home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Chip 1997 April
/
Chip_1997-04_cd.bin
/
ovladace
/
novell
/
dwenu_n2
/
dwenu_n2.exe
/
LANDRV32
/
SKTOKNW.LDI
< prev
next >
Wrap
Text File
|
1996-07-04
|
18KB
|
422 lines
;DrIvEr DeScRiPtIoN
;CoPyRiGhT=(C)Copyright 1993-1996 SysKonnect. All rights reserved
VER: 1.07
SyntaxVersion: 1.00
Driver SKTOKNW_ISA
{
Description: $SKTOKNW_ISA_DES
Help: $SKTOKNW_HLP
Par: 1.00
File: SKTOKNW.LAN
Timeout: 40
PROMPT PORT1 REQUIRED
{
Description: $PORT_ISA_DES
Help: $PORT_ISA_HLP
Type: HEX(4)
Values: 0A20, 1A20, 0B20, 1B20, 1980, 0980, 1900, 0900
Default: 0A20
OutputFormat: 'PORT=%s'
ReservedLength: 32
}
PROMPT INT REQUIRED
{
Description: $INT_ISA_DES
Help: $INT_ISA_HLP
Type: HEX(1)
Values: 3, 5, 9, A, B, C, F
Default: 3
OutputFormat: 'INT=%s'
}
PROMPT DMA REQUIRED
{
Description: $DMA_ISA_DES
Help: $DMA_ISA_HLP
Type: DECIMAL(1)
Values: 5, 6, 7
Default: 5
OutputFormat: 'DMA=%s'
}
PROMPT NODE OPTIONAL
{
Description: $NODE_DES
Help: $NODE_HLP
}
FRAME FrameSelect OPTIONAL
{
CDescription: "TOKEN-RING"
Choice: 'Token-Ring'
CDescription: "TOKEN-RING_SNAP"
Choice: 'Token-Ring_SNAP'
Default: 1,2
OctetBitOrder: MSB
}
PROMPT SPEED REQUIRED
{
Description: $RATE_DES
Help: $RATE_HLP
Type: DECIMAL(2)
Values: 16,4
Default: 16
OutputFormat: 'SPEED=%s CARDTYPE=1'
}
LIST MPR OPTIONAL
{
Description: $MPR_DES
Help: $MPR_HLP
CDescription: $MPR_CDES1
Choice: ''
CDescription: $MPR_CDES2
Choice: 'MPR'
Default: 1
OutputFormat: '%s'
}
LIST SERVMEM if (GT_16 == TRUE) REQUIRED
else OPTIONAL
{
Description: $M16_DES
Help: $M16_HLP
CDescription: $M16_CDES1
Choice: ''
CDescription: $M16_CDES2
Choice: 'BELOW16'
Default: 1
OutputFormat: '%s'
}
LIST QUIET OPTIONAL
{
Description: $QUIET_DES
Help: $QUIET_HLP
CDescription: $QUIET_CDES1
Choice: ''
CDescription: $QUIET_CDES2
Choice: 'QUIET'
Default: 2
OutputFormat: '%s'
}
}
DLANG: 4
;Default: English
$SKTOKNW_ISA_DES = "SK-NET Token-Ring ISA"
$SKTOKNW_HLP = "This server driver supports the SK-NET TR4
, SK-NET TR16 , SK-NET TR4/16
, and SK-NET TR4/16+"
$PORT_ISA_DES = "I/O port address"
$PORT_ISA_HLP = "The port address must match the DIP switch
settings on the board."
$INT_ISA_DES = "Interrupt Level"
$INT_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$DMA_ISA_DES = "DMA Channel"
$DMA_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$NODE_DES = "Node Address"
$NODE_HLP = "This parameter sets the locally administered
address for the Token-Ring adapter. This
address must be unique on the ring and ranges
from 400000000000 to 7FFFFFFFFFFF. All 12
digits must be entered!
Do not change this address unless you are
prepared to administer local addresses
according to IEEE 802.2 specifications. Be
careful not to enter a node address that is
already in use by another station."
$RATE_DES = "Data Rate"
$RATE_HLP = "NOTE: selection of the wrong data rate may cause
tremendous ring stress!"
$MPR_DES = "MPR Source Route Support"
$MPR_HLP = "Select this option, if a
Multiprotocol-Router (MPR) is installed on your
system, and if it is configured as a Source Route
bridge."
$MPR_CDES1 = "No Source Route MPR"
$MPR_CDES2 = "MPR Source Route Bridge Support"
$M16_DES = "Server Memory"
$M16_HLP = "If your server has more than 16 MB memory, the BELOW16
commandline parameter is required for proper operation
of the SK-NET Token-Ring ISA adapter!\n
NOTE: Memory above 16MB must not be registered before
the LAN driver is loaded!"
$M16_CDES1 = "Less than 16 MB server memory"
$M16_CDES2 = "More than 16 MB server memory"
$QUIET_DES = "Quiet Mode"
$QUIET_HLP = "Select this option if you want to suppress
driver status messages.\n
NOTE: Usage of this parameter is highly recommended
for Client32!"
$QUIET_CDES1 = "Status messages enabled"
$QUIET_CDES2 = "Status messages disabled"
LANG: 6
;French
$SKTOKNW_ISA_DES = "SK-NET Token-Ring ISA"
$SKTOKNW_HLP = "This server driver supports the SK-NET TR4
, SK-NET TR16 , SK-NET TR4/16
, and SK-NET TR4/16+"
$PORT_ISA_DES = "I/O port address"
$PORT_ISA_HLP = "The port address must match the DIP switch
settings on the board."
$INT_ISA_DES = "Interrupt Level"
$INT_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$DMA_ISA_DES = "DMA Channel"
$DMA_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$NODE_DES = "Node Address"
$NODE_HLP = "This parameter sets the locally administered
address for the Token-Ring adapter. This
address must be unique on the ring and ranges
from 400000000000 to 7FFFFFFFFFFF. All 12
digits must be entered!
Do not change this address unless you are
prepared to administer local addresses
according to IEEE 802.2 specifications. Be
careful not to enter a node address that is
already in use by another station."
$RATE_DES = "Data Rate"
$RATE_HLP = "NOTE: selection of the wrong data rate may cause
tremendous ring stress!"
$MPR_DES = "MPR Source Route Support"
$MPR_HLP = "Select this option, if a
Multiprotocol-Router (MPR) is installed on your
system, and if it is configured as a Source Route
bridge."
$MPR_CDES1 = "No Source Route MPR"
$MPR_CDES2 = "MPR Source Route Bridge Support"
$M16_DES = "Server Memory"
$M16_HLP = "If your server has more than 16 MB memory, the BELOW16
commandline parameter is required for proper operation
of the SK-NET Token-Ring ISA adapter!\n
NOTE: Memory above 16MB must not be registered before
the LAN driver is loaded!"
$M16_CDES1 = "Less than 16 MB server memory"
$M16_CDES2 = "More than 16 MB server memory"
$QUIET_DES = "Quiet Mode"
$QUIET_HLP = "Select this option if you want to suppress
driver status messages.\n
NOTE: Usage of this parameter is highly recommended
for Client32!"
$QUIET_CDES1 = "Status messages enabled"
$QUIET_CDES2 = "Status messages disabled"
LANG: 7
;German
$SKTOKNW_ISA_DES = "SK-NET Token-Ring ISA"
$SKTOKNW_HLP = "This server driver supports the SK-NET TR4
, SK-NET TR16 , SK-NET TR4/16
, and SK-NET TR4/16+"
$PORT_ISA_DES = "I/O port address"
$PORT_ISA_HLP = "The port address must match the DIP switch
settings on the board."
$INT_ISA_DES = "Interrupt Level"
$INT_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$DMA_ISA_DES = "DMA Channel"
$DMA_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$NODE_DES = "Node Address"
$NODE_HLP = "This parameter sets the locally administered
address for the Token-Ring adapter. This
address must be unique on the ring and ranges
from 400000000000 to 7FFFFFFFFFFF. All 12
digits must be entered!
Do not change this address unless you are
prepared to administer local addresses
according to IEEE 802.2 specifications. Be
careful not to enter a node address that is
already in use by another station."
$RATE_DES = "Data Rate"
$RATE_HLP = "NOTE: selection of the wrong data rate may cause
tremendous ring stress!"
$MPR_DES = "MPR Source Route Support"
$MPR_HLP = "Select this option, if a
Multiprotocol-Router (MPR) is installed on your
system, and if it is configured as a Source Route
bridge."
$MPR_CDES1 = "No Source Route MPR"
$MPR_CDES2 = "MPR Source Route Bridge Support"
$M16_DES = "Server Memory"
$M16_HLP = "If your server has more than 16 MB memory, the BELOW16
commandline parameter is required for proper operation
of the SK-NET Token-Ring ISA adapter!\n
NOTE: Memory above 16MB must not be registered before
the LAN driver is loaded!"
$M16_CDES1 = "Less than 16 MB server memory"
$M16_CDES2 = "More than 16 MB server memory"
$QUIET_DES = "Quiet Mode"
$QUIET_HLP = "Select this option if you want to suppress
driver status messages.\n
NOTE: Usage of this parameter is highly recommended
for Client32!"
$QUIET_CDES1 = "Status messages enabled"
$QUIET_CDES2 = "Status messages disabled"
LANG: 8
;Italian
$SKTOKNW_ISA_DES = "SK-NET Token-Ring ISA"
$SKTOKNW_HLP = "This server driver supports the SK-NET TR4
, SK-NET TR16 , SK-NET TR4/16
, and SK-NET TR4/16+"
$PORT_ISA_DES = "I/O port address"
$PORT_ISA_HLP = "The port address must match the DIP switch
settings on the board."
$INT_ISA_DES = "Interrupt Level"
$INT_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$DMA_ISA_DES = "DMA Channel"
$DMA_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$NODE_DES = "Node Address"
$NODE_HLP = "This parameter sets the locally administered
address for the Token-Ring adapter. This
address must be unique on the ring and ranges
from 400000000000 to 7FFFFFFFFFFF. All 12
digits must be entered!
Do not change this address unless you are
prepared to administer local addresses
according to IEEE 802.2 specifications. Be
careful not to enter a node address that is
already in use by another station."
$RATE_DES = "Data Rate"
$RATE_HLP = "NOTE: selection of the wrong data rate may cause
tremendous ring stress!"
$MPR_DES = "MPR Source Route Support"
$MPR_HLP = "Select this option, if a
Multiprotocol-Router (MPR) is installed on your
system, and if it is configured as a Source Route
bridge."
$MPR_CDES1 = "No Source Route MPR"
$MPR_CDES2 = "MPR Source Route Bridge Support"
$M16_DES = "Server Memory"
$M16_HLP = "If your server has more than 16 MB memory, the BELOW16
commandline parameter is required for proper operation
of the SK-NET Token-Ring ISA adapter!\n
NOTE: Memory above 16MB must not be registered before
the LAN driver is loaded!"
$M16_CDES1 = "Less than 16 MB server memory"
$M16_CDES2 = "More than 16 MB server memory"
$QUIET_DES = "Quiet Mode"
$QUIET_HLP = "Select this option if you want to suppress
driver status messages.\n
NOTE: Usage of this parameter is highly recommended
for Client32!"
$QUIET_CDES1 = "Status messages enabled"
$QUIET_CDES2 = "Status messages disabled"
LANG: 14
;Spanish
$SKTOKNW_ISA_DES = "SK-NET Token-Ring ISA"
$SKTOKNW_HLP = "This server driver supports the SK-NET TR4
, SK-NET TR16 , SK-NET TR4/16
, and SK-NET TR4/16+"
$PORT_ISA_DES = "I/O port address"
$PORT_ISA_HLP = "The port address must match the DIP switch
settings on the board."
$INT_ISA_DES = "Interrupt Level"
$INT_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$DMA_ISA_DES = "DMA Channel"
$DMA_ISA_HLP = "No DIP switch settings are required because the
driver automatically performs board
configuration."
$NODE_DES = "Node Address"
$NODE_HLP = "This parameter sets the locally administered
address for the Token-Ring adapter. This
address must be unique on the ring and ranges
from 400000000000 to 7FFFFFFFFFFF. All 12
digits must be entered!
Do not change this address unless you are
prepared to administer local addresses
according to IEEE 802.2 specifications. Be
careful not to enter a node address that is
already in use by another station."
$RATE_DES = "Data Rate"
$RATE_HLP = "NOTE: selection of the wrong data rate may cause
tremendous ring stress!"
$MPR_DES = "MPR Source Route Support"
$MPR_HLP = "Select this option, if a
Multiprotocol-Router (MPR) is installed on your
system, and if it is configured as a Source Route
bridge."
$MPR_CDES1 = "No Source Route MPR"
$MPR_CDES2 = "MPR Source Route Bridge Support"
$M16_DES = "Server Memory"
$M16_HLP = "If your server has more than 16 MB memory, the BELOW16
commandline parameter is required for proper operation
of the SK-NET Token-Ring ISA adapter!\n
NOTE: Memory above 16MB must not be registered before
the LAN driver is loaded!"
$M16_CDES1 = "Less than 16 MB server memory"
$M16_CDES2 = "More than 16 MB server memory"
$QUIET_DES = "Quiet Mode"
$QUIET_HLP = "Select this option if you want to suppress
driver status messages.\n
NOTE: Usage of this parameter is highly recommended
for Client32!"
$QUIET_CDES1 = "Status messages enabled"
$QUIET_CDES2 = "Status messages disabled"
;DrIvEr DeScRiPtIoN EnD
