home *** CD-ROM | disk | FTP | other *** search
- # QPV/386 configuration file
- # for SVGAs equipped with an NCR 77C22 chipset (+ optional hicolor DAC)
- #
- # Note: Depending on your BIOS version it may be necessary to load
- # a special driver (SETMODE.SYS) in order to be able to use this
- # configuration.
-
- NCR BGR
- #'NCR 77C22
- #"NCR 77C22 graphics cards with hicolor DAC
-
- # These are the standard VGA modes
- 320 200 16 40 $0d 0
- 640 480 16 80 $12 0
- 320 200 256 320 $13 0
-
- # 16 color SVGA modes:
- 800 600 16 100 $58 0
- 1024 768 16 128 $5b 0 # (interlaced)
- # 1024 768 16 128 $5d 0 # (non-interlaced)
- 1280 1024 16 160 $67 0 # (interlaced)
- # Note: some cards and/or monitors do not support the 1280x1024 resolution.
- # If this is true for you, delete the corresponding line in order to prevent
- # QPV/386 from using that mode.
-
- # 256 color SVGA modes:
- 640 480 256 640 $5f 0
- 800 600 256 800 $5c 0
- 1024 768 256 1024 $61 0 # NCR 77C22E only! (interlaced)
- # 1024 768 256 1024 $62 0 # NCR 77C22E only! (non-interlaced)
- 1280 1024 256 1280 $6a 0 # NCR 77C22E only! (interlaced)
- # 1280 960 256 1280 $6b 0 # NCR 77C22E only! (non-interlaced)
- # Some cards and/or monitors do not support the 1280x1024/960 resolution.
- # Note: Be sure that your SVGA card has enough video memory to display all of
- # these modes. Otherwise delete the corresponding lines in order to prevent
- # QPV/386 from using those modes not supported by your card.
-
- # 32K color (hicolor) modes.
- # Delete them if you don't have a hicolor or truecolor DAC.
- 640 480 32k 1280 $70 0 # NCR 77C22E only!
- 800 600 32k 1600 $71 0 # NCR 77C22E only!
-
- # 64K color (hicolor) modes.
- # If your DAC is capable of 64K color modes, you may uncomment the
- # following lines (remove the '#' characters).
- # 640 480 64k 1280 $78 0 # NCR 77C22E only!
- # 800 600 64k 1600 $79 0 # NCR 77C22E only!
-
- # NOTE:
- # You probably need to setup some modes with softmode.sys (at least for
- # the HiColor modes).
- # Use setmode to adjust these values or do it by hand.
- # However, if you use softmode.sys to adjust one SGVA mode,
- # you must adjust them all !
- #
- # In your config.sys will show up (if you use setmode) something like this.
- # (100 & 102 are for the 32k Hicolor modes)
- #
- # DEVICE=C:\NCR\softmode.sys /m:7,5,3,4,10,0,2,100,102
- #
- # change path C:\NCR to your own needs
-