset 0000h. for DOS 5+, blocks owned by DOS may have either "SC" or "SD" in bytes 08h and 09h. "SC" is system code or locked-out inter-UMB memory, "SD" is system data, device drivers, etc. Some versions of DR-DOS use only seven characters of the program name, placing a NUL in the eighth byte. SeeAlso: #0843,#0844,#0845 (Table 0842) Values for special flag PSP segments: 0000h free 0006h DR-DOS XMS UMB 0007h DR-DOS excluded upper memory ("hole") 0008h belongs to DOS FFF7h 386MAX v6.01+ ??? FFFAh 386MAX UMB control block (see #0697 at AX=4402h"386MAX") FFFDh 386MAX locked-out memory FFFEh 386MAX UMB (normally immediately follows its control block) FFFFh 386MAX v6.01+ device driver Format of MS-DOS 5+ UMB control block: Offset Size Description (Table 0843) 00h BYTE type: 5Ah if last block in chain, 4Dh otherwise 01h WORD first available paragraph in UMB if control block at start of UMB, 000Ah if control block at end of UMB 03h WORD length in paragraphs of following UMB or locked-out region 05h 3 BYTEs unused 08h 8 BYTEs block type name: "UMB" if start block, "SM" if end block in UMB Format of STARLITE (General Software's Embedded DOS) memory control block: Offset Size Description (Table 0844) 00h BYTE block type: 5Ah if last block in chain, otherwise 4Dh 01h WORD PSP segment of owner, 0000h if free, 0008h if belongs to DOS 03h WORD size of memory block in paragraphs 05h BYTE unused 06h WORD segment address of next memory control block (0000h if last) 08h WORD segment address of previous memory control block or 0000h 0Ah 6 BYTEs reserved Format of DOS 4.0+ data segment subsegment control blocks: Offset Size Description (Table 0845) 00h BYTE subsegment type (blocks typically appear in this order) "D" device driver "E" device driver appendage "I" IFS (Installable File System) driver "F" FILES= control block storage area (for FILES>5) "X" FCBS= control block storage area, if present "C" BUFFERS EMS workspace area (if BUFFERS /X option used) "B" BUFFERS= storage area "L" LASTDRIVE= current directory structure array storage area "S" STACKS= code and data area, if present (see #0846,#0847) "T" INSTALL= transient code 01h WORD paragraph of subsegment start (usually the next paragraph) 03h WORD size of subsegment in paragraphs 05h 3 BYTEs unused 08h 8 BYTEs for types "D" and "I", base name of file from which the driver was loaded (unused for other types) Format of data at start of STACKS code segment (if present): Offset Size Description (Table 0846) 00h WORD ??? 02h WORD number of stacks (the x in STACKS=x,y) 04h WORD size of stack control block array (should be 8*x) 06h WORD size of each stack (the y in STACKS=x,y) 08h DWORD pointer to STACKS data segment 0Ch WORD offset in STACKS data segment of stack control block array 0Eh WORD offset in STACKS data segment of last element of that array 10h WORD offset in STACKS data segment of the entry in that array for the next stack to be allocated (initially same as value in 0Eh and works its way down in steps of 8 to the value in 0Ch as hardware interrupts pre-empt each other) Note: the STACKS code segment data may, if present, be located as follows: DOS 3.2: The code segment data is at a paragraph boundary fairly early in the IBMBIO segment (seen at 0070:0190h) DOS 3.3: The code segment is at a paragraph boundary in the DOS data segment, which may be determined by inspecting the segment pointers of the vectors for those of interrupts 02h, 08h-0Eh, 70h, 72-77h which have not been redirected by device drivers or TSRs. DOS 4.0+ Identified by sub-segment control block type "S" within the DOS data segment. SeeAlso: #0848,INT B4"STACKMAN" Format of array elements in STACKS data segment: Offset Size Description (Table 0847) 00h BYTE status: 00h=free, 01h=in use, 03h=corrupted by overflow of higher stack. 01h BYTE not used 02h WORD previous SP 04h WORD previous SS 06h WORD ptr to word at top of stack (new value for SP). The word at the top of the stack is preset to point back to this control block. Format of SHARE.EXE hooks (DOS 3.1-6.00): Offset Size Description (Table 0848) (offsets from first system file table--pointed at by ListOfLists+04h) -3Ch DWORD pointer to FAR routine for ??? Note: not called by MS-DOS 3.3, set to 0000h:0000h by SHARE 3.3+ -38h DWORD pointer to FAR routine called on opening file on call, internal DOS location points at filename (see #0892 at AX=5D06h) Return: CF clear if successful CF set on error AX = DOS error code (24h) (see #0885 at AH=59h) Note: SHARE directly accesses DOS-internal data to get name of file just opened -34h DWORD pointer to FAR routine called on closing file ES:DI -> system file table Note: does something to every Record Lock Record for file -30h DWORD pointer to FAR routine to close all files for given computer (called by AX=5D03h) -2Ch DWORD pointer to FAR routine to close all files for given process (called by AX=5D04h) -28h DWORD pointer to FAR routine to close file by name (called by AX=5D02h) DS:SI -> DOS parameter list (see #0891 at AX=5D00h) DPL's DS:DX -> name of file to close Return: CF clear if successful CF set on error AX = DOS error code (03h) (see #0885 at AH=59h) -24h DWORD pointer to FAR routine to lock region of file call with BX = file handle ---DOS 3.x--- CX:DX = starting offset SI:AX = size ---DOS 4.0+ --- DS:DX -> lock range DWORD start offset DWORD size in bytes Return: CF set on error AL = DOS error code (21h) (see #0885 at AH=59h) Note: not called if file is marked as remote -20h DWORD pointer to FAR routine to unlock region of file call with BX = file handle ---DOS 3.x--- CX:DX = starting offset SI:AX = size ---DOS 4.0+ --- DS:DX -> lock range DWORD start offset DWORD size in bytes Return: CF set on error AL = DOS error code (21h) (see #0885 at AH=59h) Note: not called if file is marked as remote -1Ch DWORD pointer to FAR routine to check if file region is locked call with ES:DI -> system file table entry for file CX = length of region from current position in file Return: CF set if any portion of region locked AX = 0021h -18h DWORD pointer to FAR routine to get open file list entry (called by AX=5D05h) call with DS:SI -> DOS parameter list (see #0891 at AX=5D00h) DPL's BX = index of sharing record DPL's CX = index of SFT in SFT chain of sharing rec Return: CF set on error or not loaded AX = DOS error code (12h) (see #0885 at AH=59h) CF clear if successful ES:DI -> filename CX = number of locks owned by specified SFT BX = network machine number DX destroyed -14h DWORD pointer to FAR routine for updating FCB from SFT??? call with DS:SI -> unopened FCB ES:DI -> system file table entry Return: BL = C0h??? Note: copies following fields from SFT to FCB: starting cluster of file 0Bh 1Ah sharing record offset 33h 1Ch file attribute 04h 1Eh -10h DWORD pointer to FAR routine to get first cluster of FCB file ??? call with ES:DI -> system file table entry DS:SI -> FCB Return: CF set if SFT closed or sharing record offsets mismatched CF clear if successful BX = starting cluster number from FCB -0Ch DWORD pointer to FAR routine to close file if duplicate for process DS:SI -> system file table Return: AX = number of handle in JFT which already uses SFT Note: called during open/create of a file Note: if SFT was opened with inheritance enabled and sharing mode 111, does something to all other SFTs owned by same process which have the same file open mode and sharing record -08h DWORD pointer to FAR routine for closing file Note: closes various handles referring to file most-recently opened -04h DWORD pointer to FAR routine to update directory info in related SFT entries call with ES:DI -> system file table entry for file (see #0853) AX = subfunction (apply to each related SFT) 00h: update time stamp (offset 0Dh) and date stamp (offset 0Fh) 01h: update file size (offset 11h) and starting cluster (offset 0Bh). Sets last-accessed cluster fields to start of file if file never accessed 02h: as function 01h, but last-accessed fields always changed 03h: do both functions 00h and 02h Note: follows ptr at offset 2Bh in system file table entries Note: NOP if opened with no-inherit or via FCB Notes: most of the above hooks (except -04h, -14h, -18h, and -3Ch) assume either that SS=DOS DS or SS=DS=DOS DS and directly access DOS-internal data sharing hooks are not supported by DR-DOS 5-6; they appear to be supported by Novell DOS 7, with a segment of 0000h indicating the DOS data segment SeeAlso: #0849,#0850 Format of sharing record: Offset Size Description (Table 0849) 00h BYTE flag 00h free block 01h allocated block FFh end marker 01h WORD size of block 03h BYTE checksum of pathname (including NUL) if sum of ASCII values is N, checksum is (N/256 + N%256) 04h WORD offset in SHARE's DS of first Record Lock Record (see #0850) 06h DWORD pointer to start of system file table chain for file 0Ah WORD unique sequence number 0Ch var ASCIZ full pathname Note: not supported by DR-DOS SHARE 1.1 and 2.0; will reportedly be supported by Novell DOS 7 SeeAlso: #0848,#0850 Format of SHARE.EXE Record Lock Record: Offset Size Description (Table 0850) 00h WORD offset in SHARE's DS of next lock table in list or 0000h 02h DWORD offset in file of start of locked region 06h DWORD offset in file of end of locked region 0Ah DWORD pointer to System File Table entry for this file 0Eh WORD PSP segment of lock's owner ---DOS 5+ --- 10h WORD lock type: (00h lock all, 01h lock writes only) SeeAlso: #0848,#0849,#0851,#0854 Format of DOS 2.x system file tables: Offset Size Description (Table 0851) 00h DWORD pointer to next file table (offset FFFFh if last) 04h WORD number of files in this table 06h 28h bytes per file Offset Size Description 00h BYTE number of file handles referring to this file 01h BYTE file open mode (see #0627 at AH=3Dh) 02h BYTE file attribute 03h BYTE drive (0 = character device, 1 = A, 2 = B, etc) 04h 11 BYTEs filename in FCB format (no path,no period,blank-padded) 0Fh WORD ??? 11h WORD ??? 13h DWORD file size??? 17h WORD file date in packed format (see #0877 at AX=5700h) 19h WORD file time in packed format (see #0876 at AX=5700h) 1Bh BYTE device attribute (see #0646 at AX=4400h) ---character device--- 1Ch DWORD pointer to device driver ---block device--- 1Ch WORD starting cluster of file 1Eh WORD relative cluster in file of last cluster accessed ------ 20h WORD absolute cluster number of current cluster 22h WORD ??? 24h DWORD current file position??? SeeAlso: #0852,#0853,#0854 Format of DOS 3.0 system file tables and FCB tables: Offset Size Description (Table 0852) 00h DWORD pointer to next file table (offset FFFFh if last) 04h WORD number of files in this table 06h 38h bytes per file Offset Size Description 00h-1Eh as for DOS 3.1+ (see #0853) 1Fh WORD byte offset of directory entry within sector 21h 11 BYTEs filename in FCB format (no path/period, blank-padded) 2Ch DWORD (SHARE.EXE) pointer to previous SFT sharing same file 30h WORD (SHARE.EXE) network machine number which opened file (Windows Enhanced mode DOSMGR uses the virtual machine ID as the machine number; see INT 2F/AX=1683h) 32h WORD PSP segment of file's owner (first three entries for AUX/CON/PRN contain segment of IO.SYS startup code) 34h WORD (SHARE.EXE) offset in SHARE code seg of share record 36h WORD ??? apparently always 0000h SeeAlso: #0851,#0853,#0854 Format of DOS 3.1-3.3x, DR-DOS 5.0-6.0 system file tables and FCB tables: Offset Size Description (Table 0853) 00h DWORD pointer to next file table (offset FFFFh if last) 04h WORD number of files in this table 06h 35h bytes per file Offset Size Description 00h WORD number of file handles referring to this file 02h WORD file open mode (see AX=6C00h, #0627 at AH=3Dh) bit 15 set if this file opened via FCB 04h BYTE file attribute (see #0643 at AX=4301h) 05h WORD device info word (see #0646 at AX=4400h) bit 15 set if remote file bit 14 set means do not set file date/time on closing bit 12 set means don't inherit on EXEC bits 5-0 drive number for disk files 07h DWORD pointer to device driver header if character device else pointer to DOS Drive Parameter Block (see #0620 at AH=32h) 0Bh WORD starting cluster of file 0Dh WORD file time in packed format (see #0876 at AX=5700h) not used for character devices in DR-DOS 0Fh WORD file date in packed format (see #0877 at AX=5700h) not used for character devices in DR-DOS 11h DWORD file size ---system file table--- 15h DWORD current offset in file (may be larger than size of file; INT 21/AH=42h does not check new position) ---FCB table--- 15h WORD counter for last I/O to FCB 17h WORD counter for last open of FCB (these are separate to determine the times of the latest I/O and open) --- 19h WORD relative cluster within file of last cluster accessed 1Bh WORD absolute cluster number of last cluster accessed 0000h if file never read or written??? 1Dh WORD number of sector containing directory entry 1Fh BYTE number of dir entry within sector (byte offset/32) 20h 11 BYTEs filename in FCB format (no path/period, blank-padded) 2Bh DWORD (SHARE.EXE) pointer to previous SFT sharing same file 2Fh WORD (SHARE.EXE) network machine number which opened file (Windows Enhanced mode DOSMGR uses the virtual machine ID as the machine number; see INT 2F/AX=1683h) 31h WORD PSP segment of file's owner (see #0603 at AH=26h) (first three entries for AUX/CON/PRN contain segment of IO.SYS startup code) 33h WORD offset within SHARE.EXE code segment of sharing record (see #0849) 0000h = none SeeAlso: #0851,#0852,#0854 Format of DOS 4.0-6.0 system file tables and FCB tables: Offset Size Description (Table 0854) 00h DWORD pointer to next file table (offset FFFFh if last) 04h WORD number of files in this table 06h 3Bh bytes per file Offset Size Description 00h WORD number of file handles referring to this file FFFFh if in use but not referenced 02h WORD file open mode (see AX=6C00h,#0627 at AH=3Dh) bit 15 set if this file opened via FCB 04h BYTE file attribute (see #0643 at AX=4301h) 05h WORD device info word (see also #0646 at AX=4400h) bit 15 set if remote file bit 14 set means do not set file date/time on closing bit 13 set if named pipe bit 12 set if no inherit bit 11 set if network spooler bit 7 set if device, clear if file (only if local) bits 6-0 as for AX=4400h 07h DWORD pointer to device driver header if character device else pointer to DOS Drive Parameter Block (see #0620 at AH=32h) or REDIR data 0Bh WORD starting cluster of file (local files only) 0Dh WORD file time in packed format (see #0876) 0Fh WORD file date in packed format (see #0877) 11h DWORD file size 15h DWORD current offset in file (SFT) LRU counters (FCB table, two WORDs) ---local file--- 19h WORD relative cluster within file of last cluster accessed 1Bh DWORD number of sector containing directory entry 1Fh BYTE number of dir entry within sector (byte offset/32) ---network redirector--- 19h DWORD pointer to REDIRIFS record 1Dh 3 BYTEs ??? ------ 20h 11 BYTEs filename in FCB format (no path/period, blank-padded) 2Bh DWORD (SHARE.EXE) pointer to previous SFT sharing same file 2Fh WORD (SHARE.EXE) network machine number which opened file (Windows Enhanced mode DOSMGR uses the virtual machine ID as the machine number; see INT 2F/AX=1683h) 31h WORD PSP segment of file's owner (see #0603 at AH=26h) (first three entries for AUX/CON/PRN contain segment of IO.SYS startup code) 33h WORD offset within SHARE.EXE code segment of sharing record (see #0808) 0000h = none 35h WORD (local) absolute cluster number of last clustr accessed (redirector) ??? 37h DWORD pointer to IFS driver for file, 0000000h if native DOS Note: the OS/2 2.0 DOS Boot Session does not properly fill in the filename field due to incomplete support for SFTs; the OS/2 2.0 DOS Window does not appear to support SFTs at all SeeAlso: #0851,#0852,#0853 Format of current directory structure (CDS) (array, LASTDRIVE entries): Offset Size Description (Table 0855) 00h 67 BYTEs ASCIZ path in form X:\PATH (local) or UNC form \\SERVER\PATH (network, see notes below) 43h WORD drive attributes (see also note below and AX=5F07h) bit 15: uses network redirector \ invalid if 00, installable bit 14: physical drive / file system if 11 bit 13: JOIN'ed \ path above is true path that would be bit 12: SUBST'ed / needed if not under SUBST or JOIN bit 7: remote drive hidden from redirector's assign-list and exempt from network connection make/break commands; set for CD-ROM drives 45h DWORD pointer to Drive Parameter Block for drive (see #0620 at AH=32h) ---local drives--- 49h WORD starting cluster of current directory 0000h = root, FFFFh = never accessed 4Bh WORD ??? seems to be FFFFh always 4Dh WORD ??? seems to be FFFFh always ---network drives--- 49h DWORD pointer to redirector or REDIRIFS record, or FFFFh:FFFFh (DOS 4 only) available for use by IFS driver 4Dh WORD stored user data from INT 21/AX=5F03h ------ 4Fh WORD offset in current directory path of backslash corresponding to root directory for drive this value specifies how many characters to hide from the "CHDIR" and "GETDIR" calls; normally set to 2 to hide the drive letter and colon, SUBST, JOIN, and networks change it so that only the appropriate portion of the true path is visible to the user ---DOS 4.0+ --- 51h BYTE (DOS 4 only, remote drives) device type 04h network drive 52h DWORD pointer to IFS driver (DOS 4) or redirector block (DOS 5+) for this drive, 00000000h if native DOS 56h WORD available for use by IFS driver Notes: the path for invalid drives is normally set to X:\, but may be empty after JOIN x: /D in DR-DOS 5.0 or NET USE x: /D in older LAN versions normally, only one of bits 13&12 may be set together with bit 14, but DR-DOS 5.0 uses other combinations for bits 15-12: 0111 JOIN, 0001 SUBST, 0101 ASSIGN (see #0856) Windows for Workgroups 3.11 network sets the path to the local drive and directory even for network drives; in that case the UNC form \\SERVER\SHARE can be obtained with INT 21/AX=5F02h or INT 21/AX=5F46h. LapLink RemoteAccess does the same even for INT 21/AX=5F02h SoftWindows on the Macintosh PowerPC sets \\E for the host drive SeeAlso: #0856 Format of DR-DOS 5.0-6.0 current directory structure entry (array): Offset Size Description (Table 0856) 00h 67 BYTEs ASCIZ pathname of actual root directory for this logical drive 43h WORD drive attributes 1000h SUBSTed drive 3000h??? JOINed drive 4000h physical drive 5000h ASSIGNed drive 7000h JOINed drive 8000h network drive 45h BYTE physical drive number (0=A:) if this logical drive is valid 46h BYTE ??? apparently flags for JOIN and ASSIGN 47h WORD cluster number of start of parent directory (0000h = root) 49h WORD entry number of current directory in parent directory 4Bh WORD cluster number of start of current directory 4Dh WORD used for media change detection (details not available) 4Fh WORD cluster number of SUBST/JOIN "root" directory 0000h if physical root directory SeeAlso: #0855 Format of Windows NT Current Directory Structure (CDS) (array): Offset Size Description (Table 0857) 00h 67 BYTEs ASCIZ path in form X:\ (does not show either current directory or network path) 43h 4 BYTEs ??? Note: the WinNT CDS contains only as many entries as there are local drives, not LASTDRIVE entries. Format of DOS device driver header: Offset Size Description (Table 0858) 00h DWORD pointer to next driver, offset=FFFFh if last driver 04h WORD device attributes (see #0859,#0860) 06h WORD device strategy entry point call with ES:BX -> request header (see #1382 at INT 2F/AX=0802h) 08h WORD device interrupt entry point ---character device--- 0Ah 8 BYTEs blank-padded character device name ---block device--- 0Ah BYTE number of subunits (drives) supported by driver 0Bh 7 BYTEs normally unused; sometimes contains signature to indicate specific drivers: "GFS " LapLink III device driver DD.BIN "STAC-CD" Stacker/Stacker Anywhere (see AX=4404h"Stacker") "SIDExxx" PCMCIA driver ATADRV.EXE (see AX=440Dh) "$PCMATA" PCMCIA driver PCMATA.SYS (see AX=440Dh) "DSKREET" NortonUtils v5+ Diskreet (see INT 2F/AX=FE00h) "DBLSPAC" MS DoubleSpace or DriveSpace ---DoubleSpace/DriveSpace--- 12h 2 BYTEs signature ",." (2Ch 2Eh) 14h var preloading API entry point ---CD-ROM--- 12h WORD reserved, must be 0000h appears to be another device chain 14h BYTE drive letter (must initially be 00h; this byte is set by MSCDEX when it loads) 15h BYTE number of units 16h 6 BYTEs signature 'MSCDnn' where 'nn' is version (currently '00') SeeAlso: #1341 at INT 25/AX=CDCDh,#1557 at INT 2F/AX=5600h Bitfields for device attributes (character device): Bit(s) Description (Table 0859) 15 set (indicates character device) 14 IOCTL supported (see AH=44h) 13 (DOS 3.0+) output until busy supported 12 reserved 11 (DOS 3.0+) OPEN/CLOSE/RemMedia calls supported 10-8 reserved 7 (DOS 5.0+) Generic IOCTL check call supported (driver command 19h) (see AX=4410h,AX=4411h) 6 (DOS 3.2+) Generic IOCTL call supported (driver command 13h) (see AX=440Ch,AX=440Dh) 5 reserved 4 device is special (use INT 29 "fast console output") 3 device is CLOCK$ (all reads/writes use transfer record described below) 2 device is NUL 1 device is standard output 0 device is standard input Note: for European MS-DOS 4.0, bit 11 also indicates that bits 8-6 contain a version code (000 = DOS 3.0,3.1; 001 = DOS 3.2; 010 = European DOS 4.0) SeeAlso: #0860,#0858 Bitfields for device attributes (block device): Bit(s) Description (Table 0860) 15 clear (indicates block device) 14 IOCTL supported 13 non-IBM format 12 network device (device is remote) 11 (DOS 3.0+) OPEN/CLOSE/RemMedia calls supported 10 reserved 9 direct I/O not allowed??? (set by DOS 3.3 DRIVER.SYS for "new" drives) 8 ??? set by DOS 3.3 DRIVER.SYS for "new" drives 7 (DOS 5.0+) Generic IOCTL check call supported (driver command 19h) (see AX=4410h,AX=4411h) 6 (DOS 3.2+) Generic IOCTL call supported (driver command 13h) implies support for commands 17h and 18h (see AX=440Ch,AX=440Dh,AX=440Eh,AX=440Fh) 5-2 reserved 1 driver supports 32-bit sector addressing (DOS 3.31+) 0 reserved Note: for European MS-DOS 4.0, bit 11 also indicates that bits 8-6 contain a version code (000 = DOS 3.0,3.1; 001 = DOS 3.2; 010 = European DOS 4.0) SeeAlso: #0859,#0858 Format of DOS 2.x disk buffer: Offset Size Description (Table 0861) 00h DWORD pointer to next disk buffer, offset = FFFFh if last least-recently used buffer is first in chain 04h BYTE drive (0=A, 1=B, etc), FFh if not in use 05h 3 BYTEs unused??? (seems always to be 00h 00h 01h) 08h WORD logical sector number 0Ah BYTE number of copies to write (1 for non-FAT sectors) 0Bh BYTE sector offset between copies if multiple copies to be written 0Ch DWORD pointer to DOS Drive Parameter Block (see #0620 at AH=32h) 10h buffered data SeeAlso: #0862,#0864,#0865,#0867 Format of DOS 3.x disk buffer: Offset Size Description (Table 0862) 00h DWORD pointer to next disk buffer, offset = FFFFh if last least-recently used buffer is first in chain 04h BYTE drive (0=A,1=B, etc), FFh if not in use 05h BYTE buffer flags (see #0863) 06h WORD logical sector number 08h BYTE number of copies to write (1 for non-FAT sectors) 09h BYTE sector offset between copies if multiple copies to be written 0Ah DWORD pointer to DOS Drive Parameter Block (see #0620 at AH=32h) 0Eh WORD unused??? (almost always 0) 10h buffered data SeeAlso: #0861,#0864,#0865,#0867 Bitfields for DOS 3.x disk buffer flags: Bit(s) Description (Table 0863) 7 ??? 6 buffer dirty 5 buffer has been referenced 4 ??? 3 sector in data area 2 sector in a directory, either root or subdirectory 1 sector in FAT 0 boot sector??? (guess) SeeAlso: #0868 Format of DOS 4.00 (pre UR 25066) disk buffer info: Offset Size Description (Table 0864) 00h DWORD pointer to array of disk buffer hash chain heads (see #0866) 04h WORD number of disk buffer hash chains (referred to as NDBCH below) 06h DWORD pointer to lookahead buffer, zero if not present 0Ah WORD number of lookahead sectors, else zero (the y in BUFFERS=x,y) 0Ch BYTE 00h if buffers in EMS (/X), FFh if not 0Dh WORD EMS handle for buffers, zero if not in EMS 0Fh WORD EMS physical page number used for buffers (usually 255) 11h WORD ??? seems always to be 0001h 13h WORD segment of EMS physical page frame 15h WORD ??? seems always to be zero 17h 4 WORDs EMS partial page mapping information??? SeeAlso: #0861,#0862,#0865,#0869 Format of DOS 4.01 (from UR 25066 Corrctive Services Disk on) disk buffer info: Offset Size Description (Table 0865) 00h DWORD pointer to array of disk buffer hash chain heads (see #0866) 04h WORD number of disk buffer hash chains (referred to as NDBCH below) 06h DWORD pointer to lookahead buffer, zero if not present 0Ah WORD number of lookahead sectors, else zero (the y in BUFFERS=x,y) 0Ch BYTE 01h, possibly to distinguish from pre-UR 25066 format 0Dh WORD ??? EMS segment for BUFFERS (only with /XD) 0Fh WORD ??? EMS physical page number of EMS seg above (only with /XD) 11h WORD ??? EMS segment for ??? (only with /XD) 13h WORD ??? EMS physical page number of above (only with /XD) 15h BYTE ??? number of EMS page frames present (only with /XD) 16h WORD segment of one-sector workspace buffer allocated in main memory if BUFFERS/XS or /XD options in effect, possibly to avoid DMA into EMS 18h WORD EMS handle for buffers, zero if not in EMS 1Ah WORD EMS physical page number used for buffers (usually 255) 1Ch WORD ??? appears always to be 0001h 1Eh WORD segment of EMS physical page frame 20h WORD ??? appears always to be zero 22h BYTE 00h if /XS, 01h if /XD, FFh if BUFFERS not in EMS SeeAlso: #0861,#0862,#0864,#0869 Format of DOS 4.x disk buffer hash chain head (array, one entry per chain): Offset Size Description (Table 0866) 00h WORD EMS logical page number in which chain is resident, -1 if not in EMS 02h DWORD pointer to least recently used buffer header. All buffers on this chain are in the same segment. 06h BYTE number of dirty buffers on this chain 07h BYTE reserved (00h) Notes: buffered disk sectors are assigned to chain N where N is the sector's address modulo NDBCH, 0 <= N <= NDBCH-1 each chain resides completely within one EMS page this structure is in main memory even if buffers are in EMS Format of DOS 4.0-6.0 disk buffer: Offset Size Description (Table 0867) 00h WORD forward ptr, offset only, to next least recently used buffer 02h WORD backward pointer, offset only 04h BYTE drive (0=A,1=B, etc) if bit 7 clear SFT index if bit 7 set FFh if not in use 05h BYTE buffer flags (see #0868) 06h DWORD logical sector number (local buffers only) 0Ah BYTE number of copies to write for FAT sectors, same as number of FATs for data and directory sectors, usually 1 0Bh WORD offset in sectors between copies to write for FAT sectors 0Dh DWORD pointer to DOS Drive Parameter Block (see #0620 at AH=32h) 11h WORD size of data in buffer if remote buffer (see flags above) 13h BYTE reserved (padding) 14h buffered data Note: for DOS 4.x, all buffered sectors which have the same hash value (computed as the sum of high and low words of the logical sector number divided by the number of disk buffer chains) are on the same doubly-linked circular chain; for DOS 5+, only a single circular chain exists. the links consist of offset addresses only, the segment being the same for all buffers in the chain. SeeAlso: #0861,#0862,#0864 Bitfields for DOS 4.0-6.0 disk buffer flags: Bit(s) Description (Table 0868) 7 remote buffer 6 buffer dirty 5 buffer has been referenced (reserved in DOS 5+) 4 search data buffer (only valid if remote buffer) 3 sector in data area 2 sector in a directory, either root or subdirectory 1 sector in FAT 0 reserved SeeAlso: #0863 Format of DOS 5.0-6.0 disk buffer info: Offset Size Description (Table 0869) 00h DWORD pointer to least-recently-used buffer header (may be in HMA) (see #0867) 04h WORD number of dirty disk buffers 06h DWORD pointer to lookahead buffer, zero if not present 0Ah WORD number of lookahead sectors, else zero (the y in BUFFERS=x,y) 0Ch BYTE buffer location 00h base memory, no workspace buffer 01h HMA, workspace buffer in base memory 0Dh DWORD pointer to one-segment workspace buffer in base memory 11h 3 BYTEs unused 14h WORD ??? 16h BYTE flag: INT 24 fail while making an I/O status call 17h BYTE temp storage for user memory allocation strategy during EXEC 18h BYTE counter: number of INT 21 calls for which A20 is off 19h BYTE bit flags bit 0: ??? bit 1: SWITCHES=/W specified in CONFIG.SYS (don't load WINA20.SYS when MS Windows 3.0 starts) bit 2: in EXEC state (INT 21/AX=4B05h) 1Ah WORD offset of unpack code start (used only during INT 21/AX=4B05h) 1Ch BYTE bit 0 set iff UMB MCB chain linked to normal MCB chain 1Dh WORD minimum paragraphs of memory required by program being EXECed 1Fh WORD segment of first MCB in upper memory blocks or FFFFh if DOS memory chain in base 640K only (first UMB MCB usually at 9FFFh, locking out video memory with a DOS-owned memory block) the MCB this word points at contains a valid link into high memory even if it is marked with a 'Z' indicating the last memory block 21h WORD paragraph from which to start scanning during memory allocation SeeAlso: #0864,#0865 (Table 0870) Call IFS utility function entry point with: AH = 20h miscellaneous functions AL = 00h get date Return: CX = year DH = month DL = day AL = 01h get process ID and computer ID Return: BX = current PSP segment DX = active network machine number AL = 05h get file system info ES:DI -> 16-byte info buffer Return: buffer filled Offset Size Description 00h 2 BYTEs unused 02h WORD number of SFTs (actually counts only the first two file table arrays) 04h WORD number of FCB table entries 06h WORD number of proctected FCBs 08h 6 BYTEs unused 0Eh WORD largest sector size supported AL = 06h get machine name ES:DI -> 18-byte buffer for name Return: buffer filled with name starting at offset 02h AL = 08h get sharing retry count Return: BX = sharing retry count AL = other Return: CF set AH = 21h get redirection state BH = type (03h disk, 04h printer) Return: BH = state (00h off, 01h on) AH = 22h ??? some sort of time calculation AL = 00h ??? nonzero ??? AH = 23h ??? some sort of time calculation AH = 24h compare filenames DS:SI -> first ASCIZ filename ES:DI -> second ASCIZ filename Return: ZF set if files are same ignoring case and / vs \ AH = 25h normalize filename DS:SI -> ASCIZ filename ES:DI -> buffer for result Return: filename uppercased, forward slashes changed to backslashes AH = 26h get DOS stack Return: DS:SI -> top of stack CX = size of stack in bytes AH = 27h increment InDOS flag AH = 28h decrement InDOS flag Note: IFS drivers which do not wish to implement functions 20h or 24h-28h may pass them on to the default handler pointed at by [LoL+37h] SeeAlso: #0871,#0872 Format of IFS driver list: Offset Size Description (Table 0871) 00h DWORD pointer to next driver header 04h 8 BYTEs IFS driver name (blank padded), as used by FILESYS command 0Ch 4 BYTEs ??? 10h DWORD pointer to IFS utility function entry point (see #0870) call with ES:BX -> IFS request (see #0872) 14h WORD offset in header's segment of driver entry point ??? SeeAlso: #0870,#0872 Format of IFS request block: Offset Size Description (Table 0872) 00h WORD total size in bytes of request 02h BYTE class of request 02h ??? 03h redirection 04h ??? 05h file access 06h convert error code to string 07h ??? 03h WORD returned DOS error code 05h BYTE IFS driver exit status 00h success 01h ??? 02h ??? 03h ??? 04h ??? FFh internal failure 06h 16 BYTEs ??? ---request class 02h--- 16h BYTE function code 04h ??? 17h BYTE unused??? 18h DWORD pointer to ??? 1Ch DWORD pointer to ??? 20h 2 BYTEs ??? ---request class 03h--- 16h BYTE function code 17h BYTE ??? 18h DWORD pointer to ??? 1Ch DWORD pointer to ??? 22h WORD returned ??? 24h WORD returned ??? 26h WORD returned ??? 28h BYTE returned ??? 29h BYTE unused??? ---request class 04h--- 16h DWORD pointer to ??? 1Ah DWORD pointer to ??? ---request class 05h--- 16h BYTE function code 01h flush disk buffers 02h get disk space 03h MKDIR 04h RMDIR 05h CHDIR 06h delete file 07h rename file 08h search directory 09h file open/create 0Ah LSEEK 0Bh read from file 0Ch write to file 0Dh lock region of file 0Eh commit/close file 0Fh get/set file attributes 10h printer control 11h ??? 12h process termination 13h ??? ---class 05h function 01h--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h 4 BYTEs ??? 26h BYTE ??? 27h BYTE ??? ---class 05h function 02h--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h 4 BYTEs ??? 26h WORD returned total clusters 28h WORD returned sectors per cluster 2Ah WORD returned bytes per sector 2Ch WORD returned available clusters 2Eh BYTE returned ??? 2Fh BYTE ??? ---class 05h functions 03h,04h,05h--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h 4 BYTEs ??? 26h DWORD pointer to directory name ---class 05h function 06h--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h 4 BYTEs ??? 26h WORD attribute mask 28h DWORD pointer to filename ---class 05h function 07h--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h 4 BYTEs ??? 26h WORD attribute mask 28h DWORD pointer to source filespec 2Ch DWORD pointer to destination filespec ---class 05h function 08h--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h 4 BYTEs ??? 26h BYTE 00h FINDFIRST 01h FINDNEXT 28h DWORD pointer to FindFirst search data + 01h if FINDNEXT 2Ch WORD search attribute if FINDFIRST 2Eh DWORD pointer to filespec if FINDFIRST ---class 05h function 09h--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h DWORD pointer to IFS open file structure (see #0873) 26h WORD ??? \ together, specify open vs. create, whether or 28h WORD ??? / not to truncate 2Ah 4 BYTEs ??? 2Eh DWORD pointer to filename 32h 4 BYTEs ??? 36h WORD file attributes on call returned ??? 38h WORD returned ??? ---class 05h function 0Ah--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h DWORD pointer to IFS open file structure (see #0873) 26h BYTE seek type (02h = from end) 28h DWORD offset on call returned new absolute position ---class 05h functions 0Bh,0Ch--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h DWORD pointer to IFS open file structure (see #0873) 28h WORD number of bytes to transfer returned bytes actually transferred 2Ah DWORD transfer address ---class 05h function 0Dh--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h DWORD pointer to IFS open file structure (see #0873) 26h BYTE file handle??? 27h BYTE unused??? 28h WORD ??? 2Ah WORD ??? 2Ch WORD ??? 2Eh WORD ??? ---class 05h function 0Eh--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h DWORD pointer to IFS open file structure (see #0873) 26h BYTE 00h commit file 01h close file 27h BYTE unused??? ---class 05h function 0Fh--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h 4 BYTEs ??? 26h BYTE 02h GET attributes 03h PUT attributes 27h BYTE unused??? 28h 12 BYTEs ??? 34h WORD search attributes??? 36h DWORD pointer to filename 3Ah WORD (GET) returned ??? 3Ch WORD (GET) returned ??? 3Eh WORD (GET) returned ??? 40h WORD (GET) returned ??? 42h WORD (PUT) new attributes (GET) returned attributes ---class 05h function 10h--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h DWORD pointer to IFS open file structure (see #0873) 26h WORD ??? 28h DWORD pointer to ??? 2Ch WORD ??? 2Eh BYTE ??? 2Fh BYTE subfunction 01h get printer setup 03h ??? 04h ??? 05h ??? 06h ??? 07h ??? 21h set printer setup ---class 05h function 11h--- 17h 7 BYTEs ??? 1Eh DWORD pointer to ??? 22h DWORD pointer to IFS open file structure (see #0873) 26h BYTE subfunction 27h BYTE unused??? 28h WORD ??? 2Ah WORD ??? 2Ch WORD ??? 2Eh BYTE ??? 2Fh BYTE ??? ---class 05h function 12h--- 17h 15 BYTEs unused??? 26h WORD PSP segment 28h BYTE type of process termination 29h BYTE unused??? ---class 05h function 13h--- 17h 15 BYTEs unused??? 26h WORD PSP segment ---request class 06h--- 16h DWORD returned pointer to string corresponding to error code at 03h 1Ah BYTE returned ??? 1Bh BYTE unused ---request class 07h--- 16h DWORD pointer to IFS open file structure (see #0873) 1Ah BYTE ??? 1Bh BYTE unused??? SeeAlso: #0871,#0870,#0873 Format of IFS open file structure: Offset Size Description (Table 0873) 00h WORD ??? 02h WORD device info word 04h WORD file open mode 06h WORD ??? 08h WORD file attributes 0Ah WORD owner's network machine number 0Ch WORD owner's PSP segment 0Eh DWORD file size 12h DWORD current offset in file 16h WORD file time 18h WORD file date 1Ah 11 BYTEs filename in FCB format 25h WORD ??? 27h WORD hash value of SFT address (low word of linear address + segment&F000h) 29h 3 WORDs network info from SFT 2Fh WORD ??? Format of one item in DOS 4.0+ list of special program names: Offset Size Description (Table 0874) 00h BYTE length of name (00h = end of list) 01h N BYTEs name in format name.ext N 2 BYTEs DOS version to return for program (major,minor) (see AH=30h,INT 2F/AX=122Fh) ---DOS 4 only--- N+2 BYTE number of times to return fake version number (FFh = always) Note: if the name of the executable for the program making the DOS "get version" call matches one of the names in this list, DOS returns the specified version rather than the true version number --------v-215252----------------------------- INT 21 - VIRUS - "516"/"Leapfrog" - INSTALLATION CHECK AX = 5252h Return: BX = FFEEh if resident SeeAlso: AX=4BFFh"Cascade",AX=58CCh --------D-2153------------------------------- INT 21 - DOS 2+ internal - TRANSLATE BIOS PARAMETER BLOCK TO DRIVE PARAM BLOCK AH = 53h DS:SI -> BIOS Parameter Block (see #0875) ES:BP -> buffer for Drive Parameter Block (see #0620 at AH=32h) Return: ES:BP buffer filled Notes: for DOS 3.0+, the cluster at which to start searching is set to 0000h and the number of free clusters is set to FFFFh (unknown) if the number of sectors per cluster is set to zero, MS-DOS will hang at startup because it computes the internally-used shift count by shifting this value right until the carry flag is set; since this will never happen when the field is zero, MS-DOS hangs Format of BIOS Parameter Block: Offset Size Description (Table 0875) 00h WORD number of bytes per sector 02h BYTE number of sectors per cluster 03h WORD number of reserved sectors at start of disk 05h BYTE number of FATs 06h WORD number of entries in root directory 08h WORD total number of sectors for DOS 4.0+, set to zero if partition >32M, then set DWORD at 15h to actual number of sectors 0Ah BYTE media ID byte (see #0581) 0Bh WORD number of sectors per FAT ---DOS 2.13--- 0Dh WORD number of sectors per track 0Fh WORD number of heads 11h WORD number of hidden sectors ---DOS 3.0+ --- 0Dh WORD number of sectors per track 0Fh WORD number of heads 11h DWORD number of hidden sectors 15h 11 BYTEs reserved ---DOS 4.0+ --- 15h DWORD total number of sectors if word at 08h contains zero 19h 6 BYTEs ??? 1Fh WORD number of cylinders 21h BYTE device type 22h WORD device attributes (removable or not, etc) ---DR-DOS 5+ --- 15h DWORD total number of sectors if word at 08h contains zero 19h 6 BYTEs reserved ---European MS-DOS 4.00--- 15h DWORD total number of sectors if word at 08h contains zero (however, this DOS does not actually implement >32M partitions) SeeAlso: #0620 --------D-2154------------------------------- INT 21 - DOS 2+ - GET VERIFY FLAG AH = 54h Return: AL = verify flag 00h off 01h on (all disk writes verified after writing) SeeAlso: AH=2Eh --------D-2155------------------------------- INT 21 - DOS 2+ internal - CREATE CHILD PSP AH = 55h DX = segment at which to create new PSP SI = (DOS 3.0+) value to place in memory size field at DX:[0002h] Return: CF clear if successful Notes: creates a "child" PSP rather than making an exact copy of the current PSP; the new PSP's parent pointer is set to the current PSP and the reference count for each inherited file is incremented (DOS 2.0+) sets current PSP to DX (DOS 3.0+) marks "no inherit" file handles as closed in child PSP BUG: OS/2 Warp's DOS box does not clear CF on success, instead leaving it in its former state; to work around this, ensure that CF is clear before calling SeeAlso: AH=26h,AH=50h --------D-2156------------------------------- INT 21 - DOS 2+ - "RENAME" - RENAME FILE AH = 56h DS:DX -> ASCIZ filename of existing file (no wildcards, but see below) ES:DI -> ASCIZ new filename (no wildcards) CL = attribute mask (server call only, see below) Return: CF clear if successful CF set on error AX = error code (02h,03h,05h,11h) (see #0885) Notes: allows move between directories on same logical volume this function does not set the archive attribute (see #0643 at AX=4301h), which results in incremental backups not backing up the file under its new name open files should not be renamed (DOS 3.0+) allows renaming of directories (DOS 3.1+) wildcards are allowed if invoked via AX=5D00h, in which case error 12h (no more files) is returned on success, and both source and destination specs must be canonical (as returned by AH=60h). Wildcards in the destination are replaced by the corresponding char of each source file being renamed. Under DOS 3.x, the call will fail if the destination wildcard is *.* or equivalent; under DR-DOS 5.0, the call will fail if any wildcards are used. When invoked via AX=5D00h, only those files matching the attribute mask in CL are renamed. under the FlashTek X-32 DOS extender, the old-name pointer is in DS:EDX and the new-name pointer is in ES:EDI (DS must equal ES) (DOS 2.x only) this function renames file by creating a new directory entry with the new name,then marking the old entry deleted BUG: under DR-DOS 3.41, this function will generate a new directory entry with the new name (including any wildcards) which can only be removed with a sector editor when invoked via AX=5D00h SeeAlso: AH=17h,AX=4301h,AX=5D00h,AH=60h,AH=71h --------v-215643------------------------ INT 21 - VIRUS - "PS-MPC.Gold" - INSTALLATION CHECK AX = 5643h ('VC') Return: AX = 5053h ('PS') if resident SeeAlso: AX=33E0h"VIRUS",AX=6303h"VIRUS" --------D-215700----------------------------- INT 21 - DOS 2+ - GET FILE'S DATE AND TIME AX = 5700h BX = file handle Return: CF clear if successful CX = file's time (see #0876) DX = file's date (see #0877) CF set on error AX = error code (01h,06h) (see #0885) Note: under DR-DOS 3.41 and 5.0, this function returns 0 (no date/time) for character devices; MS-DOS returns date and time of opening SeeAlso: AX=5701h Bitfields for file time: Bit(s) Description (Table 0876) 15-11 hours (0-23) 10-5 minutes 4-0 seconds/2 Bitfields for file date: Bit(s) Description (Table 0877) 15-9 year - 1980 8-5 month 4-0 day --------D-215701----------------------------- INT 21 - DOS 2+ - SET FILE'S DATE AND TIME AX = 5701h BX = file handle CX = new time (see #0876) DX = new date (see #0877) Return: CF clear if successful CF set on error AX = error code (01h,06h) (see #0885) SeeAlso: AX=5700h --------D-215702----------------------------- INT 21 - DOS 4.x only - GET EXTENDED ATTRIBUTES FOR FILE AX = 5702h BX = file handle CX = size of result buffer or 0000h DS:SI -> EAP list (see #0878) ES:DI -> buffer for returned EAV list (see #0881) Return: CF clear if successful CX = size of returned data CF set on error AX = error code (see #0885) Desc: get the current value of one or more extended attributes Notes: if CX=0000h on entry, ES:DI is ignored and no data is actually returned, only the amount of data which is available the default DOS 4 behavior is to return a single word of 0000h (no structures) in the result buffer if CX>=0002h on entry SeeAlso: AX=5703h,AX=5704h,AH=6Eh,INT 2F/AX=112Dh Format of EAP (extended attribute properties) list: Offset Size Description (Table 0878) 00h WORD number of EAP structures following 02h var array of EAP structures (see #0879) SeeAlso: #0881 Format of EAP (extended attribute property) structure: Offset Size Description (Table 0879) 00h BYTE attribute type 01h boolean (either 00h or 01h) 02h number (BYTE, WORD, or DWORD) 03h string 04h date stamp 05h time stamp 01h WORD EAP flags (see #0880) 03h BYTE size of reference string (name) 04h N BYTEs reference string Bitfields for EAP flags: Bit(s) Description (Table 0880) 12 unchangeable 13 ignore 14 unchangeable 15 used by COMMAND.COM for code page, but not understood by ATTRIB Format of EAV (extended attribute value) list: Offset Size Description (Table 0881) 00h WORD number of EAV structures following 02h var array of Extended Attribute Value structures (see #0882) SeeAlso: #0878 Format of Extended Attribute Value structures: Offset Size Description (Table 0882) 00h 4 BYTEs ??? 04h BYTE size of reference string 05h WORD size of value 07h var reference string var value --------O-215702----------------------------- INT 21 - OS/2 v1.1+ Family API - DosQFileInfo AX = 5702h BX = file handle CX = size of buffer for information DX = level of information ES:DI -> buffer for information Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5702h/BX=FFFFh,AX=5703h"OS/2" --------O-215702BXFFFF----------------------- INT 21 - OS/2 v1.1+ Compatibility Box Family API - DosQPathInfo AX = 5702h BX = FFFFh CX = size of buffer for information DX = level of information (0002h) DS:SI -> filename ES:DI -> buffer for FAPI path information (see #0883) Return: CF clear if successful AL = 00h CF set on error AX = error code SeeAlso: AX=5702h"OS/2",AX=5703h/BX=FFFFh Format of FAPI path information: Offset Size Description (Table 0883) 00h 22 BYTEs ??? 16h DWORD extended attribute size (none present if less than 5) --------D-215703----------------------------- INT 21 - DOS 4.x only - GET EXTENDED ATTRIBUTE PROPERTIES AX = 5703h BX = file handle CX = size of result buffer or 0000h ES:DI -> result buffer Return: CF clear if successful CX = size of returned data CF set on error AX = error code (see #0885) ES:DI -> zero word (DOS 4.0) if CX >= 2 on entry Desc: get a list of the extended attributes which are defined for the specified file Notes: if CX=0000h on entry, ES:DI is ignored and no data is actually returned, only the amount of data which is available the default DOS 4 behavior is to return a trivial EAP list consisting of the single word 0000h (no EAP structures) if CX>=0002h on entry SeeAlso: AX=5702h,AX=5704h,AH=6Eh,INT 2F/AX=112Dh --------O-215703----------------------------- INT 21 - OS/2 v1.1+ Family API - DosSetFileInfo AX = 5703h BX = file handle CX = size of information buffer DX = level of information ES:DI -> information buffer Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5702h"OS/2",AX=5703h/BX=FFFFh --------O-215703BXFFFF----------------------- INT 21 - OS/2 v1.1+ Family API - DosSetPathInfo AX = 5703h BX = FFFFh CX = size of information buffer DX = level of information DS:SI -> filename ES:DI -> information buffer Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5702h/BX=FFFFh,AX=5703h"OS/2" --------D-215704----------------------------- INT 21 - DOS 4.x only - SET EXTENDED ATTRIBUTES AX = 5704h BX = file handle ES:DI -> EAV list (see #0881) Return: CF clear if successful CF set on error AX = error code (see #0885) Note: the default DOS 4 behavior is to do nothing and return successfully SeeAlso: AX=5702h,AX=5703h,INT 2F/AX=112Dh --------U-215757BX5757----------------------- INT 21 U - IBM Genie - Resident Manager - INSTALLATION CHECK AX = 5757h BX = 5757h Return: AX = 0000h if installed BX = ??? DX = ??? DS:SI -> list of 27 DWORD entry point addresses Program: IBM Genie is a set of utility TSRs by Helix Software Note: other functions possible if BX <> 5757h, but details not yet available ----------215758----------------------------- INT 21 U - Headroom - API AX = 5758h BL = function 00h ??? 01h get Headroom location Return: CF clear if installed AX = PSP segment of Headroom TSR BX = paragraphs of memory used by Headroom CF set if not (normal DOS return) Note: this function is also used as an installation check 02h get INT 21 handler Return: CF clear ES:BX -> Headroom's INT 21 handler Note: also sets unknown flag 03h launch application??? DS:SI -> 233-byte application record Return: ??? 04h ??? ??? Return: CF clear 05h get swap directory Return: CF clear DX:AX -> ASCIZ swap directory name 06h ??? DX = ??? Return: CF clear 07h ??? 08h ??? 09h get current application Return: BX = application number 0Ah ??? DX = application number DS:SI = ??? Return: ??? 0Bh ??? 0Ch ??? DX = application number ??? Return: ??? 0Dh ??? DX = application number ??? Return: ??? 0Eh get ??? Return: CF clear AX = ??? 0Fh set ??? flag 10h clear ??? flag 11h find application by name DS:SI -> ASCIZ application name Return: CF clear AX = application number or FFFFh if not loaded 12h ??? DX = application number Return: CF clear ??? 13h ??? Return: CF clear 14h ??? same as function 13h 15h set ??? DX = ??? 16h get ??? Return: AX = ??? set by function 15h 17h get ??? Return: BX = ??? CX = ??? (may be pointer in BX:CX) 18h BUG: branches incorrectly due to fencepost error Program: Headroom is a TSR/task switcher by Helix Software SeeAlso: AX=4C57h,AX=5757h,INT 2F/AX=5758h --------D-2158------------------------------- INT 21 - DOS 2.11+ - GET OR SET MEMORY ALLOCATION STRATEGY AH = 58h AL = subfunction 00h get allocation strategy Return: AX = current strategy (see #0884) 01h set allocation strategy BL = new allocation strategy (see #0884) BH = 00h (DOS 5+) Return: CF clear if successful CF set on error AX = error code (01h) (see #0885) Notes: the Set subfunction accepts any value in BL for DOS 3.x and 4.x; 2 or greater means last fit the Get subfunction returns the last value set setting an allocation strategy involving high memory does not automatically link in the UMB memory chain; this must be done explicitly with AX=5803h in order to actually allocate high memory a program which changes the allocation strategy should restore it before terminating Toshiba MS-DOS v2.11 supports subfunctions 00h and 01h, as does the TI Professional MS-DOS v2.13 DR-DOS 3.41 reportedly reverses subfunctions 00h and 01h SeeAlso: AH=48h,AH=49h,AH=4Ah,INT 2F/AX=4310h,INT 67/AH=3Fh (Table 0884) Values for DOS memory allocation strategy: 00h low memory first fit 01h low memory best fit 02h low memory last fit ---DOS 5+ --- 40h high memory first fit 41h high memory best fit 42h high memory last fit 80h first fit, try high then low memory 81h best fit, try high then low memory 82h last fit, try high then low memory --------D-2158------------------------------- INT 21 - DOS 5+ - GET OR SET UMB LINK STATE AH = 58h AL = subfunction 02h get UMB link state Return: AL = current link state 00h UMBs not part of DOS memory chain 01h UMBs in DOS memory chain 03h set UMB link state BX = new link state 0000h remove UMBs from DOS memory chain 0001h add UMBs to DOS memory chain Return: CF clear if successful CF set on error AX = error code (01h) (see #0885) Notes: a program which changes the UMB link state should restore it before terminating UMBs will only be available if CONFIG.SYS contains the line DOS=UMB, the UMBs have been linked into the memory chain with AX=5803h, and the allocation strategy has been set to include high memory with AX=5801h SeeAlso: #1485 at INT 2F/AX=4310h --------v-2158CC----------------------------- INT 21 - VIRUS - "1067"/"Headcrash" - INSTALLATION CHECK AX = 58CCh Return: CF clear if resident SeeAlso: AX=5643h,AX=5252h,AX=58DDh,AX=6303h"VIRUS",AX=6969h --------v-2158DD----------------------------- INT 21 - VIRUS - "1067"/"Headcrash" - GET ORIGINAL INT 21h VECTOR AX = 58DDh Return: CX = code segment of virus ES:BX = old INT 21h vector SeeAlso: AX=5252h,AX=58CCh,AX=6969h --------D-2159--BX0000----------------------- INT 21 - DOS 3.0+ - GET EXTENDED ERROR INFORMATION AH = 59h BX = 0000h Return: AX = extended error code (see #0885) BH = error class (see #0887) BL = recommended action (see #0888) CH = error locus (see #0889) ES:DI may be pointer (see #0886, error code list below) CL, DX, SI, BP, and DS destroyed Notes: functions available under DOS 2.x map the true DOS 3.0+ error code into one supported under DOS 2.x you should call this function to retrieve the true error code when an FCB or DOS 2.x call returns an error under DR-DOS 5.0, this function does not use any of the DOS-internal stacks and may thus be called at any time SeeAlso: AH=59h/BX=0001h,AX=5D0Ah,INT 2F/AX=122Dh (Table 0885) Values for DOS extended error code: 00h (0) no error 01h (1) function number invalid 02h (2) file not found 03h (3) path not found 04h (4) too many open files (no handles available) 05h (5) access denied 06h (6) invalid handle 07h (7) memory control block destroyed 08h (8) insufficient memory 09h (9) memory block address invalid 0Ah (10) environment invalid (usually >32K in length) 0Bh (11) format invalid 0Ch (12) access code invalid 0Dh (13) data invalid 0Eh (14) reserved 0Fh (15) invalid drive 10h (16) attempted to remove current directory 11h (17) not same device 12h (18) no more files ---DOS 3.0+ --- 13h (19) disk write-protected 14h (20) unknown unit 15h (21) drive not ready 16h (22) unknown command 17h (23) data error (CRC) 18h (24) bad request structure length 19h (25) seek error 1Ah (26) unknown media type (non-DOS disk) 1Bh (27) sector not found 1Ch (28) printer out of paper 1Dh (29) write fault 1Eh (30) read fault 1Fh (31) general failure 20h (32) sharing violation 21h (33) lock violation 22h (34) disk change invalid (ES:DI -> media ID structure)(see #0886) 23h (35) FCB unavailable 24h (36) sharing buffer overflow 25h (37) (DOS 4.0+) code page mismatch 26h (38) (DOS 4.0+) cannot complete file operation (out of input) 27h (39) (DOS 4.0+) insufficient disk space 28h-31h reserved 32h (50) network request not supported 33h (51) remote computer not listening 34h (52) duplicate name on network 35h (53) network name not found 36h (54) network busy 37h (55) network device no longer exists 38h (56) network BIOS command limit exceeded 39h (57) network adapter hardware error 3Ah (58) incorrect response from network 3Bh (59) unexpected network error 3Ch (60) incompatible remote adapter 3Dh (61) print queue full 3Eh (62) queue not full 3Fh (63) not enough space to print file 40h (64) network name was deleted 41h (65) network: Access denied 42h (66) network device type incorrect 43h (67) network name not found 44h (68) network name limit exceeded 45h (69) network BIOS session limit exceeded 46h (70) temporarily paused 47h (71) network request not accepted 48h (72) network print/disk redirection paused 49h (73) network software not installed (LANtastic) invalid network version 4Ah (74) unexpected adapter close (LANtastic) account expired 4Bh (75) (LANtastic) password expired 4Ch (76) (LANtastic) login attempt invalid at this time 4Dh (77) (LANtastic v3+) disk limit exceeded on network node 4Eh (78) (LANtastic v3+) not logged in to network node 4Fh (79) reserved 50h (80) file exists 51h (81) reserved 52h (82) cannot make directory 53h (83) fail on INT 24h 54h (84) (DOS 3.3+) too many redirections 55h (85) (DOS 3.3+) duplicate redirection 56h (86) (DOS 3.3+) invalid password 57h (87) (DOS 3.3+) invalid parameter 58h (88) (DOS 3.3+) network write fault 59h (89) (DOS 4.0+) function not supported on network 5Ah (90) (DOS 4.0+) required system component not installed 64h (100) (MSCDEX) unknown error 65h (101) (MSCDEX) not ready 66h (102) (MSCDEX) EMS memory no longer valid 67h (103) (MSCDEX) not High Sierra or ISO-9660 format 68h (104) (MSCDEX) door open Format of media ID structure: Offset Size Description (Table 0886) 00h 12 BYTEs ASCIZ volume label of required disk 0Ch DWORD serial number (DOS 4.0+) (Table 0887) Values for DOS Error Class: 01h out of resource (storage space or I/O channels) 02h temporary situation (file or record lock) 03h authorization (denied access) 04h internal (system software bug) 05h hardware failure 06h system failure (configuration file missing or incorrect) 07h application program error 08h not found 09h bad format 0Ah locked 0Bh media error 0Ch already exists 0Dh unknown (Table 0888) Values for DOS Suggested Action: 01h retry 02h delayed retry 03h prompt user to reenter input 04h abort after cleanup 05h immediate abort 06h ignore 07h retry after user intervention (Table 0889) Values for DOS Error Locus: 01h unknown or not appropriate 02h block device (disk error) 03h network related 04h serial device (timeout) 05h memory related --------D-2159--BX0001----------------------- INT 21 - European MS-DOS 4.0 - GET HARD ERROR INFORMATION AH = 59h BX = 0001h Return: ES:DI -> hard error information packet (see #0890) for most recent hard (critical) error SeeAlso: AH=59h/BX=0000h,AH=95h,INT 24 Format of European MS-DOS 4.0 hard error information packet: Offset Size Description (Table 0890) 00h WORD contents of AX at system entry 02h WORD Process ID which encountered error 04h WORD contents of AX at time of error 06h BYTE error type 00h physical I/O error 01h disk change request 02h file sharing violation 03h FCB problem 04h file locking violation 05h bad FAT 06h network detected error 07h BYTE INT 24 error code 08h WORD extended error code (see #0885) 0Ah DWORD pointer to associated device --------D-215A------------------------------- INT 21 - DOS 3.0+ - CREATE TEMPORARY FILE AH = 5Ah CX = file attribute (see #0643 at AX=4301h) DS:DX -> ASCIZ path ending with a '\' + 13 zero bytes to receive the generated filename Return: CF clear if successful AX = file handle opened for read/write in compatibility mode DS:DX pathname extended with generated name for temporary file CF set on error AX = error code (03h,04h,05h) (see #0885) Desc: creates a file with a unique name which must be explicitly deleted BUGS: COMPAQ DOS 3.31 hangs if the pathname is at XXXXh:0000h; it apparently wraps around to the end of the segment MS-DOS 5.00 revisions A and B and PC-DOS 5.00 revision A reportedly hang the system if the specified path is the root directory and the root directory is full (no free directory entries) Note: under the FlashTek X-32 DOS extender, the path pointer is in DS:EDX SeeAlso: AH=3Ch,AH=5Bh --------D-215B------------------------------- INT 21 - DOS 3.0+ - CREATE NEW FILE AH = 5Bh CX = file attribute (see #0643 at AX=4301h) DS:DX -> ASCIZ filename Return: CF clear if successful AX = file handle opened for read/write in compatibility mode CF set on error AX = error code (03h,04h,05h,50h) (see #0885) Notes: unlike AH=3Ch, this function will fail if the specified file exists rather than truncating it; this permits its use in creating semaphore files because it is an atomic "test and set" operation under the FlashTek X-32 DOS extender, the filename pointer is in DS:EDX SeeAlso: AH=3Ch,AH=5Ah --------D-215C------------------------------- INT 21 - DOS 3.0+ - "FLOCK" - RECORD LOCKING AH = 5Ch AL = subfunction 00h lock region of file 01h unlock region of file BX = file handle CX:DX = start offset of region within file SI:DI = length of region in bytes Return: CF clear if successful CF set on error AX = error code (01h,06h,21h,24h) (see #0885) Notes: error returned unless SHARE or network installed an unlock call must specify the same region as some prior lock call locked regions become entirely inaccessible to other processes duplicate handles created with AH=45h or AH=46h inherit locks, but handles inherited by child processes (see AH=4Bh) do not under DR-DOS 3.41 and 5.0, if a process opens a file without the no- inherit flag and then starts a child, any locks set by the parent are ignored, and the child will only get an error if it tries to lock an area previously locked by the parent process SeeAlso: AX=440Bh,AH=BCh,AH=BEh,INT 2F/AX=110Ah,INT 2F/AX=110Bh --------D-215D00----------------------------- INT 21 U - DOS 3.1+ internal - SERVER FUNCTION CALL AX = 5D00h DS:DX -> DOS parameter list (see #0891) DPL contains all register values for a call to INT 21h Return: as appropriate for function being called Notes: does not check AH. Out of range values will crash the system executes using specified computer ID and process ID sharing delay loops skipped a special sharing mode is enabled to handle FCBs opened across network wildcards are enabled for DELETE (AH=41h) and RENAME (AH=56h) under MS-DOS; under DR-DOS 3.41, wildcards corrupt the filesystem; and under DR-DOS 5.0-6.0, the call returns error code 03h due to improper support for the server function call (see below) an extra file attribute parameter is enabled for OPEN (AH=3Dh), DELETE (AH=41h), and RENAME (AH=56h) functions which take filenames require canonical names (as returned by AH=60h); this is apparently to prevent multi-hop file forwarding BUGS: the OS/2 2.0 DOS Boot Session incorrectly maps DOS drive letters, seemingly ignoring HPFS drives DR-DOS 5.0-6.0 merely recursively call INT 21 after loading the registers from the DPL, leading to problems for peer-to-peer networks SeeAlso: AH=3Dh,AH=41h,AH=56h,AH=60h Format of DOS parameter list: Offset Size Description (Table 0891) 00h WORD AX 02h WORD BX 04h WORD CX 06h WORD DX 08h WORD SI 0Ah WORD DI 0Ch WORD DS 0Eh WORD ES 10h WORD reserved (0) 12h WORD computer ID (0 = current system) 14h WORD process ID (PSP segment on specified computer) Note: under Windows Enhanced mode, the computer ID is normally the virtual machine ID (see INT 2F/AX=1683h), though this can reportedly be changed by setting UniqueDOSPSP= in SYSTEM.INI --------D-215D01----------------------------- INT 21 U - DOS 3.1+ internal - COMMIT ALL FILES FOR SPECIFIED COMPUTER/PROCESS AX = 5D01h DS:DX -> DOS parameter list (see #0891), only computer ID and process ID fields used Return: CF set on error AX = error code (see #0885) CF clear if successful Notes: flushes buffers and updates directory entries for each file which has been written to; if remote file, calls INT 2F/AX=1107h the computer ID and process ID are stored but ignored under DOS 3.3 not supported by DR-DOS 3.41 and 5.0; returns error code 01h SeeAlso: AH=0Dh,AH=68h,INT 2F/AX=1107h --------D-215D02----------------------------- INT 21 U - DOS 3.1+ internal - SHARE.EXE - CLOSE FILE BY NAME AX = 5D02h DS:DX -> DOS parameter list (see #0891), only fields DX, DS, computer ID, and process ID used DPL's DS:DX -> ASCIZ name of file to close Return: CF set on error AX = error code (see #0885) CF clear if successful Notes: error unless SHARE is loaded (calls [SysFileTable-28h]) (see #0848 at AH=52h) name must be canonical fully-qualified, such as returned by AH=60h not supported by DR-DOS 3.41 and 5.0; returns error code 01h not supported by Novell DOS 7 SeeAlso: AX=5D03h,AX=5D04h,AH=3Eh,AH=60h --------D-215D03----------------------------- INT 21 U - DOS 3.1+ internal - SHARE.EXE - CLOSE ALL FILES FOR GIVEN COMPUTER AX = 5D03h DS:DX -> DOS parameter list (see #0891), only computer ID used Return: CF set on error AX = error code (see #0885) CF clear if successful Notes: error unless SHARE is loaded (calls [SysFileTable-30h]) (see #0848 at AH=52h) not supported by DR-DOS 3.41 and 5.0; returns error code 01h not supported by Novell DOS 7 SeeAlso: AX=5D02h,AX=5D04h --------D-215D04----------------------------- INT 21 U - DOS 3.1+ internal - SHARE.EXE - CLOSE ALL FILES FOR GIVEN PROCESS AX = 5D04h DS:DX -> DOS parameter list (see #0891), only computer ID and process ID fields used Return: CF set on error AX = error code (see #0885) CF clear if successful Notes: error unless SHARE is loaded (calls [SysFileTable-2Ch]) (see #0848 at AH=52h) not supported by DR-DOS 3.41 and 5.0; returns error code 01h not supported by Novell DOS 7 SeeAlso: AX=5D02h,AX=5D03h,INT 2F/AX=111Dh --------D-215D05----------------------------- INT 21 U - DOS 3.1+ internal - SHARE.EXE - GET OPEN FILE LIST ENTRY AX = 5D05h DS:DX -> DOS parameter list (see #0891) DPL's BX = index of sharing record (see #0849 at AH=52h) DPL's CX = index of SFT in sharing record's SFT list Return: CF clear if successful ES:DI -> ASCIZ filename BX = network machine number of SFT's owner CX = number of locks held by SFT's owner CF set if either index out of range AX = 0012h (no more files) Notes: error unless SHARE is loaded (calls [SysFileTable-18h]) (see #0848 at AH=52h) names are always canonical fully-qualified, such as returned by AH=60h not supported by DR-DOS 3.41 and 5.0 and Novell DOS 7, but does not return an error, instead destroying AX SeeAlso: AH=5Ch,AH=60h --------D-215D06----------------------------- INT 21 U - DOS 3.0+ internal - GET ADDRESS OF DOS SWAPPABLE DATA AREA AX = 5D06h Return: CF set on error AX = error code (see #0885) CF clear if successful DS:SI -> nonreentrant data area (includes all three DOS stacks) (critical error flag is first byte) (see #0892) CX = size in bytes of area which must be swapped while in DOS DX = size in bytes of area which must always be swapped Notes: the Critical Error flag is used in conjunction with the InDOS flag (see AH=34h) to determine when it is safe to enter DOS from a TSR setting CritErr flag allows use of functions 50h/51h from INT 28h under DOS 2.x by forcing use of correct stack swapping the data area allows reentering DOS unless DOS is in a critical section delimited by INT 2A/AH=80h and INT 2A/AH=81h,82h under DOS 4.0, AX=5D0Bh should be used instead of this function SHARE and other DOS utilities consult the byte at offset 04h in the DOS data segment (see INT 2F/AX=1203h) to determine the SDA format in use: 00h = DOS 3.x, 01h = DOS 4.0-6.0, other = error. DR-DOS 3.41+ supports this function, but the SDA format beyond the first 18h bytes is completely different from MS-DOS SeeAlso: AX=5D0Bh,INT 2A/AH=80h,INT 2A/AH=81h,INT 2A/AH=82h Format of DOS 3.10-3.30 Swappable Data Area: Offset Size Description (Table 0892) -34 BYTE (DOS 3.10+) printer echo flag (00h off, FFh active) -31 BYTE (DOS 3.30) current switch character -28 BYTE (DOS 3.30) incremented on each INT 21/AX=5E01h call -27 16 BYTEs (DOS 3.30) machine name set by INT 21/AX=5E01h -11 5 WORDs zero-terminated list of offsets which need to be patched to enable critical-section calls (see INT 2A/AH=80h) -1 BYTE unused padding ---start of actual SDA--- 00h BYTE critical error flag ("ErrorMode") 01h BYTE InDOS flag (count of active INT 21 calls) 02h BYTE drive on which current critical error occurred, or FFh (DR-DOS sets to drive number during INT 24, 00h otherwise) 03h BYTE locus of last error 04h WORD extended error code of last error 06h BYTE suggested action for last error 07h BYTE class of last error 08h DWORD ES:DI pointer for last error 0Ch DWORD current DTA (Disk Transfer Address) note: may point into SDA during the DOS EXEC function (see AH=4Bh), so programs which swap the SDA must be prepared to move the DTA to a private buffer if they might be invoked during an EXEC 10h WORD current PSP 12h WORD stores SP across an INT 23 14h WORD return code from last process termination (zerod after reading with AH=4Dh) 16h BYTE current drive 17h BYTE extended break flag ---remainder need only be swapped if in DOS--- 18h WORD value of AX on call to INT 21 1Ah WORD PSP segment for sharing/network 1Ch WORD network machine number for sharing/network (0000h = us) 1Eh WORD first usable memory block found when allocating memory 20h WORD best usable memory block found when allocating memory 22h WORD last usable memory block found when allocating memory 24h WORD memory size in paragraphs (used only during initialization) 26h WORD last entry checked during directory search 28h BYTE flag: INT 24 returned Fail 29h BYTE flags: allowable INT 24 actions (passed to INT 24 in AH) 2Ah BYTE directory flag (00h directory, 01h file) 2Bh BYTE flag: FFh if Ctrl-Break termination, 00h otherwise 2Ch BYTE flag: allow embedded blanks in FCB 2Dh BYTE padding (unused) 2Eh BYTE day of month 2Fh BYTE month 30h WORD year - 1980 32h WORD number of days since 1-1-1980 34h BYTE day of week (0 = Sunday) 35h BYTE flag: console swapped during read from device 36h BYTE flag: safe to call INT 28 if nonzero 37h BYTE flag: if nonzero, INT 24 Abort turned into INT 24 Fail (set only during process termination) 38h 26 BYTEs device driver request header (see #1382 at INT 2F/AX=0802h) 52h DWORD pointer to device driver entry point (used in calling driver) 56h 22 BYTEs device driver request header for I/O calls 6Ch 14 BYTEs device driver request header for disk status check 7Ah DWORD pointer to device I/O buffer??? 7Eh WORD ??? 80h WORD ??? 82h BYTE type of PSP copy (00h=simple for INT 21/AH=26h, FFh=make child) 83h BYTE padding (unused) 84h 3 BYTEs 24-bit user number (see AH=30h) 87h BYTE OEM number (see #0619 at AH=30h) 88h WORD offset to error code conversion table for INT 25/INT 26 8Ah 6 BYTEs CLOCK$ transfer record (see #0893) 90h BYTE device I/O buffer for single-byte I/O functions 91h BYTE padding??? (unused) 92h 128 BYTEs buffer for filename 112h 128 BYTEs buffer for filename 192h 21 BYTEs findfirst/findnext search data block (see #0839 at AH=4Eh) 1A7h 32 BYTEs directory entry for found file (see #0580 at AH=11h) 1C7h 81 BYTEs copy of current directory structure for drive being accessed 218h 11 BYTEs FCB-format filename for device name comparison 223h BYTE terminating NUL for above filename 224h 11 BYTEs wildcard destination specification for rename (FCB format) 22Fh BYTE terminating NUL for above spec 230h BYTE ??? 231h WORD destination file/directory starting sector 233h 5 BYTEs ??? 238h BYTE extended FCB file attribute 239h BYTE type of FCB (00h regular, FFh extended) 23Ah BYTE directory search attributes 23Bh BYTE file open/access mode 23Ch BYTE file found/delete flag bit 0: file found bit 4: file deleted 23Dh BYTE flag: device name found on rename, or file not found 23Eh BYTE splice flag (file name and directory name together) 23Fh BYTE flag indicating how DOS function was invoked (00h = direct INT 20/INT 21, FFh = server call AX=5D00h) 240h BYTE sector position within cluster 241h BYTE flag: translate sector/cluster (00h no, 01h yes) 242h BYTE flag: 00h if read, 01h if write 243h BYTE current working drive number 244h BYTE cluster factor 245h BYTE flag: cluster split mode 246h BYTE line edit (AH=0Ah) insert mode flag (nonzero = on) 247h BYTE canonicalized filename referred to existing file/dir if FFh 248h BYTE volume ID flag 249h BYTE type of process termination (00h-03h) (see AH=4Dh) 24Ah BYTE file create flag (00h = no, search only) 24Bh BYTE value with which to replace first byte of deleted file's name (normally E5h, but 00h as described under INT 21/AH=13h) 24Ch DWORD pointer to Drive Parameter Block for critical error invocation temp: used during process termination 250h DWORD pointer to stack frame containing user registers on INT 21 254h WORD stores SP across INT 24 256h DWORD pointer to DOS Drive Parameter Block for ??? 25Ah WORD saving partial cluster number 25Ch WORD temp: sector of work current cluster 25Eh WORD high part of cluster number (only low byte referenced) 260h WORD ??? temp 262h BYTE Media ID byte returned by AH=1Bh,1Ch 263h BYTE padding (unused) 264h DWORD pointer to device header when filename is character device 268h DWORD pointer to current SFT 26Ch DWORD pointer to current directory structure for drive being accessed 270h DWORD pointer to caller's FCB 274h WORD number of SFT to which file being opened will refer 276h WORD temporary storage for file handle 278h DWORD pointer to a JFT entry in process handle table (see #0603 at AH=26h) 27Ch WORD offset in DOS DS of first filename argument 27Eh WORD offset in DOS DS of second filename argument 280h WORD offset of last component in pathname or FFFFh 282h WORD offset of transfer address to add 284h WORD last relative cluster within file being accessed 286h WORD temp: absolute cluster number being accessed 288h WORD directory sector number 28Ah WORD ??? current cluster number 28Ch WORD current relative sector number within file 28Eh WORD current sector number 290h WORD current byte offset within sector 292h DWORD current offset in file 296h DWORD temp: file byte count 29Ah WORD temp: file byte count 29Ch WORD free file cluster entry 29Eh WORD last file cluster entry 2A0h WORD next file cluster number 2A2h DWORD number of bytes appended to file 2A6h DWORD pointer to current work disk buffer 2AAh DWORD pointer to working SFT 2AEh WORD used by INT 21 dispatcher to store caller's BX 2B0h WORD used by INT 21 dispatcher to store caller's DS 2B2h WORD temporary storage while saving/restoring caller's registers 2B4h DWORD pointer to prev call frame (offset 250h) if INT 21 reentered also switched to for duration of INT 24 2B8h 21 BYTEs FindFirst search data for source file(s) of a rename operation (see #0839 at AH=4Eh) 2CDh 32 BYTEs directory entry for file being renamed (see #0580 at AH=11h) 2EDh 331 BYTEs critical error stack 403h 35 BYTEs scratch SFT 438h 384 BYTEs disk stack (functions greater than 0Ch, INT 25,INT 26) 5B8h 384 BYTEs character I/O stack (functions 01h through 0Ch) ---DOS 3.2,3.3x only--- 738h BYTE device driver lookahead flag (usually printer) (see AH=64h) 739h BYTE volume change flag 73Ah BYTE flag: virtual open 73Bh BYTE ??? SeeAlso: #0895 Format of CLOCK$ transfer record: Offset Size Description (Table 0893) 00h WORD number of days since 1-Jan-1980 02h BYTE minutes 03h BYTE hours 04h BYTE hundredths of second 05h BYTE seconds --------D-215D07----------------------------- INT 21 U - DOS 3.1+ network - GET REDIRECTED PRINTER MODE AX = 5D07h Return: DL = mode 00h redirected output is combined 01h redirected output in separate print jobs SeeAlso: AX=5D08h,AX=5D09h,INT 2F/AX=1125h --------D-215D08----------------------------- INT 21 U - DOS 3.1+ network - SET REDIRECTED PRINTER MODE AX = 5D08h DL = mode 00h redirected output is combined 01h redirected output placed in separate jobs, start new print job now SeeAlso: AX=5D07h,AX=5D09h,INT 2F/AX=1125h --------D-215D09----------------------------- INT 21 U - DOS 3.1+ network - FLUSH REDIRECTED PRINTER OUTPUT AX = 5D09h Notes: forces redirected printer output to be printed, and starts a new print job this function is also supported by 10Net, which calls it Terminate All Spool Jobs, and does not flush if in "combine" mode SeeAlso: AX=5D07h,AX=5D08h,INT 2F/AX=1125h --------D-215D0A----------------------------- INT 21 - DOS 3.1+ - SET EXTENDED ERROR INFORMATION AX = 5D0Ah DS:DX -> 11-word DOS parameter list (see #0891) Return: nothing. next call to AH=59h will return values from fields AX,BX,CX, DX,DI, and ES in corresponding registers Notes: documented for DOS 5+, but undocumented in earlier versions the MS-DOS Programmer's Reference incorrectly states that this call was introduced in DOS 4, and fails to mention that the ERROR structure passed to this function is a DOS parameter list. BUGS: DR-DOS 3.41 and 5.0 read the value for ES from the DS field of the DPL; fortunately, MS-DOS ignores the DS field, allowing a generic routine which sets both DS and ES fields to the same value Novell DOS 7 does not save the pointer, which is always reported as 0000h:0000h by AH=59h SeeAlso: AH=59h/BX=0000h --------D-215D0B----------------------------- INT 21 OU - DOS 4.x only internal - GET DOS SWAPPABLE DATA AREAS AX = 5D0Bh Return: CF set on error AX = error code (see #0885) CF clear if successful DS:SI -> swappable data area list (see #0894) Notes: copying and restoring the swappable data areas allows DOS to be reentered unless it is in a critical section delimited by calls to INT 2A/AH=80h and INT 2A/AH=81h,82h SHARE and other DOS utilities consult the byte at offset 04h in the DOS data segment (see INT 2F/AX=1203h) to determine the SDA format in use: 00h = DOS 3.x, 01h = DOS 4.0-6.0, other = error. DOS 5+ use the SDA format listed below, but revert back to the DOS 3.x call for finding the SDA (see #0892) SeeAlso: AX=5D06h,INT 2A/AH=80h,INT 2A/AH=81h,INT 2A/AH=82h,INT 2F/AX=1203h Format of DOS 4.x swappable data area list: Offset Size Description (Table 0894) 00h WORD count of data areas 02h N BYTEs "count" copies of data area record Offset Size Description 00h DWORD address 04h WORD length and type bit 15 set if swap always, clear if swap in DOS bits 14-0: length in bytes SeeAlso: #0895 Format of DOS 4.0-6.0 swappable data area: Offset Size Description (Table 0895) -34 BYTE printer echo flag (00h off, FFh active) -31 BYTE current switch character (ignored by DOS 5+) -28 BYTE incremented on each INT 21/AX=5E01h call -27 16 BYTEs machine name set by INT 21/AX=5E01h -11 5 WORDs zero-terminated list of offsets which need to be patched to enable critical-section calls (see INT 2A/AH=80h) (all offsets are 0D0Ch, but this list is still present for DOS 3.x compatibility) -1 BYTE unused padding ---start of actual SDA--- 00h BYTE critical error flag ("ErrorMode") 01h BYTE InDOS flag (count of active INT 21 calls) 02h BYTE drive on which current critical error occurred or FFh 03h BYTE locus of last error 04h WORD extended error code of last error 06h BYTE suggested action for last error 07h BYTE class of last error 08h DWORD ES:DI pointer for last error 0Ch DWORD current DTA (Disk Transfer Address) note: may point into SDA during the DOS EXEC function (see AH=4Bh), so programs which swap the SDA must be prepared to move the DTA to a private buffer if they might be invoked during an EXEC 10h WORD current PSP 12h WORD stores SP across an INT 23 14h WORD return code from last process termination (zerod after reading with AH=4Dh) 16h BYTE current drive 17h BYTE extended break flag 18h BYTE flag: code page switching 19h BYTE flag: copy of previous byte in case of INT 24 Abort ---remainder need only be swapped if in DOS--- 1Ah WORD value of AX on call to INT 21 1Ch WORD PSP segment for sharing/network 1Eh WORD network machine number for sharing/network (0000h = us) 20h WORD first usable memory block found when allocating memory 22h WORD best usable memory block found when allocating memory 24h WORD last usable memory block found when allocating memory 26h WORD memory size in paragraphs (used only during initialization) 28h WORD last entry checked during directory search 2Ah BYTE flag: nonzero if INT 24 Fail 2Bh BYTE flags: allowable INT 24 responses (passed to INT 24 in AH) 2Ch BYTE flag: do not set directory if nonzero 2Dh BYTE flag: program aborted by ^C 2Eh BYTE flag: allow embedded blanks in FCB may also allow use of "*" wildcard in FCBs 2Fh BYTE padding (unused) 30h BYTE day of month 31h BYTE month 32h WORD year - 1980 34h WORD number of days since 1-1-1980 36h BYTE day of week (0 = Sunday) 37h BYTE flag: console swapped during read from device 38h BYTE flag: safe to call INT 28 if nonzero 39h BYTE flag: abort currently in progress, turn INT 24 Abort into Fail 3Ah 30 BYTEs device driver request header (see #1382 at INT 2F/AX=0802h) for device calls 58h DWORD pointer to device driver entry point (used in calling driver) 5Ch 22 BYTEs device driver request header for I/O calls 72h 14 BYTEs device driver request header for disk status check 80h DWORD pointer to device I/O buffer 84h WORD ??? 86h WORD ??? (0) 88h BYTE type of PSP copy (00h=simple for INT 21/AH=26h, FFh=make child) 89h DWORD start offset of file region to lock/unlock 8Dh DWORD length of file region to lock/unlock 91h BYTE padding (unused) 92h 3 BYTEs 24-bit user number (see AH=30h) 95h BYTE OEM number (see #0619 at AH=30h) 96h 6 BYTEs CLOCK$ transfer record (see #0893 at AX=5D06h) 9Ch BYTE device I/O buffer for single-byte I/O functions 9Dh BYTE padding??? 9Eh 128 BYTEs buffer for filename 11Eh 128 BYTEs buffer for filename 19Eh 21 BYTEs findfirst/findnext search data block (see #0839 at AH=4Eh) 1B3h 32 BYTEs directory entry for found file (see #0619 at AH=11h) 1D3h 88 BYTEs copy of current directory structure for drive being accessed 22Bh 11 BYTEs FCB-format filename for device name comparison 236h BYTE terminating NUL for above filename 237h 11 BYTEs wildcard destination specification for rename (FCB format) 242h BYTE terminating NUL for above filespec 243h BYTE ??? 244h WORD ??? 246h 5 BYTEs ??? 24Bh BYTE extended FCB file attributes 24Ch BYTE type of FCB (00h regular, FFh extended) 24Dh BYTE directory search attributes 24Eh BYTE file open/access mode 24Fh BYTE ??? flag bits reportedly 00h when deleting a file under MSDOS 5.0 250h BYTE flag: device name found on rename, or file not found 251h BYTE splice flag??? (file name and directory name together) 252h BYTE flag indicating how DOS function was invoked (00h = direct INT 20/INT 21, FFh = server call AX=5D00h) 253h BYTE sector position within cluster 254h BYTE ??? (flag: translate sector/cluster) 255h BYTE ??? (flag: 00h if read, 01h if write) 256h BYTE current working drive number 257h BYTE cluster factor 258h BYTE ??? 259h BYTE line edit (AH=0Ah) insert mode flag (nonzero = on) 25Ah BYTE canonicalized filename referred to existing file/dir if FFh 25Bh BYTE volume ID flag 25Ch BYTE type of process termination (00h-03h) (see AH=4Dh) 25Dh BYTE ??? 25Eh BYTE ??? file create flag (00h = no, search only) 25Fh BYTE ??? (value for deleted file's first byte) 260h DWORD pointer to Drive Parameter Block for critical error invocation 264h DWORD pointer to stack frame containing user registers on INT 21 268h WORD stores SP across INT 24 26Ah DWORD pointer to DOS Drive Parameter Block for ??? 26Eh WORD segment of disk buffer 270h WORD ??? (saving partial cluster number) 272h WORD ??? (temp: sector of work current cluster) 274h WORD ??? (high part of cluster number) 276h WORD ??? (temp) 278h BYTE Media ID byte returned by AH=1Bh,1Ch 279h BYTE ??? (doesn't seem to be referenced) 27Ah DWORD pointer to device header if filename is character device 27Eh DWORD pointer to current SFT 282h DWORD pointer to current directory structure for drive being accessed 286h DWORD pointer to caller's FCB 28Ah WORD SFT index to which file being opened will refer 28Ch WORD temporary storage for file handle 28Eh DWORD pointer to a JFT entry in process handle table (see #0603 at AH=26h) 292h WORD offset in DOS DS of first filename argument 294h WORD offset in DOS DS of second filename argument 296h WORD ??? (offset of last component in pathname or FFFFh) 298h WORD offset of transfer address to add 29Ah WORD last relative cluster within file being accessed 29Ch WORD temp: absolute cluster number being accessed 29Eh WORD directory sector number 2A0h WORD ??? 2A2h WORD ??? directory cluster number 2A4h DWORD current relative sector number within file 2A8h DWORD ??? (current sector number) 2ACh WORD ??? (current byte offset within sector) 2AEh DWORD current offset in file 2B2h WORD ??? 2B4h WORD bytes in partial sector 2B6h WORD number of sectors 2B8h WORD ??? (free file cluster entry) 2BAh WORD ??? (last file cluster entry) 2BCh WORD ??? (next file cluster number) 2BEh DWORD number of bytes appended to file 2C2h DWORD pointer to current work disk buffer 2C6h DWORD pointer to working SFT 2CAh WORD used by INT 21 dispatcher to store caller's BX 2CCh WORD used by INT 21 dispatcher to store caller's DS 2CEh WORD temporary storage while saving/restoring caller's registers 2D0h DWORD pointer to prev call frame (offset 264h) if INT 21 reentered also switched to for duration of INT 24 2D4h WORD open mode/action for INT 21/AX=6C00h 2D6h BYTE ??? (set to 00h by INT 21h dispatcher, 02h when a read is performed, and 01h or 03h by INT 21/AX=6C00h) 2D7h WORD ??? apparently unused 2D9h DWORD stored ES:DI for AX=6C00h 2DDh WORD extended file open action code (see #0966 at AX=6C00h) 2DFh WORD extended file open attributes (see #0965 at AX=6C00h) 2E1h WORD extended file open file mode (see AX=6C00h) 2E3h DWORD pointer to filename to open (see AX=6C00h) 2E7h WORD ??? temp DX storage or 0000h or temp data buffer size from disk buffer 2E9h WORD ??? 2EBh BYTE ??? 2ECh WORD stores DS during call to [List-of-Lists + 37h] 2EEh WORD ??? 2F0h BYTE ??? 2F1h WORD ??? bit flags 2F3h DWORD pointer to user-supplied filename 2F7h DWORD pointer to ??? 2FBh WORD stores SS during call to [List-of-Lists + 37h] 2FDh WORD stores SP during call to [List-of-Lists + 37h] 2FFh BYTE flag, nonzero if stack switched in calling [List-of-Lists+37h] 300h 21 BYTEs FindFirst search data for source file(s) of a rename operation (see #0839 at AH=4Eh) 315h 32 BYTEs directory entry for file being renamed (see #0580 at AH=11h) 335h 331 BYTEs critical error stack 480h 384 BYTEs disk stack (functions greater than 0Ch, INT 25,INT 26) 600h 384 BYTEs character I/O stack (functions 01h through 0Ch) 780h BYTE device driver lookahead flag (usually printer) (see AH=64h) 781h BYTE volume change flag 782h BYTE flag: virtual open 783h BYTE ??? 784h WORD ??? 786h WORD ??? 788h WORD ??? 78Ah WORD ??? SeeAlso: #0892,#0894 --------D-215E00----------------------------- INT 21 - DOS 3.1+ network - GET MACHINE NAME AX = 5E00h DS:DX -> 16-byte buffer for ASCII machine name Return: CF clear if successful CH = validity 00h name invalid nonzero valid CL = NetBIOS number for machine name DS:DX buffer filled with blank-paded name CF set on error AX = error code (01h) (see #0885 at AH=59h) Note: supported by OS/2 v1.3+ compatibility box, PC-NFS SeeAlso: AX=5E01h --------N-215E00----------------------------- INT 21 - 10NET v5.0 - GET MACHINE NAME AX = 5E00h Return: CL = redirector's NetBIOS name number ES:DI -> network node ID SeeAlso: AX=5E01h"10NET" --------D-215E01CH00------------------------- INT 21 - DOS 3.1+ network - SET MACHINE NAME AX = 5E01h CH = 00h undefine name (make it invalid) <> 0 define name CL = name number DS:DX -> 15-character blank-padded ASCIZ name SeeAlso: AX=5E00h --------N-215E01----------------------------- INT 21 - 10NET v5.0 - GET LOCAL 10NET CONFIGURATION TABLE AX = 5E01h CX = length of buffer DS:DX -> buffer for 10Net configuration table (see #821) SeeAlso: AX=5E00h"10NET",INT 6F/AH=02h,INT 6F/AH=03h Format of 10Net Configuration Table: Offset Size Description (Table 0896) 00h 8 BYTEs user name 08h 15 BYTEs node ID 17h 3 BYTEs unique portion of Ethernet address 1Ah BYTE Who group number 1Bh WORD services mask (see #0898) 1Dh DWORD serial number 21h BYTE maximum concurrent users with same serial number allowed on net 22h BYTE chat mask (see #0899) 23h BYTE internal system bits (see #0900) 24h 9 BYTEs version number in format MM.mm.xxx 2Dh BYTE flag: 01h if machine is a PS/2 2Eh BYTE flag: 03h if 80386 2Fh BYTE spool termination mode: 01h concatenate, 02h truncate (see AX=5D09h) 30h WORD autospool timeout in clock ticks 32h WORD monitor timeout in clock ticks 34h WORD unused 36h WORD chat timeout in clock ticks 38h WORD netBIOS session timeout in half-seconds 3Ah WORD datagram send timeout in seconds 3Ch WORD keyboard value for initiating chat mode 3Eh WORD Who timeout in clock ticks 40h BYTE flag: 01h if server should process rom NetBIOS Post return 41h BYTE flag: 01h if FCBs should be recycled 42h 3 BYTEs signature "DBG" 45h BYTE last interrupt (21h or 6Fh) 46h BYTE last INT 21 AH value 47h BYTE last INT 6F AH value 48h WORD last item posted 4Ah WORD last item free-posted 4Ch WORD last item handled by server 4Eh WORD last redirector send NCB 50h WORD last redirector receive NCB 52h 4 BYTEs signature "TABL" 56h WORD offset of datagram buffer table header (see #0897) 58h WORD offset of chat buffer table header (see #0897) 5Ah WORD offset of Raw buffer table header (see #0897) 5Ch WORD offset of Workstation buffer table header (see #0897) 5Eh WORD offset of server receive-any table header (see #0897) 60h WORD offset of Tiny buffer table header (see #0897) 62h WORD offset of zero-length buffer table (NCBs) (see #0897) 64h WORD offset of Rdr (Redirector Mount) table header (see #0897) 66h WORD offset of Ntab (Redirector Session) table header (see #0897) 68h WORD offset of FCB table header (see #0897) 6Ah WORD offset of user file handle table header (see #0897) 6Ch WORD offset of workstation printer RDR extension table header 6Eh WORD offset of server shared device table header (see #0897) 70h WORD offset of server connection table header (see #0897) 72h WORD offset of server login table header (see #0897) 74h WORD offset of server file table header (see #0897) 76h WORD offset of server shared file table header (see #0897) 78h WORD offset of server record lock table header (see #0897) 7Ah WORD offset of remote printer claim table header (see #0897) 7Ch WORD offset of remote printer device table header (see #0897) 7Eh WORD offset of print server mount table header (see #0897) 80h WORD offset of print server sessions table header (see #0897) 82h WORD offset of print server print job structure table header 84h WORD offset of print server pooled device table header (see #0897) 86h WORD size of workstation buffer 88h WORD size of server receive-any buffer 8Ah WORD size of server raw I/O buffer 8Ch 6 BYTEs reserved 92h DWORD pointer to profile pathname 96h BYTE datagram retry count 97h BYTE NetBIOS LAN adapter number 98h 6 BYTEs physical Ethernet address 9Eh BYTE NetBIOS server name number 9Fh BYTE NetBIOS redirector name number A0h BYTE 10Net interrupt number A1h BYTE flag: chat is loaded A2h BYTE flag: INT 6F APIs permanently loaded A3h BYTE flag: file security present A4h WORD reserved A6h BYTE fixed mount bitmask for drives A:-H: A7h BYTE reserved A8h WORD 10Net system flags (see #0901) AAh BYTE monitor flags (see #0902) ABh 5 BYTEs reserved B0h WORD offset of monitor timer block B2h WORD offset of server timer block B4h WORD offset of chat timer block B6h WORD timer chain B8h 4 BYTEs signature "TALS" BCh WORD number of 10Net sends BEh WORD number of 10Net receives C0h WORD number of no-buffer conditions C2h WORD number of dropped posted messages C4h WORD number of server NCB errors C6h WORD number of redirector NCB errors C8h WORD number of datagram send/receive errors CAh WORD number of dropped Whos CCh WORD number of dropped submits CEh WORD number of session aborts D0h BYTE number of NetBIOS interface-busy errors D1h BYTE last NetBIOS bad post command D2h BYTE last NetBIOS bad redirector command D3h BYTE do send datagram send/receive error command D4h DWORD -> DOS system parameter table D8h WORD number of DOS physical drives DAh WORD offset of DOS PSP field in DOS data segment DCh WORD offset of in-DOS flag in DOS data segment DEh WORD DOS data segment E0h WORD offset of DOS SFT in DOS data segment E2h WORD offset of number-of-physical-units field in DOS data segment E4h WORD 10Net code segment E6h WORD 10Net data segment E8h WORD 10Net common server segment EAh WORD 10Net file server segment ECh WORD 10Net print server segment EEh WORD 10Net remote printer segment Note: documentation lists field at offset D0h as a WORD, but all following offsets are as though it were a BYTE; if it is indeed a WORD, all offsets after D0h must be increased by one byte Format of 10Net Table Header: Offset Size Description (Table 0897) -16 4 BYTEs table identifier -12 WORD peak number of tables allocated -10 WORD number of tables currently in use -8 WORD total number of tables -6 WORD size of each table -4 WORD offset of first allocated table -2 WORD offset of first free table Bitfields for 10NET services mask: Bit(s) Description (Table 0898) 0 workstation 1 file server 2 print queue server 3 de-spool server Bitfields for 10NET chat mask: Bit(s) Description (Table 0899) 0 chat permitted 1 bell enabled 2 chat keyboard initiated 3 in INT 16 handler 4 in Get Input 5 display has timed out 6 chat is idle Bitfields for 10NET internal system bits: Bit(s) Description (Table 0900) 0 submit permitted 1 submit initiated 2 submit executing 3 internal client call/chat/spool/autospool 4 in spool termination 5 print permitted 6 waiting for keyboard input Bitfields for 10NET System Flags: Bit(s) Description (Table 0901) 0 in NetBIOS 1 processing INT 28 2 is server 3 in net user-DOS function 4 in DOS user-DOS function 5 in net for user non-DOS function 6 in server DOS function 7 in server non-DOS function 8 in terminate 10 in user on server request 13 in DOS for user on server 14 disable critical error handler Bitfields for Monitor Flags: Bit(s) Description (Table 0902) 0 waiting for monitor response 4 in monitor get-input routine 5 monitor display timeout 6 sensing for escape key --------D-215E02----------------------------- INT 21 - DOS 3.1+ network - SET NETWORK PRINTER SETUP STRING AX = 5E02h BX = redirection list index (see AX=5F02h) CX = length of setup string DS:SI -> setup string Return: CF clear if successful CF set on error AX = error code (01h) (see #0885 at AH=59h) Note: also supported by 10NET v5.0 SeeAlso: AX=5E03h,INT 2F/AX=111Fh --------D-215E03----------------------------- INT 21 - DOS 3.1+ network - GET NETWORK PRINTER SETUP STRING AX = 5E03h BX = redirection list index (see AX=5F02h) ES:DI -> 64-byte buffer for setup string Return: CF clear if successful CX = length of setup string ES:DI buffer filled CF set on error AX = error code (01h) (see #0885 at AH=59h) Note: also supported by 10NET v5.0, but 10NET is documented as using DS:SI instead of ES:DI SeeAlso: AX=5E02h,INT 2F/AX=111Fh --------D-215E04----------------------------- INT 21 - DOS 3.1+ network - SET PRINTER MODE AX = 5E04h BX = redirection list index (see AX=5F02h) DX = mode bit 0: set if binary, clear if text (tabs expanded to blanks) Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful Note: calls INT 2F/AX=111Fh with 5E04h on stack SeeAlso: AX=5E05h"DOS",INT 2F/AX=111Fh --------N-215E04----------------------------- INT 21 - 10NET v5.0 - INITIATE PRINT JOB AX = 5E04h BX = zero-based redirection list index (see AX=5F02h) DS:DX -> extended workstation printer setup structure (see #0903) Return: CF clear if successful CF set on error AX = error code (see #0885 at AH=59h) SeeAlso: AX=5E05h"10NET",AX=5E06h"10NET" Format of 10NET extended workstation printer setup structure: Offset Size Description (Table 0903) 00h BYTE notification flags (see #0904) 01h BYTE job control mask (see #0905) 02h WORD days to retain file 04h WORD test print length 06h BYTE number of copies to print 07h BYTE compression algorithm 08h BYTE tab width (00h = don't expand) 09h BYTE initiation type (00h normal, 01h non-spooled) 0Ah 38 BYTEs job start operation notification instructions 30h 32 BYTEs comment for job 50h 64 BYTEs output filename or non-spooled file Bitfields for 10NET notification flags: Bit(s) Description (Table 0904) 0 user at print start 1 operator at start, with reply 2 user at print completion 3 operator at completion, with reply 4 user on queue switch 5 operator on queue switch, with reply 6 user on print error Bitfields for 10NET job control mask: Bit(s) Description (Table 0905) 0 print banner page 1 eject page at end of job 2 mark as "held" (queue but don't print) 3 rush job (queue at top) 4 overwrite file with zeros before deletion 5 hyperspool if possible --------D-215E05----------------------------- INT 21 - DOS 3.1+ network - GET PRINTER MODE AX = 5E05h BX = redirection list index (see AX=5F02h) Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful DX = printer mode (see AX=5E04h) Note: calls INT 2F/AX=111Fh with 5E05h on stack SeeAlso: AX=5E04h"DOS",INT 2F/AX=111Fh --------N-215E05----------------------------- INT 21 - 10NET v5.0 - TERMINATE PRINT JOB AX = 5E05h BX = zero-based redirection list index (see AX=5F02h) Return: CF clear if successful CF set on error AX = error code (see #0885 at AH=59h) Note: this call resets the spool termination mode to "truncate" (see AX=5D08h) SeeAlso: AX=5E04h"10NET",AX=5E06h --------N-215E06----------------------------- INT 21 - 10NET v5.0 - GET/SET 10NET WORKSTATION PRINTER SETUP STRUCTURE AX = 5E06h BX = zero-based redirection list index (see AX=5F02h) CX = operation (06h set, 07h get) DS:DX -> buffer for setup structure (same as first nine bytes of workstation printer setup) (see #0903) Return: CF clear if successful DS:DX buffer updated on get CF set on error AX = error code (see #0885 at AH=59h) SeeAlso: AX=5E04h"10NET",AX=5E05h"10NET" --------D-215F00----------------------------- INT 21 - DOS 3.1+ network - GET REDIRECTION MODE AX = 5F00h BL = redirection type 03h printer 04h disk drive Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful BH = redirection state 00h off 01h on Note: calls INT 2F/AX=111Eh with AX on top of the stack SeeAlso: AX=5F01h,INT 2F/AX=111Eh --------D-215F01----------------------------- INT 21 - DOS 3.1+ network - SET REDIRECTION MODE AX = 5F01h BL = redirection type 03h printer 04h disk drive BH = redirection state 00h off 01h on Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful Notes: when redirection is off, the local device (if any) rather than the remote device is used calls INT 2F/AX=111Eh with AX on top of the stack SeeAlso: AX=5F00h,INT 2F/AX=111Eh,INT 60/AX=0002h --------D-215F02----------------------------- INT 21 - DOS 3.1+ network - GET REDIRECTION LIST ENTRY AX = 5F02h BX = zero-based redirection list index CX = 0000h (LANtastic) DS:SI -> 16-byte buffer for ASCIZ local device name or drive letter followed by colon ES:DI -> 128-byte buffer for ASCIZ network name Return: CF clear if successful BH = device status 00h valid 01h invalid 02h valid (connected from inside Windows for Workgroups v3.11) BL = device type 03h printer 04h disk drive CX = user data previously set with AX=5F03h DS:SI and ES:DI buffers filled DX,BP destroyed CF set on error AX = error code (01h,12h) (see #0885 at AH=59h) Notes: this function is passed through to INT 2F/AX=111Eh by the DOS kernel error code 12h is returned if BX is greater than the size of the list also supported by Banyan VINES, PC-NFS, LANtastic, and 10NET supported by LapLink RemoteAccess but returns the local drive letter; the remote drive letter can be obtained with INT 2F/AX=Cxxxh (see INT 2F/AX=C000h"LapLink") the returned device name may or may not include a colon, depending on the network software SeeAlso: AX=5F03h,AX=5F46h,INT 2F/AX=111Eh,INT 2F/AX=C000h"LapLink" --------D-215F03----------------------------- INT 21 - DOS 3.1+ network - REDIRECT DEVICE AX = 5F03h BL = device type 03h printer 04h disk drive CX = user data to save 0000h for LANtastic 4E57h ("NW") for NetWare 4.0 requester DS:SI -> ASCIZ local device name (16 bytes max) ES:DI -> ASCIZ network name + ASCIZ password (128 bytes max total) Return: CF clear if successful CF set on error AX = error code (01h,03h,05h,08h,0Fh,12h) (see #0885 at AH=59h) Notes: if device type is disk drive, DS:SI must point at either a null string or a string consisting the drive letter followed by a colon; if a null string, the network attempts to access the destination without redirecting a local drive the DOS kernel calls INT 2F/AX=111Eh with AX on top of the stack also supported by Banyan VINES, LANtastic, and 10NET SeeAlso: AX=5F02h,AX=5F04h,INT 2F/AX=111Eh,INT 60/AX=0002h --------D-215F04----------------------------- INT 21 - DOS 3.1+ network - CANCEL REDIRECTION AX = 5F04h DS:SI -> ASCIZ local device name or path CX = 4E57h ("NW") for NetWare 4.0 requester Return: CF clear if successful CF set on error AX = error code (01h,03h,05h,08h,0Fh,12h) (see #0885 at AH=59h) Notes: the DS:SI string must be either a local device name, a drive letter followed by a colon, or a network directory beginning with two backslashes the DOS kernel calls INT 2F/AX=111Eh with AX on top of the stack also supported by Banyan VINES, LANtastic, and 10NET SeeAlso: AX=5F03h,INT 2F/AX=111Eh,INT 60/AX=0003h --------D-215F05----------------------------- INT 21 - DOS 4.0+ network - GET EXTENDED REDIRECTION LIST ENTRY AX = 5F05h BX = redirection list index DS:SI -> buffer for ASCIZ source device name ES:DI -> buffer for destination ASCIZ network path Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful AX = server's network process ID handle (10NET) BH = device status flag (bit 0 clear if valid) BL = device type (03h if printer, 04h if drive) CX = stored parameter value (user data) from AX=5F03h BP = NETBIOS local session number DS:SI buffer filled ES:DI buffer filled Notes: the local session number allows sharing the redirector's session number if an error is caused on the NETBIOS LSN, the redirector may be unable to correctly recover from errors the DOS kernel calls INT 2F/AX=111Eh with AX on top of the stack supported by DR-DOS 5.0 also supported by 10NET v5.0 SeeAlso: AX=5F06h"Network",INT 2F/AX=111Eh --------O-215F05----------------------------- INT 21 - STARLITE architecture - MAP LOCAL DRIVE LETTER TO REMOTE FILE SYSTEM AX = 5F05h DL = drive number (0=A:) DS:SI -> ASCIZ name of the object to map the drive to Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful SeeAlso: AX=5F06h"STARLITE",INT 60/AX=0002h --------N-215F06----------------------------- INT 21 U - Network - GET FULL REDIRECTION LIST AX = 5F06h ??? Return: ??? Notes: similar to AX=5F02h and AX=5F05h, but also returns redirections excluded from those calls for various reasons calls INT 2F/AX=111Eh with AX on top of the stack SeeAlso: AX=5F05h"DOS",INT 2F/AX=111Eh --------O-215F06----------------------------- INT 21 - STARLITE architecture - UNMAP DRIVE LETTER AX = 5F06h DL = drive to be unmapped (0=A:) Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful SeeAlso: AX=5F05h"STARLITE",INT 60/AX=0003h --------D-215F07----------------------------- INT 21 - DOS 5+ - ENABLE DRIVE AX = 5F07h DL = drive number (0=A:) Return: CF clear if successful CF set on error AX = error code (0Fh) (see #0885 at AH=59h) Notes: simply sets the "valid" bit in the drive's CDS this function is not supported by Novell DOS 7 through at least Update 4, but support was added by Update 13 SeeAlso: AH=52h,AX=5F08h"DOS" --------O-215F07----------------------------- INT 21 - STARLITE architecture - MAKE NAMED OBJECT AVAILABLE ON NETWORK AX = 5F07h DS:SI -> ASCIZ name of object to offer to network ES:DI -> ASCIZ name under which object will be known on the network MUST begin with three slashes Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful SeeAlso: AX=5F08h"STARLITE" --------D-215F08----------------------------- INT 21 - DOS 5+ - DISABLE DRIVE AX = 5F08h DL = drive number (0=A:) Return: CF clear if successful CF set on error AX = error code (0Fh) (see #0885 at AH=59h) Notes: simply clears the "valid" bit in the drive's CDS this function is not supported by Novell DOS 7 through at least Update 4, but support was added by Update 13 SeeAlso: AH=52h,AX=5F07h"DOS" --------O-215F08----------------------------- INT 21 - STARLITE architecture - REMOVE GLOBAL NETWORK NAME OF OBJECT AX = 5F08h DS:SI -> ASCIZ network name (not local name) of object to unshare Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful SeeAlso: AX=5F07h"STARLITE" --------O-215F09----------------------------- INT 21 - STARLITE architecture - BIND TO NETWORK DEVICE AX = 5F09h DS:DX -> ASCIZ name of the device driver to attach to Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful Note: the STARLITE distributed file system can attach to multiple networks simultaneously SeeAlso: AX=5F0Ah --------O-215F0A----------------------------- INT 21 - STARLITE architecture - DETACH FROM NETWORK DEVICE AX = 5F0Ah DS:DX -> ASCIZ name of device driver to detach from Return: CF set on error AX = error code (see #0885 at AH=59h) CF clear if successful SeeAlso: AX=5F09h --------N-215F30----------------------------- INT 21 U - LAN Manager Enhanced DOS - GET REDIRECTOR VERSION AX = 5F30h Return: AX = version (AH=major,AL=minor) --------N-215F32----------------------------- INT 21 u - Named Pipes - LOCAL DosQNmPipeInfo AX = 5F32h BX = handle CX = size of _PIPEINFO structure DX = level (must be 0001h) DS:SI -> _PIPEINFO structure (see #0906) Return: CF clear if successful _PIPEINFO structure filled in CF set on error AX = error code Note: this function was introduced by LAN Manager but is also supported by the Novell DOS Named Pipe Extender, Banyan VINES, OS/2 Virtual DOS Machines, and others SeeAlso: AX=5F33h,AX=5F34h Format of Named Pipes _PIPEINFO structure: Offset Size Description (Table 0906) 00h WORD size of outgoing buffer 02h WORD size of incoming buffer 04h BYTE maximum number of instances allowed 05h BYTE current number of instances 06h BYTE length of the name (including terminating NUL) 07h N BYTEs name --------N-215F33----------------------------- INT 21 u - Named Pipes - LOCAL DosQNmPHandState AX = 5F33h BX = handle Return: CF clear if successful AH = pipe mode bit mask (see #0907) AL = maximum number of instances CF set on error AX = error code Note: this function was introduced by LAN Manager but is also supported by the Novell DOS Named Pipe Extender, Banyan VINES, OS/2 Virtual DOS Machines, and others SeeAlso: AX=5F32h,AX=5F34h Bitfields for Named Pipes pipe mode: Bit(s) Description (Table 0907) 7 set if nonblocking, clear if blocking 6 set if server end, clear if client end 2 set if write in message mode, clear if write in byte mode 0 set if read in message mode, clear if read in byte mode --------N-215F34----------------------------- INT 21 u - Named Pipes - LOCAL DosSetNmPHandState AX = 5F34h BX = handle CX = pipe mode bit mask bit 15: set if nonblocking, clear if blocking bit 8: set if read in message mode, clear if read in byte mode Return: CF clear if successful CF set if error AX = error code Note: this function was introduced by LAN Manager but is also supported by the Novell DOS Named Pipe Extender, Banyan VINES, OS/2 Virtual DOS Machines, and others SeeAlso: AX=5F32h,AX=5F33h,AX=5F36h --------N-215F35----------------------------- INT 21 u - Named Pipes - LOCAL DosPeekNmPipe AX = 5F35h BX = handle CX = buffer length DS:SI -> buffer Return: CF set on error AX = error code CF clear if successful (LAN Manager v1-v2) AX = 0000h if successful (LAN Manager 3.x) ---if successful--- CX = bytes read SI = bytes left in the pipe DX = bytes left in the current message AX = pipe status (v1-v2) (see #0908) DI = pipe status (v3.x) Note: this function was introduced by LAN Manager but is also supported by the Novell DOS Named Pipe Extender, Banyan VINES, OS/2 Virtual DOS Machines, and others SeeAlso: AX=5F38h,AX=5F39h,AX=5F51h (Table 0908) Values for pipe status: 0001h disconnected 0002h listening 0003h connected 0004h closing --------N-215F36----------------------------- INT 21 u - Named Pipes - LOCAL DosTransactNmPipe AX = 5F36h BX = handle CX = in buffer length DS:SI -> in buffer DX = out buffer length ES:DI -> out buffer Return: CF clear if successful CX = bytes read CF set on error AX = error code Note: this function was introduced by LAN Manager but is also supported by the Novell DOS Named Pipe Extender, Banyan VINES, OS/2 Virtual DOS Machines, and others SeeAlso: AX=5F34h,AX=5F37h --------N-215F37----------------------------- INT 21 u - Named Pipes - DosCallNmPipe AX = 5F37h DS:SI -> DosCallNmPipe stack frame (see #0909) Return: CF clear if successful CX = bytes read CF set on error AX = error code Note: this function was introduced by LAN Manager but is also supported by the Novell DOS Named Pipe Extender, Banyan VINES, OS/2 Virtual DOS Machines, and others SeeAlso: AX=5F36h,AX=5F38h Format of Named Pipes DosCallNmPipe stack frame: Offset Size Description (Table 0909) 00h DWORD timeout 04h DWORD -> bytes read WORD (not used!!) 08h WORD out buffer length 0Ah DWORD address of out buffer 0Eh WORD in buffer length 10h DWORD address of in buffer 14h DWORD address of pipe name --------N-215F38----------------------------- INT 21 u - Named Pipes - LOCAL DosWaitNmPipe - AWAIT AVAIL. OF PIPE INSTANCE AX = 5F38h DS:DX -> pipe name BX:CX = timeout value Return: CF clear if successful CF set if error AX = error code Notes: when a client gets a return code of ERROR_PIPE_BUSY on attempting to open a pipe, it should issue this call to wait until the pipe instance becomes available again; on return from this call, the client must attempt to open the pipe once again this function was introduced by LAN Manager but is also supported by the Novell DOS Named Pipe Extender, Banyan VINES, OS/2 Virtual DOS Machines, and others SeeAlso: AX=5F37h,AX=5F39h --------N-215F39----------------------------- INT 21 U - Named Pipes - LOCAL DosRawReadNmPipe AX = 5F39h BX = handle CX = buffer length DS:DX -> buffer Return: CF clear if successful CX = bytes read CF set if error AX = error code Notes: this function was introduced by LAN Manager but is also supported by the Novell DOS Named Pipe Extender, Banyan VINES, OS/2 Virtual DOS Machines, and others not documented in the LAN Manager Toolkit SeeAlso: AX=5F35h,AX=5F3Ah,INT 2F/AX=1186h --------N-215F3A----------------------------- INT 21 U - Named Pipes - LOCAL DosRawWriteNmPipe AX = 5F3Ah BX = handle CX = buffer length DS:DX -> buffer Return: CF clear if successful CX = bytes written CF set if error AX = error code Notes: this function was introduced by LAN Manager but is also supported by the Novell DOS Named Pipe Extender, Banyan VINES, OS/2 Virtual DOS Machines, and others not documented in the LAN Manager Toolkit SeeAlso: AX=5F39h,AX=5F3Bh,INT 2F/AX=118Fh --------N-215F3B----------------------------- INT 21 u - LAN Manager Enhanced DOS - NetHandleSetInfo AX = 5F3Bh BX = handle CX = handle_info_1 structure length or sizeof DWORD DI = parameter number to set 0000h all 0001h number of milliseconds 0002h number of characters DS:DX -> handle_info_1 structure (DI=0000h) (see #0910) or DWORD (DI=0001h or 0002h) SI = level of information (0001h) Return: CF clear if successful CX = total bytes available CF set if error AX = error code SeeAlso: AX=5F3Ch Format of LAN Manager handle_info_1 structure: Offset Size Description (Table 0910) 00h DWORD number of milliseconds which workstation collects data before it sends the data to the named pipe 04h DWORD number of characters which workstation collects before it sends the data to the named pipe --------N-215F3C----------------------------- INT 21 u - LAN Manager Enhanced DOS - NetHandleGetInfo AX = 5F3Ch BX = handle CX = length of handle_info_1 structure DS:DX -> handle_info_1 structure (see #0910) SI = level of information (must be 0001h) Return: CF clear if successful CX = total bytes available CF set if error AX = error code SeeAlso: AX=5F3Bh --------N-215F3D----------------------------- INT 21 U - LAN Manager Enhanced DOS - WRITE MAILSLOT??? AX = 5F3Dh ??? Return: ??? --------N-215F3E----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetSpecialSMB AX = 5F3Eh ??? Return: ??? Note: This function is not documented anywhere in the LAN Manager 2.x Toolkit but was documented in LAN Manager 1.x manuals. --------N-215F3F----------------------------- INT 21 U - LAN Manager Enhanced DOS - REMOTE API CALL AX = 5F3Fh CX = api number ES:DI -> data descriptor ES:SI -> parameter descriptor ES:DX -> auxiliary descriptor (if DX <> 0) ??? Return: ??? --------N-215F40----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetMessageBufferSend AX = 5F40h DS:DX -> NetMessageBufferSend parameter structure (see #0911) Return: AX = error code Format of LAN Manager NetMessageBufferSend parameter structure: Offset Size Description (Table 0911) 00h DWORD -> recipient name (name for specific user, name* for domain wide name, * for broadcast) 04h DWORD -> buffer 08h WORD length of buffer --------N-215F41----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetServiceEnum AX = 5F41h BL = level of detail (0000h, 0001h or 0002h) CX = buffer length ES:DI -> buffer of service_info_0, service_info_1, or service_info_2 (see #0912,#0913,#0914) Return: CF clear if successful CX = entries read DX = total available CF set on error AX = error code Format of LAN Manager service_info_0 structure: Offset Size Description (Table 0912) 00h 16 BYTEs name SeeAlso: #0913,#0914 Format of service_info_1 structure: Offset Size Description (Table 0913) 00h 16 BYTEs name 10h WORD status bitmask (see #0915) 12h DWORD status code (see #0916) (also see Microsoft LAN Manager Programmer's Reference) 16h WORD process id SeeAlso: #0912,#0914 Format of service_info_2 structure: Offset Size Description (Table 0914) 00h 16 BYTEs name 10h WORD status bitmask (see #0915) 12h DWORD status code (see #0916) 16h WORD process id 18h 64 BYTEs text SeeAlso: #0912,#0913 Bitfields for LAN Manager status bitmask: Bit(s) Description (Table 0915) 0,1 00 uninstall 01 install pending 10 uninstall pending 11 installed 2,3 00 active 01 Continue pending 10 Pause pending 11 paused 4 uninstallable 5 pausable 8 disk redirector paused 9 spooled device redirector paused (printing) 10 communication device redirector paused (Table 0916) Values for LAN Manager status code: high word 3051 Bad parameter value 3052 A parameter is missing 3053 An unknown parameter was specified 3054 The resource is insufficient 3055 Configuration is faulty 3056 An MS-DOS or MS OS/2 error occured 3057 An internal error occured 3058 An ambiguous parameter name was given 3059 A duplicate parameter exists 3060 The service was terminated by NetSeviceControl when it did not respond 3061 The service program file could not be executed 3062 The subservice failed to start 3063 There is a conflict in the value or use of these parameters 3064 There is a problem with the file low word 3070 There is insufficient memory 3071 There is insufficeient disk space 3072 Unable to create thread 3073 Unable to create process 3074 A security failure occured 3075 There is bad or missing default path 3076 Network software is not installed 3077 Server software is not installed 3078 The server could not access the UAS database 3079 The action requires user-level security 3080 The log directory is invalid 3081 The LAN group specificed could not be used 3082 The computername is being used as a message alias on another computer 3083 The workstation failed to announce the servername 3084 The user accounts system is not configured properly --------N-215F42----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetServiceControl AX = 5F42h DH = opcode 00h interrogate status 01h pause 02h continue 03h uninstall DL = argument 01h disk resource 02h print resource 04h communications resource (not implemented for DOS) ES:BX -> NetServiceControl parameter structure (see #0917) Return: CF clear if successful CF set on error AX = error code Format of LAN Manager NetServiceControl parameter structure: Offset Size Description (Table 0917) 00h DWORD -> service name 04h WORD result buffer size 06h DWORD -> result buffer as service_info_2 structure --------N-215F43----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL DosPrintJobGetId AX = 5F43h BX = handle of remote print job CX = size of PRIDINFO struture ES:DI -> PRIDINFO structure (see #0918) Return: CF clear if successful PRIDINFO filled in CF set on error AX = error code Format of LAN Manager PRIDINFO structure: Offset Size Description (Table 0918) 00h WORD job id 02h 16 BYTEs server name 12h 13 BYTEs queue name 1Fh 1 BYTE pad --------N-215F44----------------------------- INT 21 - LAN Manager Enhanced DOS - LOCAL NetWkstaGetInfo AX = 5F44h BX = information level (00h, 01h, or 0Ah) CX = buffer size ES:DI -> buffer in which to store info (see #2715,#2716,#2717) Return: AX = error code DX = amount of buffer used (or required) SeeAlso: AX=5F45h,AX=5F49h Format of LAN Manager wksta_info_0 structure: Offset Size Description (Table 2715) 00h WORD reserved (0) 02h DWORD reserved (0) 06h DWORD -> path to computer's LANMAN directory 0Ah DWORD -> computername of the workstation 0Eh DWORD -> username of user logged onto workstation 12h DWORD -> domain to which workstation belongs 16h WORD LAN Manager version number (2 bytes, Major, Minor) 18h DWORD reserved (0) 22h WORD number of seconds workstation waits for resource availability 24h DWORD delay (in millsecs) before sending data to resource 28h WORD reserved (0) 2Ah WORD reserved (0) 2Ch WORD number of seconds to maintain an inactive connection 2Eh WORD number of seconds an inactive search continues 30h WORD threads to dedicate to network (not supported in MSDOS) 32h WORD number of simultaneous commands sent to network 34h WORD reserved6 (must be 0) 36h WORD number of internal buffers 38h WORD size (in bytes) of each internal buffer 3Ah WORD max size (in bytes) of an internal cache buffer (not MSDOS) 3Ch WORD seconds before disconnecting inactive session (not MSDOS) 3Eh WORD size (in bytes) of an internal error buffer (not MSDOS) 40h WORD number of clients that can receive alert messages (not MSDOS) 42h WORD number of services that can be started on workstation 44h WORD max size (in kilobytes) of error log (not MSDOS) 46h WORD number of secs before closing inactive print jobs (not MSDOS) 48h WORD number of character buffers for workstation 4Ah WORD max size (in bytes) of character buffer 4Ch DWORD -> name of server that validated logon 50h DWORD -> workstation heuristics 52h WORD number of mailslots allowed SeeAlso: #2716,#2717 Format of LAN Manager wksta_info_1 structure: Offset Size Description (Table 2716) 00h 84 BYTEs wksta_info_0 structure (see #2715) 54h DWORD -> name of domain which user is logged on to 58h DWORD -> all domains in which computer is enlisted 5Ch WORD number of buffers to allocate for receiving datagrams SeeAlso: #2717 Format of LAN Manager wksta_info_10 structure: Offset Size Description (Table 2717) 00h DWORD -> computername of the workstation 04h DWORD -> username of user logged onto workstation 08h DWORD -> domain to which workstation belongs 0Ch WORD LAN Manager version number (2 bytes, Major, Minor) 0Eh DWORD -> name of domain which user is loggod on to 12h DWORD -> all domains in which computer is enlisted SeeAlso: #2715,#2716 --------N-215F45----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetWkstaSetInfo AX = 5F45h BX = level (0000h or 0001h) CX = buffer size DX = parameter to set ES:DI -> buffer Return: CF clear if successful CF set if error AX = error code SeeAlso: AX=5F44h --------N-215F46----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetUseEnum AX = 5F46h BX = level (0000h or 0001h) CX = size of buffer ES:DI -> buffer of use_info_0 or use_info_1 structures (see #0919,#0920) Return: CF clear if successful CX = entries read DX = total available entries CF set if error AX = error code SeeAlso: AX=5F47h,AX=5F48h,AX=5F4Ch Format of LAN Manager use_info_0 structure: Offset Size Description (Table 0919) 00h 9 BYTEs local device name 09h BYTE padding 0Ah DWORD -> remote device name in UNC form \\server\share SeeAlso: #0920 Format of LAN Manager use_info_1 structure: Offset Size Description (Table 0920) 00h 9 BYTEs Local device name 09h BYTE padding 0Ah DWORD -> remote device name in UNC form \\server\share 0Eh DWORD -> password 12h WORD network link status (00h OK, 02h disconnected, else unsure) 14h WORD use type (-1 wildcard, 0 disk, 1 print, 2 com, 3 ipc) 16h WORD ignored 18h WORD ignored SeeAlso: #0919 --------N-215F47----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetUseAdd AX = 5F47h BX = level (0001h) CX = size of use_info_1 structure ES:DI -> use_info_1 structure (see #0920) Return: CF clear on success CF set on error AX = error code SeeAlso: AX=5F46h,AX=5F48h --------N-215F48----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetUseDel AX = 5F48h BX = force level 0000h no force 0001h force 0002h lots of force ES:DI -> buffer as either the local device name or UNC remote name Return: CF clear on success CF set on error AX = error code SeeAlso: AX=5F46h,AX=5F48h,AX=5F49h --------N-215F49----------------------------- INT 21 u - LAN Manager Enhanced DOS - NetUseGetInfo AX = 5F49h DS:DX -> NetUseGetInfo parameter structure (see #0921) Return: CF clear on success DX = total available CF set on error AX = error code SeeAlso: AX=5F44h,AX=5F47h Format of LAN Manager NetUseGetInfo parameter structure: Offset Size Description (Table 0921) 00h DWORD pointer to either the local device name or UNC remote name 04h WORD level of information (0000h or 0001h) 06h DWORD pointer to buffer of use_info_0 or use_info_1 structures 0Ah WORD length of buffer --------N-215F4A----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetRemoteCopy AX = 5F4Ah DS:DX -> NetRemoteCopy parameter structure (see #0922) Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5F4Bh Format of LAN Manager NetRemoteCopy parameter structure: Offset Size Description (Table 0922) 00h DWORD -> source name as UNC 04h DWORD -> destination name as UNC 08h DWORD -> source password 0Ch DWORD -> destination password 10h WORD destination open bitmap if destination path exists 0000h open fails 0001h file is appended 0002h file is overwritten if destination path doesn't exist 0000h open fails 0010h file is created 12h WORD copy control bitmap (see #0923) 14h DWORD -> copy_info buffer 18h WORD length of copy_info buffer Bitfields for LAN Manager copy control: Bit(s) Description (Table 0923) 0 destination must be a file 1 destination must be a directory 2 destination is opened in ascii mode instead of binary 3 source is opened in ascii mode instead of binary 4 verify all write operations --------N-215F4B----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetRemoteMove AX = 5F4Bh DS:DX -> NetRemoteMove parameter structure (see #0924) Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5F4Ah Format of LAN Manager NetRemoteMove parameter structure: Offset Size Description (Table 0924) 00h DWORD -> source name as UNC 04h DWORD -> destination name as UNC 08h DWORD -> source password 0Ch DWORD -> destination password 10h WORD destination open bitmap if destination path exists 0000h open fails 0001h file is appended 0002h file is overwritten if destination path doesn't exist 0000h open fails 0010h file is created 12h WORD move control bitmap 0001h destination must be a file 0002h destination must be a directory 14h DWORD -> move_info buffer 18h WORD length of move_info buffer --------N-215F4C----------------------------- INT 21 u - LAN Manager Enhanced DOS - LOCAL NetServerEnum AX = 5F4Ch BX = level (0000h or 0001h) CX = buffer length ES:DI -> buffer in which to store information Return: CF clear if successful ES:DI -> server_info_X structures (depending on level) (see #0925,#0926) BX = entries read CX = total entries available CF set on error AX = error code Notes: this function is also supported by the Novell DOS Named Pipe Extender this function has been obseleted by NetServerEnum2 SeeAlso: AX=5F53h Format of LAN Manager server_info_0 structure: Offset Size Description (Table 0925) 00h 16 BYTEs name SeeAlso: #0926 Format of LAN Manager server_info_1 structure: Offset Size Description (Table 0926) 00h 16 BYTEs name 10h BYTE major version in lower nibble 11h BYTE minor version 12h DWORD server type bitmask (see #0927) 16h DWORD -> comment string SeeAlso: #0925 Bitfields for LAN Manager server type: Bit(s) Description (Table 0927) 0 workstation 1 server 2 SQL server 3 primary domain controller 4 backup domain controller 5 time server 6 Apple File Protocol (AFP) server 7 Novell server 8 Domain Member (v2.1+) 9 Print Queue server (v2.1+) 10 Dialin server (v2.1+) 11 Unix server (v2.1+) --------N-215F4D----------------------------- INT 21 u - LAN Manager Enhanced DOS - DosMakeMailslot AX = 5F4Dh BX = message size CX = mailslot size (must be bigger than message size by at least 1) (minimum 1000h, maximum FFF6h) (buffer must be 9 bytes bigger than this) DS:SI -> name ES:DI -> memory buffer Return: CF clear if successful AX = handle CF set on error AX = error code SeeAlso: AX=5F4Eh,AX=5F4Fh,AX=5F50h,AX=5F51h --------N-215F4E----------------------------- INT 21 u - LAN Manager Enhanced DOS - DosDeleteMailslot AX = 5F4Eh BX = handle Return: CF clear if successful ES:DI -> memory to be freed (allocated during DosMakeMailslot) CF set on error AX = error code SeeAlso: AX=5F4Dh,AX=5F4Fh --------N-215F4F----------------------------- INT 21 u - LAN Manager Enhanced DOS - DosMailslotInfo AX = 5F4Fh BX = handle Return: CF clear if successful AX = max message size BX = mailslot size CX = next message size DX = next message priority SI = number of messages waiting CF set on error AX = error code SeeAlso: AX=5F4Dh,AX=5F4Eh,AX=5F50h --------N-215F50----------------------------- INT 21 u - LAN Manager Enhanced DOS - DosReadMailslot AX = 5F50h BX = handle DX:CX = timeout ES:DI -> buffer Return: CF clear if successful AX = bytes read CX = next item's size DX = next item's priority CF set on error AX = error code SeeAlso: AX=5F4Dh,AX=5F4Fh,AX=5F51h,AX=5F52h --------N-215F51----------------------------- INT 21 u - LAN Manager Enhanced DOS - DosPeekMailslot AX = 5F51h BX = handle ES:DI -> buffer Return: CF clear if successful AX = bytes read CX = next item's size DX = next item's priority CF set on error AX = error code SeeAlso: AX=5F35h,AX=5F4Fh,AX=5F50h,AX=5F52h --------N-215F52----------------------------- INT 21 u - LAN Manager Enhanced DOS - DosWriteMailslot AX = 5F52h BX = class CX = length of buffer DX = priority ES:DI -> DosWriteMailslot parameter structure (see #0928) DS:SI -> mailslot name Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5F4Fh,AX=5F50h,AX=5F51h Format of LAN Manager DosWriteMailslot parameter structure: Offset Size Description (Table 0928) 00h DWORD timeout 04h DWORD -> buffer --------N-215F53----------------------------- INT 21 u - LAN Manager Enhanced DOS - NetServerEnum2 AX = 5F53h DS:SI -> NetServerEnum2 parameter structure (see #0929) Return: CF clear if successful BX = entries read CX = total entries available CF set on error AX = error code SeeAlso: AX=5F4Ch Format of LAN Manager NetServerEnum2 parameter structure: Offset Size Description (Table 0929) 00h WORD level (0000h or 0001h) 02h DWORD -> buffer as array of server_info_??? structures (see #0931) 06h WORD length of buffer 08h DWORD server type bitmask (see #0930) 0Ch DWORD -> Domain name (may be 0000h:0000h for all local domains) Bitfields for LAN Manager server type: Bit(s) Description (Table 0930) 0 workstation 1 server 2 SQL server 3 primary domain controller 4 backup domain controller 5 time server 6 Apple File Protocol (AFP) server 7 Novell server 8 Domain Member (v2.1+) 9 Print Queue server (v2.1+) 10 Dialin server (v2.1+) 11 Unix server (v2.1+) Note: set all (FFFFFFFFh) for All Types Format of LAN Manager server_info_0 structure: Offset Size Description (Table 0931) 00h 16 BYTEs name SeeAlso: #0932 Format of LAN Manager server_info_1 structure: Offset Size Description (Table 0932) 00h 16 BYTEs name 10h BYTE major version in lower nibble 11h BYTE minor version 12h DWORD server type (bits 0-11) (see #0930) 16h DWORD -> comment string SeeAlso: #0931 --------N-215F55---------------------------- INT 21 U - LAN Manager Enhanced DOS - KILL ALL CONNECTIONS??? AX = 5F55h BX = ??? Return: CF clear if successful CF set on error AX = error code --------N-215F80----------------------------- INT 21 - LANtastic - GET LOGIN ENTRY AX = 5F80h BX = login entry index (0-based) ES:DI -> 16-byte buffer for machine name Return: CF clear if successful buffer filled with machine name ("\\" prefix removed) DL = adapter number (v3+) CF set on error AX = error code Note: the login entry index corresponds to the value BX used in AX=5F83h SeeAlso: AX=5F83h --------N-215F81----------------------------- INT 21 - LANtastic - LOGIN TO SERVER AX = 5F81h ES:DI -> ASCIZ login path followed immediately by ASCIZ password BL = adapter number FFh try all valid adapters 00h-07h try only specified adapter Return: CF clear if successful CF set on error AX = error code Notes: login path is of form "\\machine\username" if no password is used, the string at ES:DI must be terminated with three NULs for compatibility with LANtastic v3.0. SeeAlso: AX=5F82h,AX=5F84h --------N-215F82----------------------------- INT 21 - LANtastic - LOGOUT FROM SERVER AX = 5F82h ES:DI -> ASCIZ server name (in form "\\machine") Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5F81h,AX=5F88h,AX=5FCBh --------N-215F83----------------------------- INT 21 - LANtastic - GET USERNAME ENTRY AX = 5F83h BX = login entry index (0-based) ES:DI -> 16-byte buffer for username currently logged into Return: CF clear if successful DL = adapter number (v3+) CF set on error AX = error code Note: the login entry index corresponds to the value BX used in AX=5F80h SeeAlso: AX=5F80h --------N-215F84----------------------------- INT 21 - LANtastic - GET INACTIVE SERVER ENTRY AX = 5F84h BX = server index not currently logged into ES:DI -> 16-byte buffer for server name which is available for logging in to ("\\" prefix omitted) Return: CF clear if successful DL = adapter number to non-logged in server is on CF set on error AX = error code SeeAlso: AX=5F81h --------N-215F85----------------------------- INT 21 - LANtastic - CHANGE PASSWORD AX = 5F85h ES:DI -> buffer containing "\\machine\oldpassword" 00h "newpassword"00h Return: CF clear if successful CF set on error AX = error code Notes: must be logged into the named machine this function is illegal for group accounts --------N-215F86----------------------------- INT 21 - LANtastic - DISABLE ACCOUNT AX = 5F86h ES:DI -> ASCIZ machine name and password in form "\\machine\password" Return: CF clear if successful CF set on error AX = error code Note: must be logged into the named machine and concurrent logins set to 1 by NET_MGR. Requires system manager to re-enable account. --------N-215F87----------------------------- INT 21 - LANtastic v3+ - GET ACCOUNT AX = 5F87h DS:SI -> 128-byte buffer for account information (see #0933) ES:DI -> ASCIZ machine name in form "\\machine" Return: CF clear if successful CF set on error AX = error code BX destroyed Note: must be logged into the specified machine Format of LANtastic user account structure: Offset Size Description (Table 0933) 00h 16 BYTEs blank-padded username (zero-padded for v4.x) 10h 16 BYTEs reserved (00h) 20h 32 BYTEs user description 40h BYTE privilege bits (see #0934) 41h BYTE maximum concurrent users 42h 42 BYTEs bit map for disallowed half hours, beginning on Sunday (bit set if half-hour not an allowed time) 6Ch WORD internal (0002h) 6Eh 2 WORDs last login time 72h 2 WORDs account expiration date (MS-DOS-format year/month:day) 76h 2 WORDs password expiration date (0 = none) 7Ah BYTE number of days to extend password after change (1-31) 00h if no extension required ---v3.x--- 7Bh 5 BYTEs reserved ---v4.x--- 7Bh BYTE storage for first letter of user name when deleted (first character is changed to 00h when deleting account) 7Ch BYTE extended privileges 7Dh 3 BYTEs reserved Bitfields for LANtastic privilege bits: Bit(s) Description (Table 0934) 7 bypass access control lists 6 bypass queue protection 5 treat as local process 4 bypass mail protection 3 allow audit entry creation 2 system manager 0 user cannot change password --------N-215F88----------------------------- INT 21 - LANtastic v4.0+ - LOGOUT FROM ALL SERVERS AX = 5F88h Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5F82h --------N-215F97----------------------------- INT 21 - LANtastic - COPY FILE AX = 5F97h CX:DX = number of bytes to copy (FFFFFFFFh = entire file) SI = source file handle DI = destination file handle Return: CF clear if successful DX:AX = number of bytes copied CF set on error AX = error code Note: copy is performed by server --------N-215F98----------------------------- INT 21 - LANtastic - SEND UNSOLICITED MESSAGE AX = 5F98h DS:SI -> message buffer (see #0935) Return: CF clear if successful CF set on error AX = error code Note: v4.1- return no errors SeeAlso: AX=5F99h Format of LANtastic message buffer: Offset Size Description (Table 0935) 00h BYTE reserved 01h BYTE message type 00h general 01h server warning 02h-7Fh reserved 80h-FFh user-defined 02h 16 BYTEs ASCIZ destination machine name 12h 16 BYTEs ASCIZ server name which user must be logged into 22h 16 BYTEs ASCIZ user name 32h 16 BYTEs ASCIZ originating machine name (filled in when received) 42h 80 BYTEs message text --------N-215F99----------------------------- INT 21 - LANtastic - GET LAST RECEIVED UNSOLICITED MESSAGE AX = 5F99h ES:DI -> messsage buffer (see #0935) Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5F98h --------N-215F9A----------------------------- INT 21 - LANtastic - GET MESSAGE PROCESSING FLAGS AX = 5F9Ah Return: CF clear if successful DL = bits describing processing of received messages (see #0936) CF set on error AX = error code SeeAlso: AX=5F9Bh,AX=5F9Ch,AX=5F9Dh Bitfields for unsolicited message processing flags: Bit(s) Description (Table 0936) 0 beep before message is delivered 1 deliver message to message service 2 pop up message automatically (v3+) --------N-215F9B----------------------------- INT 21 - LANtastic - SET MESSAGE PROCESSING FLAGS AX = 5F9Bh DL = bits describing processing for received unsolicited messages (see #0936) Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5F9Ah,AX=5F9Eh --------N-215F9C----------------------------- INT 21 - LANtastic v3+ - POP UP LAST RECEIVED MESSAGE AX = 5F9Ch CX = time to leave on screen in clock ticks DH = 0-based screen line on which to place message Return: CF clear if successful CF set on error AX = error code (0Bh) Notes: the original screen contents are restored when the message is removed the message will not appear, and an error will be returned, if the screen is in a graphics mode SeeAlso: AX=5F9Ah --------N-215F9D----------------------------- INT 21 - LANtastic v4.1+ - GET REDIRECTOR CONTROL BITS AX = 5F9Dh Return: DL = redirector control bits bit 7: set to notify on print job completion SeeAlso: AX=5F9Ah,AX=5F9Eh --------N-215F9E----------------------------- INT 21 - LANtastic v4.1+ - SET REDIRECTOR CONTROL BITS AX = 5F9Eh DL = redirector control bits (see AX=5F9Dh) Return: nothing SeeAlso: AX=5F9Bh,AX=5F9Dh --------N-215FA0----------------------------- INT 21 - LANtastic - GET QUEUE ENTRY AX = 5FA0h BX = queue entry index (0000h is first entry) DS:SI -> buffer for queue entry (see #0937) ES:DI -> ASCIZ server name in form "\\name" Return: CF clear if successful CF set on error AX = error code BX = entry index for next queue entry (BX-1 is current index) SeeAlso: AX=5FA1h,AX=5FA2h Format of LANtastic queue entry: Offset Size Description (Table 0937) 00h BYTE status of entry (see #0938) 01h DWORD size of spooled file 05h BYTE type of entry (see #0939) 06h BYTE output control (see #0940) 07h WORD number of copies 09h DWORD sequence number of queue entry 0Dh 48 BYTEs pathname of spooled file 3Dh 16 BYTEs user who spooled file 4Dh 16 BYTEs name of machine from which file was spooled 5Dh WORD date file was spooled (see #0877 at AX=5700h) 5Fh WORD time file was spooled (see #0876 at AX=5700h) 61h 17 BYTEs ASCIZ destination device or user name 72h 48 BYTEs comment field (Table 0938) Values for status of LANtastic queue entry: 00h empty 01h being updated 02h being held 03h waiting for despool 04h being despooled 05h canceled 06h spooled file could not be accessed 07h destination could not be accessed 08h rush job (Table 0939) Values for type of LANtastic queue entry: 00h printer queue file 01h message 02h local file 03h remote file 04h to remote modem 05h batch processor file Bitfields for output control: Bit(s) Description (Table 0940) 6 don't delete (for mail) 5 mail file contains voice mail (v3+) 4 mail message has been read 3 response has been requested for this mail --------N-215FA1----------------------------- INT 21 - LANtastic - SET QUEUE ENTRY AX = 5FA1h BX = handle of opened queue entry DS:SI -> queue entry (see #0937) Return: CF clear if successful CF set on error AX = error code Notes: the only queue entry fields which may be changed are output control, number of copies, destination device, and comment the handle in BX is that from a create or open (INT 21/AH=3Ch,3Dh) call on the file "\\server\\@MAIL" or "\\server\@name" (for printer queue entries) SeeAlso: AX=5FA0h,AX=5FA2h,AX=5FA9h --------N-215FA2----------------------------- INT 21 - LANtastic - CONTROL QUEUE AX = 5FA2h BL = control command 00h start despooling (privileged) 01h halt despooling (privileged) 02h halt despooling at end of job (privileged) 03h pause despooler at end of job (privileged) 04h print single job (privileged) 05h restart current job (privileged) 06h cancel the current job 07h hold queue entry 08h release a held queue entry 09h make queue entry a rushed job (privileged) CX:DX = sequence number to control (commands 06h-09h) DX = physical printer number (commands 00h-05h) 00h-02h LPT1-LPT3 03h,04h COM1,COM2 other all printers ES:DI -> ASCIZ server name in form "\\machine" Return: CF clear if successful CF set on error AX = error code --------N-215FA3----------------------------- INT 21 - LANtastic v3+ - GET PRINTER STATUS AX = 5FA3h BX = physical printer number (00h-02h = LPT1-LPT3, 03h-04h = COM1-COM2) DS:SI -> buffer for printer status (see #0941) ES:DI -> ASCIZ server name in form "\\machine" Return: CF clear if successful CF set on error AX = error code BX = next physical printer number Note: you must be logged in to the specified server Format of LANtastic printer status: Offset Size Description (Table 0941) 00h BYTE printer state (see #0942) 01h WORD queue index of print job being despooled FFFFh if not despooling--ignore all following fields 03h WORD actual characters per second being output 05h DWORD number of characters actually output so far 09h DWORD number of bytes read from spooled file so far 0Dh WORD copies remaining to print Bitfields for LANtastic printer state: Bit(s) Description (Table 0942) 7 printer paused 0-6 0 printer disabled 1 will stop at end of job 2 print multiple jobs --------N-215FA4----------------------------- INT 21 - LANtastic v3+ - GET STREAM INFO AX = 5FA4h BX = 0-based stream index number DS:SI -> buffer for stream information (see #0943) ES:DI -> ASCIZ machine name in form "\\machine" Return: CF clear if successful CF set on error AX = error code BX = next stream number SeeAlso: AX=5FA5h Format of LANtastic stream information: Offset Size Description (Table 0943) 00h BYTE queueing of jobs for logical printer (0=disabled,other=enabled) 01h 11 BYTEs logical printer resource template (may contain ? wildcards) --------N-215FA5----------------------------- INT 21 - LANtastic v3+ - SET STREAM INFO AX = 5FA5h BX = 0-based stream index number DS:SI -> buffer containing stream information (see #0943) ES:DI -> ASCIZ machine name in form "\\machine" Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5FA4h --------N-215FA7----------------------------- INT 21 - LANtastic - CREATE USER AUDIT ENTRY AX = 5FA7h DS:DX -> ASCIZ reason code (max 8 bytes) DS:SI -> ASCIZ variable reason string (max 128 bytes) ES:DI -> ASCIZ machine name in form "\\machine" Return: CF clear if successful CF set on error AX = error code Note: you must be logged in to the specified server and have the "U" privilege to execute this call --------N-215FA9----------------------------- INT 21 - LANtastic v4.1+ - SET EXTENDED QUEUE ENTRY AX = 5FA9h BX = handle of opened queue entry DS:SI -> queue entry (see #0937) Return: CF clear if successful CF set on error AX = error code Note: functions exactly the same as AX=5FA1h except the spooled filename is also set. This call supports direct despooling. SeeAlso: AX=5FA1h --------N-215FB0----------------------------- INT 21 - LANtastic - GET ACTIVE USER INFORMATION AX = 5FB0h BX = server login entry index DS:SI -> buffer for active user entry (see #0944) ES:DI -> ASCIZ machine name in form "\\server" Return: CF clear if successful CF set on error AX = error code BX = next login index SeeAlso: AX=5FB2h Format of LANtastic active user entry: Offset Size Description (Table 0944) 00h WORD virtual circuit number 02h BYTE login state (see #0945) 03h BYTE last command issued (see #0946) 04h 5 BYTEs number of I/O bytes (40-bit unsigned number) 09h 3 BYTEs number of server requests (24-bit unsigned) 0Ch 16 BYTEs name of user who is logged in 1Ch 16 BYTEs name of remote logged in machine 2Ch BYTE extended privileges (v4+???) bit 0: user cannot change his password 2Dh WORD time left in minutes (0000h = unlimited) (v4+???) Bitfields for login state: Bit(s) Description (Table 0945) 0 fully logged in 1 remote program load login 2 user has system manager privileges 3 user can create audit entries 4 bypass mail protection 5 treat as local process 6 bypass queue protection 7 bypass access control lists (Table 0946) Values for last LANtastic command: 00h login 01h process termination 02h open file 03h close file 04h create file 05h create new file 06h create unique file 07h commit data to disk 08h read file 09h write file 0Ah delete file 0Bh set file attributes 0Ch lock byte range 0Dh unlock byte range 0Eh create subdirectory 0Fh remove subdirectory 10h rename file 11h find first matching file 12h find next matching file 13h get disk free space 14h get a queue entry 15h set a queue entry 16h control the queue 17h return login information 18h return link description 19h seek on file 1Ah get server's time 1Bh create audit entry 1Ch open file in multitude of modes 1Dh change password 1Eh disable account 1Fh local server file copy ---v3+--- 20h get username from account file 21h translate server's logical path 22h make indirect file 23h get indirect file contents 24h get physical printer status 25h get logical print stream info 26h set logical print stream info 27h get user's account record ---v4+--- 28h request server shutdown 29h cancel server shutdown 2Ah stuff server's keyboard 2Bh write then commit data to disk 2Ch set extended queue entry 2Dh terminate user from server 2Eh enable/disable logins 2Fh flush server caches 30h change username 31h get extended queue entry (same as get queue, but can return named fields blanked) --------N-215FB1----------------------------- INT 21 - LANtastic - GET SHARED DIRECTORY INFORMATION AX = 5FB1h DS:SI -> 64-byte buffer for link description ES:DI -> ASCIZ machine and shared directory name in form "\\machine\shared-resource" Return: CF clear if successful CX = access control list privileges for requesting user (see #0947) CF set on error AX = error code Bitfields for LANtastic access control list: Bit(s) Description (Table 0947) 4 (I) allow expansion of indirect files 5 (A) allow attribute changing 6 (P) allow physical access to device 7 (E) allow program execution 8 (N) allow file renaming 9 (K) allow directory deletion 10 (D) allow file deletion 11 (L) allow file/directory lookups 12 (M) allow directory creation 13 (C) allow file creation 14 (W) allow open for write and writing 15 (R) allow open for read and reading --------N-215FB2----------------------------- INT 21 - LANtastic v3+ - GET USERNAME FROM ACCOUNT FILE AX = 5FB2h BX = username entry index (0 for first) DS:SI -> 16-byte buffer for username ES:DI -> ASCIZ server name in form "\\machine" Return: CF clear if successful CF set on error AX = error code BX = next queue entry index SeeAlso: AX=5FB0h --------N-215FB3----------------------------- INT 21 - LANtastic v3+ - TRANSLATE PATH AX = 5FB3h DS:SI -> 128-byte buffer for ASCIZ result ES:DI -> full ASCIZ path, including server name DX = types of translation to be performed bit 0: expand last component as indirect file bit 1: return actual path relative to server's physical disk Return: CF clear if successful CF set on error AX = error code Note: always expands any indirect files along the path SeeALso: AX=5FB4h,INT 21/AH=60h --------N-215FB4----------------------------- INT 21 - LANtastic v3+ - CREATE INDIRECT FILE AX = 5FB4h DS:SI -> 128-byte buffer containing ASCIZ contents of indirect file ES:DI -> full ASCIZ path of indirect file to create, incl machine name Return: CF clear if successful CF set on error AX = error code Note: the contents of the indirect file may be any valid server-relative path SeeAlso: AX=5FB3h,AX=5FB5h --------N-215FB5----------------------------- INT 21 - LANtastic v3+ - GET INDIRECT FILE CONTENTS AX = 5FB5h DS:SI -> 128-byte buffer for ASCIZ indirect file contents ES:DI -> full ASCIZ path of indirect file Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5FB4h --------N-215FB6----------------------------- INT 21 - LANtastic v4.1+ - SET AUTO-LOGIN DEFAULTS AX = 5FB6h ES:DI -> pointer to ASCIZ default user name, immediately followed by ASCIZ password BL = adapter number to use for default login attempt FFh try all valid adapters 00h-05h try adapter 0-5 explicitly Return: CF clear if successful CF set on error AX = error code Notes: call with ES:DI -> two nulls to disable auto-login SeeAlso: AX=5FB7h --------N-215FB7----------------------------- INT 21 - LANtastic v4.1+ - GET AUTO-LOGIN DEFAULTS AX = 5FB7h ES:DI -> pointer to 16-byte buffer to store ASCIZ auto-login user name Return: CF clear if successful DL = adapter number used for default login attempt FFh all valid adapters will be tried 00h-05h specified adapter will be tried explicitly CF set on error AX = error code SeeAlso: AX=5F81h,AX=5FB6h --------N-215FC0----------------------------- INT 21 - LANtastic - GET TIME FROM SERVER AX = 5FC0h DS:SI -> time block (see #0948) ES:DI -> ASCIZ server name to get time from Return: CF clear if successful CF set on error AX = error code SeeAlso: AH=E7h Format of LANtastic time block: Offset Size Description (Table 0948) 00h WORD year 02h BYTE day 03h BYTE month 04h BYTE minutes 05h BYTE hour 06h BYTE hundredths of second 07h BYTE second --------N-215FC8----------------------------- INT 21 - LANtastic v4.0+ - SCHEDULE SERVER SHUTDOWN AX = 5FC8h ES:DI -> ASCIZ server name in form "\\machine" DS:SI -> ASCIZ reason string (80 characters) CX = number of minutes until shutdown (0 = immediate) DX = option flags (see #0949) Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5FC9h Bitfields for LANtastic option flags: Bit(s) Description (Table 0949) 0 auto reboot 1 do not notify users 2 halt after shutdown 3 shutdown due to power fail (used by UPS) 4-7 reserved 8-14 user definable 15 reserved --------N-215FC9----------------------------- INT 21 - LANtastic v4.0+ - CANCEL SERVER SHUTDOWN AX = 5FC9h ES:DI -> ASCIZ server name in form "\\machine" Return: CF clear if successful CF set on error AX = error code Note: you must have the "S" privilege to use this call SeeAlso: AX=5FC8h --------N-215FCA----------------------------- INT 21 - LANtastic v4.0+ - STUFF SERVER KEYBOARD BUFFER AX = 5FCAh ES:DI -> ASCIZ server name in form "\\machine" DS:SI -> ASCIZ string to stuff (128 bytes) Return: CF clear if successful CF set on error AX = error code Note: you must have the "S" privilege to use this call maximum number of characters that can be stuffed is determined by the server's RUN BUFFER SIZE. SeeAlso: INT 16/AH=05h --------N-215FCB----------------------------- INT 21 - LANtastic v4.1+ - TERMINATE USER AX = 5FCBh ES:DI -> ASCIZ server name in form "\\machine" DS:SI -> blank-padded username. A null char = wildcard. DS:DX -> blank-padded machine name. A null char = wildcard. CX = minutes until termination (0 = immediate) Return: CF clear if successful CF set on error AX = error code Note: you must have the "S" privilege to use this call you cannot log yourself out using this call SeeAlso: AX=5F82h --------N-215FCC----------------------------- INT 21 - LANtastic v4.1+ - GET/SET SERVER CONTROL BITS AX = 5FCCh ES:DI -> ASCIZ server name in form "\\machine" CX = bit values (value of bits you want to set) (see #0950) DX = bit mask (bits you are interested in, 0 = get only) (see #0950) Return: CF clear if successful CX = control bits after call (see #0950) CF set on error AX = error code Note: you must have the "S" privilege to SET, anyone can GET. Bitfields for control bits: Bit(s) Description (Table 0950) 0 disable logins --------N-215FCD----------------------------- INT 21 - LANtastic v4.1+ - FLUSH SERVER CACHES AX = 5FCDh ES:DI -> ASCIZ server name in form "\\machine" Return: CF clear if successful CF set on error AX = error code Note: you must have the "S" privilege to use this call. --------N-215FD0----------------------------- INT 21 - LANtastic - GET REDIRECTED PRINTER TIMEOUT AX = 5FD0h Return: CF clear if successful CX = redirected printer timeout in clock ticks of 55ms 0000h if timeout disabled CF set on error AX = error code SeeAlso: AX=5FD1h --------N-215FD1----------------------------- INT 21 - LANtastic - SET REDIRECTED PRINTER TIMEOUT AX = 5FD1h CX = printer timeout in clock ticks of 55ms, 0000h to disable timeouts Return: CF clear if successful CF set on error AX = error code SeeAlso: AX=5FD0h --------N-215FE0----------------------------- INT 21 C - LANtastic - GET DOS SERVICE VECTOR AX = 5FE0h Return: CF clear if successful ES:BX -> current FAR service routine CF set on error AX = error code Note: the service routine is called by the LANtastic redirector whenever DOS may safely be called, permitting external TSRs and drivers to hook into LANtastic's DOS busy flag checking SeeAlso: AX=5FE1h,INT 28,INT 2A/AH=84h --------N-215FE1----------------------------- INT 21 - LANtastic - SET DOS SERVICE VECTOR AX = 5FE1h ES:BX -> FAR routine to call when DOS services are available Return: CF clear if successful CF set on error AX = error code Note: new handler must chain to previous handler as its first action SeeAlso: AX=5FE0h --------N-215FE2----------------------------- INT 21 - LANtastic - GET MESSAGE SERVICE VECTOR AX = 5FE2h Return: CF clear if successful ES:BX -> current FAR message service routine CF set on error AX = error code SeeAlso: AX=5FE0h,AX=5FE3h --------N-215FE3----------------------------- INT 21 - LANtastic - SET MESSAGE SERVICE VECTOR AX = 5FE3h ES:BX -> FAR routine for processing network messages Return: CF clear if successful CF set on error AX = error code Notes: handler must chain to previous handler as its first action on invocation, ES:BX -> just-received message SeeAlso: AX=5FE2h --------!---Section--------------------------