Turbo Toolbox

home *** CD-ROM | disk | FTP | other *** search

/ Turbo Toolbox / Turbo_Toolbox.iso / os2cd / cdlist.txt next >

Wrap

Text File | 1994-03-02 | 34.8 KB | 850 lines

------------------------------------------------------------------ 2/22/94 OS/2 2.1 CD-ROM DRIVE COMPATIBILITY LIST ---------------------------------------- Note: In addition to any device drivers listed under the column "Drivers" in the table below, all CD-ROM drives require the OS2CDROM.DMD device driver. ------------------------------------------------------------------------------ | Vendor | Model | Interface | Drivers | Available |Notes| |--------------|------------|---------------|--------------|-----------|-----| | BSR | 6800MX | Mitsumi LU002 | MITFX001.ADD | OS/2 2.11 | 1 | |----------------------------------------------------------------------------| | CD Technology| T3301 | SCSI-2 | | OS/2 2.1 | | | | T3401 | SCSI-2 | | OS/2 2.1 | 3 | |----------------------------------------------------------------------------| | Chinon | 431 | SCSI-1 | CHINCDS1.FLT | OS/2 2.11 | 4 | | | 435 | SCSI-1 | CHINCDS1.FLT | OS/2 2.11 | 4 | | | 535 | SCSI-1 | CHINCDS1.FLT | OS/2 2.11 | 4 | |----------------------------------------------------------------------------| | Creative Labs| OmniCD | Panasonic 562 | SBCD2.ADD | OS/2 2.11 | 1 | |----------------------------------------------------------------------------| | Hitachi | CDR-1650S | SCSI-1 | HITCDS1.FLT | OS/2 2.1 | | | | CDR-1700S | Hitachi | HITCDISA.ADD | Hitachi | 5 | | | CDR-1900S | Hitachi | HITCDISA.ADD | Hitachi | 5 | | | CDR-1950S | SCSI-2 | | OS/2 2.1 | 3 | | | CDR-1750S | SCSI-1 | HITCDS1.FLT | OS/2 2.1 | | | | CDR-3600 | Hitachi | HITCDISA.ADD | Hitachi | 5 | | | CDR-3650 | SCSI-1 | HITCDS1.FLT | OS/2 2.1 | | | | CDR-3700 | Hitachi | HITCDISA.ADD | Hitachi | 5 | | | CDR-6700 | Hitachi | HITCDISA.ADD | Hitachi | 5 | | | CDR-3750 | SCSI-2 | | OS/2 2.1 | | | | CDR-6750 | SCSI-2 | | OS/2 2.1 | 3 | |----------------------------------------------------------------------------| | IBM | CD-ROM I | SCSI-1 | TOSHCDS1.FLT | OS/2 2.1 | | | | CD-ROM II | SCSI-2 | | OS/2 2.1 | | | | Enhanced II| SCSI-2 | | OS/2 2.1 | 3 | | | ISA CD-ROM | Panasonic 563 | SBCD2.ADD | OS/2 2.11 | 1 | |----------------------------------------------------------------------------| | Mitsumi | CRMC-LU002 | Mitsumi | MITFX001.ADD | OS/2 2.11 | 1 | | | CRMC-LU005 | Mitsumi | MITFX001.ADD | OS/2 2.11 | 1 | | | CRMC-FX001 | Mitsumi | MITFX001.ADD | OS/2 2.11 | 1 | | | CRMC-FX001D| Mitsumi | MITFX001.ADD | OS/2 2.11 | 1 | |----------------------------------------------------------------------------| | NEC | CDR-25 | SCSI-1 | NECCDS1.FLT | OS/2 2.1 | | | | CDR-36 | SCSI-1 | NECCDS1.FLT | OS/2 2.1 | | | | CDR-37 | SCSI-1 | NECCDS1.FLT | OS/2 2.1 | | | | CDR-38 | SCSI-2 | | OS/2 2.1 | | | | CDR-72 | SCSI-1 | NECCDS1.FLT | OS/2 2.1 | | | | CDR-73 | SCSI-1 | NECCDS1.FLT | OS/2 2.1 | | | | CDR-74 | SCSI-1 | NECCDS1.FLT | OS/2 2.1 | | | | CDR-74-1 | SCSI-2 | | OS/2 2.1 | | | | CDR-82 | SCSI-1 | NECCDS1.FLT | OS/2 2.1 | | | | CDR-83 | SCSI-1 | NECCDS1.FLT | OS/2 2.1 | | | | CDR-84 | SCSI-1 | NECCDS1.FLT | OS/2 2.1 | | | | CDR-84-1 | SCSI-2 | | OS/2 2.1 | | | | 3Xe | SCSI-2 | | OS/2 2.1 | 3,6 | | | 3Xi | SCSI-2 | | OS/2 2.1 | 3,6 | | | 3Xp | SCSI-2 | | OS/2 2.1 | 3,6 | |----------------------------------------------------------------------------| | Panasonic | CR-501 | SCSI-2 | | OS/2 2.1 | | | (Matsushita) | LK-MC501S | SCSI-2 | | OS/2 2.1 | | | | CR-521 | Panasonic | SBCD2.ADD | OS/2 2.11 | 1 | | | CR-522 | Panasonic | SBCD2.ADD | OS/2 2.11 | 1 | | | CR-523 | Panasonic | SBCD2.ADD | OS/2 2.11 | 1 | | | CR-562 | Panasonic | SBCD2.ADD | OS/2 2.11 | 1 | | | CR-563 | Panasonic | SBCD2.ADD | OS/2 2.11 | 1 | |----------------------------------------------------------------------------| | Philips LMS | CM205 | Philips | LMS205.ADD | BBS | 2 | | (LMSI) | CM205 MS | Philips | LMS206.ADD | BBS | 2 | | | CM206 | Philips | LMS206.ADD | BBS | 2 | | | CM225 | Philips | LMS205.ADD | BBS | 2 | | | CM225 MS | Philips | LMS206.ADD | BBS | 2 | | | CM226 | Philips | LMS206.ADD | BBS | 2 | | | CM215 | SCSI-2 | | OS/2 2.1 | 3 | |----------------------------------------------------------------------------| | Pioneer | DRM-600 | SCSI-1 | | OS/2 2.1 | | | | DRM-604X | SCSI-2 | | OS/2 2.1 | | |----------------------------------------------------------------------------| | Procom | PiCD650S | Sony 535 | SONY535.ADD | BBS | 2,7 | | (see notes) | PxCD650S | Sony 535 | SONY535.ADD | BBS | 2,7 | | | PiCDS | Sony 31A | SONY31A.ADD | OS/2 2.11 | 1,7 | | | PxCDS | Sony 31A | SONY31A.ADD | OS/2 2.11 | 1,7 | | | PiCDS-DS | Sony 33A | SONY31A.ADD | OS/2 2.11 | 1,7 | | | PxCDS-DS | Sony 33A | SONY31A.ADD | OS/2 2.11 | 1,7 | | | PiCDM | Mitsumi LU005 | MITFX001.ADD | OS/2 2.11 | 1 | | | SiCD-DS | SCSI-2 | | OS/2 2.1 | 8 | | | MCD-DS | SCSI-2 | | OS/2 2.1 | 8 | | | SiCDN-3x | SCSI-2 | | OS/2 2.1 | 8 | | | MCDN-3x | SCSI-2 | | OS/2 2.1 | 8 | |----------------------------------------------------------------------------| | Sony | CDU-31A | Sony | SONY31A.ADD | OS/2 2.11 | 1 | | | CDU-33A | Sony | SONY31A.ADD | OS/2 2.11 | 1 | | | CDU-531 | Sony | SONY535.ADD | BBS | 2 | | | CDU-535 | Sony | SONY535.ADD | BBS | 2 | | | CDU-541 | SCSI-2 | | OS/2 2.1 | | | | CDU-561 | SCSI-2 | | OS/2 2.1 | | | | CDU-6201 | Sony | SONY535.ADD | BBS | 2 | | | CDU-6205 | Sony | SONY535.ADD | BBS | 2 | | | CDU-6111 | SCSI-1 | SONYCDS1.FLT | OS/2 2.1 | | | | CDU-6211 | SCSI-2 | | OS/2 2.1 | | | | CDU-7201 | Sony | SONY535.ADD | BBS | 2 | | | CDU-7205 | Sony | SONY535.ADD | BBS | 2 | | | CDU-7211 | SCSI-2 | | OS/2 2.1 | | | | CDU-7305 | Sony | SONY31A.ADD | OS/2 2.11 | 1 | | | CDU-7405 | Sony | SONY31A.ADD | OS/2 2.11 | 1 | | | CDU-7811 | SCSI-2 | | OS/2 2.1 | 3 | |----------------------------------------------------------------------------| | Tandy | CDR-1000 | Mitsumi LU002 | MITFX001.ADD | OS/2 2.11 | | |----------------------------------------------------------------------------| | Texel | DM-3021 | SCSI-1 | SONYCDS1.FLT | OS/2 2.1 | | | (Plextor) | DM-3024 | SCSI-2 | | OS/2 2.1 | | | | DM-3028 | SCSI-2 | | OS/2 2.1 | 3 | | | DM-5021 | SCSI-1 | SONYCDS1.FLT | OS/2 2.1 | | | | DM-5024 | SCSI-2 | | OS/2 2.1 | | | | DM-5028 | SCSI-2 | | OS/2 2.1 | 3 | |----------------------------------------------------------------------------| | Toshiba | XM-3201 | SCSI-1 | TOSHCDS1.FLT | OS/2 2.1 | | | | XM-3301 | SCSI-2 | | OS/2 2.1 | | | | XM-3401 | SCSI-2 | | OS/2 2.1 | | | | XM-4101 | SCSI-2 | | OS/2 2.1 | 3 | ------------------------------------------------------------------------------ Notes: 1. The non-SCSI CD-ROM drivers included in OS/2 2.11 are also available from the OS2SUPPORT forum on CompuServe, Prodigy and other IBM BBS'es. BBS Zip File | Driver -------------|----------------------- MITFX.ZIP | contains MITFX001.ADD SBCD2.ZIP | contains SBCD2.ADD SONY31.ZIP | contains SONY31A.ADD CHINON.ZIP | contains CHINCDS1.FLT 2. The Sony 535 and Philips LMS drivers are in beta test and are available from PSPBETA forum on CompuServe, Prodigy, and other IBM BBS'es. BBS Zip File | Driver -------------|----------------------- SONY53.ZIP | contains SONY535.ADD LMS205.ZIP | contains LMS205.ADD LMS206.ZIP | contains LMS206.ADD 3. The SCSI CD-ROM drive was announced after OS/2 2.1 shipped and has subsequently been certified to work with OS/2 2.1. The CD-ROM drive model does not appear in the OS/2 2.1 Selective Install list, but is supported with the existing device drivers which ship in OS/2 2.1. The following table lists the new CD-ROM drive model along with the entry which should be selected in the Selective Install list to install the correct CD-ROM driver. (Note: The new entries have been added to the Selective Install list in OS/2 2.11). Post 2.1 Certified SCSI CD-ROM | OS/2 2.1 Selective Install Choice --------------------------------------------------------------------- CD Technology T3401 | CD Technology T3301 Hitachi CDR-1950S, 6750 | Hitachi CDR-3750 IBM Enhanced CD-ROM II | IBM CD-ROM II NEC MultiSpin 3Xe,3Xi,3Xp | NEC MultiSpin 38,74,84 Philips LMS CM215 | Other Sony CDU-7811 | Sony CDU-541,561,6211,7211 Texel DM-3028,5028 | Texel DM-3024,5024 Toshiba XM-4101 | Toshiba 3301,3401 4. The Chinon CD-ROM drive must be attached to a SCSI adapter which is supported in OS/2 with an OS/2 SCSI Adapter Device Driver (.ADD). There is currently no support for the Chinon SCSI adapter which is typically bundled with the drive. Chinon is developing an OS/2 Adapter Device Driver for their SCSI card, but no date has been committed. 5. The Hitachi non-SCSI CD-ROM device drivers are available from Hitachi. IBM does not provide support for these drives. 6. Kodak multisession photo CD support for the NEC 3X drives requires the OS2CDROM.DMD driver which ships in OS/2 2.11 (or OS/2 2.1 Service Pack). Single session photo CD for the NEC 3X is supported with the OS2CDROM.DMD which ships in OS/2 2.1. 7. The non-SCSI host adapters manufactured by Procom are based on Sony's host adapter design and are supposedly compatible with the standard Sony host adapters which OS/2 supports. IBM has not certified the Procom adapters as yet, however. 8. The Procom SCSI CD-ROM drive must be attached to a SCSI adapter which is supported in OS/2 with an OS/2 SCSI Adapter Device Driver (.ADD). There is currently no support for the Procom SCSI adapter which is typically bundled with the drive. ============================================================================ CD-ROM ORIGINAL EQUIPMENT MANUFACTURERS (OEMs) ----------------------------------------------- The table below lists the currently known Original Equipment Manufacturers (OEMs) of CD-ROM drives. All other vendors are resellers of drives from these OEMs. -------------------------------------------------------------------------- | OEM | OS/2 Support | |------------------------------------------------------------------------| | Chinon | Yes - see compatibility table above | |------------------------------------------------------------------------| | Goldstar | Non-SCSI driver in development by Goldstar | |------------------------------------------------------------------------| | Hitachi | Yes - see compatibility table above | |------------------------------------------------------------------------| | Mitsumi | Yes - see compatibility table above | |------------------------------------------------------------------------| | NEC | Yes - see compatibility table above | |------------------------------------------------------------------------| | Panasonic (Matsushita) | Yes - see compatibility table above | |------------------------------------------------------------------------| | Philips LMS | Yes - see compatibility table above | |------------------------------------------------------------------------| | Pioneer | Yes - see compatibility table above | |------------------------------------------------------------------------| | Plextor (Texel) | Yes - see compatibility table above | |------------------------------------------------------------------------| | Sony | Yes - see compatibility table above | |------------------------------------------------------------------------| | Teac | SCSI-2 drives should work, but not certified | |------------------------------------------------------------------------| | Toshiba | Yes - see compatibility table above | |------------------------------------------------------------------------| | Wearnes | No | -------------------------------------------------------------------------- ============================================================================ SUPPORTED AUDIO CARD/CD-ROM PORT COMBINATIONS --------------------------------------------- The following table lists the Media Vision and Creative Labs audio cards which contain a CD-ROM port which is supported in OS/2 2.11. Audio cards with CD-ROM ports from other manufacturers should also work if they provide a compatible CD-ROM interface chip. Media Vision ------------ ProAudio Spectrum 16 with Trantor SCSI port (TMV1SCSI.ADD) ProAudio Spectrum 16 with Sony31A/Sony33A CD-ROM port (SONY31A.ADD) ProAudio Spectrum 16 with Philips LMS CM205 CD-ROM port (LMS205.ADD) ProAudio Spectrum 16 with Philips LMS CM206 CD-ROM port (LMS206.ADD) Jazz 16 with Future Domain FD9C50 SCSI port (FD8XX.ADD) Jazz 16 with Panasonic 563 CD-ROM port (SBCD2.ADD) Jazz 16 with Philips CM206 CD-ROM port (LMS206.ADD) Creative Labs ------------- Sound Blaster Pro with Panasonic CD-ROM port (SBCD2.ADD) Sound Blaster 16 with Panasonic CD-ROM port (SBCD2.ADD) Sound Blaster 16 SCSI-2 with Adaptec SCSI port (AHA152X.ADD) Sound Blaster 16 MultiCD with Mitsumi, (MITFX001.ADD, Sony and, SONY31A.ADD, Panasonic CD-ROM ports SBCD2.ADD) ============================================================================ ------------------------------------ | Mitsumi Device Driver Parameters | ------------------------------------ The parameters for the following CD-ROM adapter device drivers are described in this section: MITFX001.ADD This device driver supports the following CD-ROM drives: Mitsumi CRMC-FX001D Mitsumi CRMC-FX001 Mitsumi CRMC-LU005S Mitsumi CRMC-LU002S BSR 6800 Tandy CDR-1000 This section lists the parameters which are supported for the Mitsumi CD-ROM device driver. The parameters can be changed by modifying the BASEDEV=MITFX001.ADD line in config.sys. It is recommended to change the transfer mode from it default, software polling transfer, to software interrupt transfer. This will help lower the CPU utilization of CD-ROM applications, enabling better performance for other tasks while the CD-ROM drive is being accessed. See the /I parameter below. For the MITFX001.ADD device driver, the syntax for the line in config.sys is as follows: BASEDEV=MITFX001.ADD [/P:nnn] [I:nn] [/V] [/P:nnn] Specifies the base I/O port address of the interface card. This must be the same number as specified by the DIP switch on the interface card. [/I:nn] Specifies the interrupt request (IRQ) channel number. This must match the value specified on the jumper setting on the interface card. If this parameter is not specified, the device driver will use software polling transfer. [/V] The device driver will display the device driver revision level and CD-ROM product information at boot time. Mitsumi CD-ROM Device Driver Parameter Examples ----------------------------------------------- 1. Mitsumi CD-ROM drive attached to Mitsumi host adapter: If the Mitsumi host adapter is set to a base I/O port address of 320, the line in config.sys should be: BASEDEV=MITFX001.ADD /P:320 2. Mitsumi CD-ROM drive attached to Creative Labs Sound Blaster 16 MultiCD If the Mitsumi CD-ROM port on the Sound Blaster 16 MultiCD is set to I/O port address of 340, the line in config.sys should be: BASEDEV=MITFX001.ADD /P:340 3. To enable interrupt transfer mode, which improves performance, the /I parameter must be specified. For example to enable interrupt transfer mode for IRQ channel 10 at I/O port address of 320h, the line in config.sys should appear as follows: BASEDEV=MITFX001.ADD /P:320 /I:10 Known Problems -------------- The Diamond Viper video card and the Mitsumi host adapter conflict at port address 300h, which is the default port address of the Mitsumi card. The result is a messed up display screen. The user should change the port address on the Mitsumi card from 300h to another address, i.e. 310h, and add the /P parm to the BASEDEV=MITFX001.ADD statement in config.sys. ------------------------------------- | Sony 31A Device Driver Parameters | ------------------------------------- The parameters for the following CD-ROM adapter device drivers are described in this section: SONY31A.ADD This device driver supports the following CD-ROM drives: Sony CDU-31A,CDU-7305 Sony CDU-33A,CDU-7405 This section lists the parameters which are supported for the Sony CD-ROM device driver. The parameters can be changed by modifying the BASEDEV=SONY31A.ADD line in config.sys. It is recommended to change the transfer mode from it default, software polling transfer, to software interrupt transfer. This will help lower the CPU utilization of CD-ROM applications, enabling better performance for other tasks while the CD-ROM drive is being accessed. See the /I parameter below. For the SONY31A.ADD device driver, the syntax for the line in config.sys is as follows: BASEDEV=SONY31A.ADD [/A:d] [/AT:dd] [/P:nnn] [I:nn] [/V] [/A:d] Identifies a specific adapter, d. The adapter is specified as a single digit value which is zero based. (i.e. The first adapter is specified as /A:0). [/AT:dd] Sets the adapter type connected to the CD-ROM drive. Supported values are: 00 = Sony CDB-334 (default) 05 = - Echo Speech (with ESC614 chip) - Orchid SoundWave 32 - Orchid GameWave 32 - Cardinal DSP16 08 = Media Vision ProAudio Spectrum-16 [/P:nnnn] Specifies the base I/O port address of the interface card. The port address is specified as a four digit hex value. Leading zeros should be specified. The value must be the same number as the port address selected by the jumper on the host interface card. If this parameter is not specified, the default port address for the host adapter is used. For the Sony CDB-334 host interface card, the default is 0340. For the Media Vision ProAudio Spectrum-16 card the default is 1F88. See the section below titled "Sony CDB-334 Host Adapter Jumper Settings". [/I:nn] Specifies the interrupt request (IRQ) channel number. This must match the value specified on the jumper setting on the interface card. If this parameter is not specified, the device driver will use software polling transfer. See the section below titled "Sony CDB-334 Host Adapter Jumper Settings". This parameter switch is not supported if the CD-ROM drive is attached to the Media Vision ProAudio spectrum. Note: Some Sony CDB-334 host adapter cards did not ship with the plastic jumper switch to select the IRQ channel on the IRQ jumper block. You must obtain and install the plastic jumper switch to enable the IRQ channel. [/V] The device driver will display the device driver revision level and CD-ROM product information at boot time. Sony CDU-31A Device Driver Parameter Examples --------------------------------------------- 1. Sony CDU-31A or CDU-33A CD-ROM drive attached to Sony CDB-334 host adapter: The Sony CDB-334 host adapter supports base I/O port addresses of 320h, 330h, 340h or 360h. If the CDB-334 host adapter is set to any port address other than the default of 340h, the config.sys statement needs to be modified. For example, if the Sony CDB-334 host adapter is set to a base I/O port address of 360, the line in config.sys should be: BASEDEV=SONY31A.ADD /A:0 /P:0360 (Note: The Sony Desktop Library model number CDU-31A-LL/N includes the Sony CDB-334 adapter) 2. Sony CDU-31A or CDU-33A CD-ROM drive attached to Sony CDB-334 host adapter. If the Sony CDU-31A is attached to the Sony CDB-334 host adapter at base I/O port address of 360h, and the driver is operating in interrupt mode at IRQ channel 5, the line in your config.sys should be: BASEDEV=SONY31A.ADD /A:0 /P:0360 /I:5 3. Sony CDU-31A or CDU-33A CD-ROM drive attached to Media Vision ProAudio Spectrum-16 (PAS-16) host adapter: The line in config.sys should appear as follows: BASEDEV=SONY31A.ADD /A:0 /AT:08 (Note: The default port address for the CDU-31A when attached to the PAS-16 card is 1F88. The Sony Desktop Library model numbers CDU-31A-LL/L and CDU-7305 include the PAS-16 adapter). 4. Sony CDU-31A or CDU-33A CD-ROM drive attached to the Creative Labs Sound Blaster Pro, Sound Blaster 16, or Sound Blaster 16 MultiCD host adapter: The port address specified on the BASEDEV statement in config.sys should be 10h above the base I/O port address specified on the adapter card. For example, if the Sound Blaster card is set for a base I/O port address of 220h, the line in config.sys should be: BASEDEV=SONY31A.ADD /A:0 /P:0230 5. Sony CDU-31A or CDU-33A CD-ROM drive attached to the Echo Speech, Orchid SoundWave 32, Orchid GameWave 32, or Cardinal DSP16 host adapter: The line in config.sys should appear as follows: BASEDEV=SONY31A.ADD /A:0 /AT:05 ------------------------------------- | Sony 535 Device Driver Parameters | ------------------------------------- The parameters for the following CD-ROM adapter device drivers are described in this section: SONY535.ADD This device driver supports the following CD-ROM drives: Sony 531 series (CDU-531,6201,6205) Sony 535 series (CDU-535,6205,7205) This section lists the parameters which are supported for the Sony CD-ROM device driver. The parameters can be changed by modifying the BASEDEV=SONY535.ADD line in config.sys. It is recommended to change the transfer mode from it default, software polling transfer, to software interrupt transfer. This will help lower the CPU utilization of CD-ROM applications, enabling better performance for other tasks while the CD-ROM drive is being accessed. See the /I parameter below. For the SONY535.ADD device driver, the syntax for the line in config.sys is as follows: BASEDEV=SONY535.ADD [/P:nnn] [I:nn] [/U:d,d...] [/V] [/P:nnn] Specifies the base I/O port address of the interface card. The value must be the same number as the port address selected by the jumper on the host interface card. [/I:nn] Specifies the interrupt request (IRQ) channel number. This must match the value specified on the jumper setting on the interface card. If this parameter is not specified, the device driver will use software polling transfer. Note: Some Sony host adapter cards did not ship with the plastic jumper switch to select the IRQ channel on the IRQ jumper block. You must obtain and install the plastic jumper switch to enable the IRQ channel. [/U:d,d...] Specifies the drive unit number which the Sony CD-ROM drive is set to. The value of d must be set to 0,1,2 or 3. If more than one Sony CD-ROM drive is attached to the adapter, this parameter must be specified. If only one CD-ROM drive is attached to the adapter, and this parameter is not specified, then the default unit id used by the driver is 0. [/V] The device driver will display the device driver revision level and CD-ROM product information at boot time. Sony CDU-535 Device Driver Parameter Examples --------------------------------------------- 1. Sony CD-ROM drive attached to Sony CDB-240 series host adapter: For example, if the Sony host adapter is set to a base I/O port address of 360, the line in config.sys should be: BASEDEV=SONY535.ADD /P:360 2. Sony CD-ROM drive attached to Sony CDB-240 series host adapter. If the Sony CD-ROM drive is attached to the Sony host adapter at base I/O port address of 360h, and the driver is operating in interrupt mode at IRQ channel 5, the line in your config.sys should be: BASEDEV=SONY535.ADD /P:360 /I:5 3. Multiple Sony CD-ROM drives daisy chained to Sony CDB-240 series host adapter For example, if two Sony CD-ROM drives are daisy chained from the Sony host adapter with the first drive set to drive unit 0 and the second set to drive unit 1, the line in config.sys should appear as follows: BASEDEV=SONY535.ADD /P:340 /U:0,1 -------------------------------------- | SBCD2.ADD Device Driver Parameters | -------------------------------------- The parameters for the following CD-ROM adapter device drivers are described in this section: SBCD2.ADD This device driver supports the following CD-ROM drives: Creative Labs OmniCD IBM ISA CD-ROM Panasonic 521,522,523,562,563 This section lists the parameters which are supported for the SBCD2.ADD device driver. The parameters can be changed by modifying the BASEDEV=SBCD2.ADD line in config.sys. For the SBCD2.ADD device driver, the syntax for the line in config.sys is as follows: BASEDEV=SBCD2.ADD [/P:nnn] [T:n] [/NS] [/V] [/P:nnn] Specifies the base I/O port address of the interface card. The value must be the same number as the port address selected by the jumper on the host interface card. [/T:nn] Sets the adapter type connected to the CD-ROM drive. Supported value is: 2 = Creative Labs CD-ROM interface card (not Sound Blaster) [/NS] Disable drive select scan. Driver will not scan for more than one CD-ROM drive. Parameter Examples ------------------ 1. Panasonic, Creative Labs OmniCD or IBM ISA CD-ROM drive attached to standard Panasonic or IBM ISA CD-ROM host adapter: The standard Panasonic or IBM ISA host adapter supports base I/O port addresses of 300h, 310h, 320h or 330h. For example, if the adapter is set to a base I/O port address of 300, the line in config.sys should be: BASEDEV=SBCD2.ADD /P:300 2. Panasonic, Creative Labs OmniCD or IBM ISA CD-ROM drive attached to Creative Labs Sound Blaster Pro, Sound Blaster 16, or Sound Blaster 16 MultiCD. For example, if the Sound Blaster card is set for a base I/O address of 220h, the line in config.sys should be: BASEDEV=SBCD2.ADD /P:220 3. Creative Labs OmniCD attached to standard Creative Labs CD-ROM host adapter (not Sound Blaster) : The standard Creative Labs host adapter supports base I/O port addresses of 250h or 260h. For example, if the adapter is set to a base I/O port address of 250, the line in config.sys should be: BASEDEV=SBCD2.ADD /P:250 /T:2 4. Panasonic, Creative Labs OmniCD or IBM ISA CD-ROM drive attached to Media Vision Jazz 16 sound card. For example, if the Media Vision card is set for a base I/O address of 300h, the line in config.sys should be: BASEDEV=SBCD2.ADD /P:300 /NS 5. Panasonic, Creative Labs OmniCD or IBM ISA CD-ROM drive attached to Reveal audio card. For example, if the Reveal audio card is set for a base I/O address of 630h, the line in config.sys should be: BASEDEV=SBCD2.ADD /P:630 -------------------------------------------- | Philips LMS 205 Device Driver Parameters | -------------------------------------------- The parameters for the following CD-ROM adapter device drivers are described in this section: LMS205.ADD This device driver supports the following CD-ROM drives: Philips LMS CM205,CM225 This section lists the parameters which are supported for the Philips LMS 205 CD-ROM device driver. The parameters can be changed by modifying the BASEDEV=LMS205.ADD line in config.sys. For the LMS205.ADD device driver, the syntax for the line in config.sys is as follows: BASEDEV=LMS205.ADD [/P:nnn] [/u:X] [/m:Y] [/V] [/P:nnn] Specifies the base I/O port address of the interface card. The value must be the same number as the port address selected by the jumper on the host interface card. [/u:X] Identifies a specific unit, X. Valid values for X are 0, 1, 2, 3. The default is zero. LMS205 locates all CM250 and CM260 host adapters and assigns unit numbers based on the order in which each was found. This parameter tells LMS205 which BASEDEV=LMS205.ADD line it is currently processing. [/m:Y] Indicates the number of 2500 byte CD frame buffers that should be allocated by the LMS205.ADD driver. Valid values for Y are 8,..., 26. The default is 16. Any value below the minimum (8) will be assigned the minimum (8). [/V] The device driver will display the device driver revision level and CD-ROM product information at boot time. For example, IBM OS/2 LMS205.ADD 1.00 02-NOV-93 Philips LMS Unit 0: CM205 CDROM drive, FR4, CM260 HA Port: 0340 IRQ: 05 -------------------------------------------- | Philips LMS 206 Device Driver Parameters | -------------------------------------------- The parameters for the following CD-ROM adapter device drivers are described in this section: LMS206.ADD This device driver supports the following CD-ROM drives: Philips LMS CM205MS,CM225MS (multisession photo CD version of CM205) Philips LMS CM206,CM226 This section lists the parameters which are supported for the Philips LMS CD-ROM device driver. The parameters can be changed by modifying the BASEDEV=LMS206.ADD line in config.sys. For the LMS206.ADD device driver, the syntax for the line in config.sys is as follows: BASEDEV=LMS206.ADD [/P:nnn] [/u:X] [/m:Y] [/V] [/P:nnn] Specifies the base I/O port address of the interface card. The value must be the same number as the port address selected by the jumper on the host interface card. [/u:] Identifies a specific unit, X. Valid values for X are 0, 1, 2, 3. The default is zero. LMS206 locates all CM250 and CM260 host adapters and assigns unit numbers based on the order in which each was found. This parameter tells LMS206 which BASEDEV=LMS206.ADD line it is currently processing. [/m:] Indicates the number of 2500 byte CD frame buffers that should be allocated by the LMS206.ADD driver. Valid values for Y are 8,..., 26. The default is 16. Any value below the minimum (8) will be assigned the minimum (8). [/v] The device driver will display the device driver revision level and CD-ROM product information at boot time. For example, IBM OS/2 LMS206.ADD 1.00 02-NOV-93 Philips LMS Unit 0: CM206 CDROM drive, FR4, CM260 HA Port: 0340 IRQ: 05