HPAVC/HPAVC CD-ROM.iso/pc/DFA-007.ZIP/README.TXT

Text File | 1997-07-04 | 12.5 KB | 2,049 lines

-┼----[eXTReMe^dƒa]------------------------------------------- - -- -   -
                ^dfa present : ThE BoNG FiLE
-------------------------------------------------------------  --  --  -    -
 Well people, here it is. The bong file - for all you stoners to
use. This file includes many cool bongs, from the triple chamber,
to the ultimate party bong. Next time your looking for an altervative,
try on of these...

MASON JAR BONG -------------- -- -     -

     > _________
    /   -------.|        ____
   mouthpiece  ||        \  / <---- bowl
               ||         ||
               ||         ||
           ____||_________||____
          |____||_________||____|
          |    ||         ||    |
          |    ||         ||    |
  jar --> |               ||    |
          |               ||    |
          |^^^^^^^^^^^^^^^||^^^^| <---- water line
          |               ||    |
          |               ||    |
          |               ||    |
          |               ||    |
          |_____________________|

Classic design, efficient, easy to make and paint. I used surgical
tubing for the mouthpiece and one of the aforementioned toilet tubes for
the bowl and pipes (I cut a piece about two inches off and stuck it
through the lid for the shorter tube, put the tubing over that). The
carb could be placed in the lid if you wish (mine is carbless).

COKE BOTTLE BONG ---------- -- - -   -

This is a simple design, but the most efficient bong I've found. Take a
1-litre plastic bottle and put two holes in it, one about halfway down
the bottle and the other on the opposite side about an inch up from
the bottom. Take a pipe & bowl (toilet tube is perfect, once again) and
insert it in the lower hole. Hold the pipe up at about a 60 degree angle
so that the bottom of the pipe is almost at the bottom of the bottle and
the bowl is sticking up as much as possible, and seal/glue it in place
(I use hot glue for this one and change the bottle about every month,
scraping out the old one for resin, keeping the toilet tube). Fill the
bottle up with water to about halfway between the two holes. You hold
the bottle straight up so that the bowl is pointing up and away from
you. The hole halfway up on the back is your carb, and suck from the
mouthpiece of the bottle. You can also make it out of smaller bottles
for more portability, or link two or more bottles together, or use
bigger bottles for a larger chamber... experiment.

               |   | <--- Mouthpiece
              /     \
  Shotty --> |o      |
             \       / /( <-- bowl     ^^^ -- water level
             /^^^^^^^//
            |      //|
            |    //  |
            |________|


TRIPLE CHAMBER MASON JAR ----------- --- -    --

This is a design that has worked quite well for me as well. The design
is the same as the mason jar bong above, but there are three jars used.
Three wide-mouth mason jars of different sizes are needed. The second
largest jar comes first. Mount the bowl and pipe as above, except
instead of the mouth piece going into your mouth, use a 1/2" diameter
piece of rubbing tubing and put it into the largest jar, below the water
level. Then another half-inch piece from above the water level of the
largest jar into the smallest, below water level, and finally a
mouthpiece from above the water level of the smallest. When you suck on
the tube of the smallest, it lowers the air pressure in the jar, and it
sucks air from the largest chamber. The air pressure in the largest goes
down, so it sucks from the chamber of the second-largest jar, which then
sucks the smoke down from the bowl on that one. This is kind of the
chain:

        Mouth hose (3/8" rubber) - chamber on smallest - 1/2" rubber
        hose below water level on smallest - chamber of largest - below
        water level of largest - chamber of second largest - 3/8" pipe
        below water level of second largest - bowl & choof.

That's as clear as I can make the design... it gives a surprising amount
of suction and absolutely huge tokes. You can work out some kind of
carburation system for it, but it seems to me that carbs are rather
pointless with this design. Make sure all seals between lids of jars and
the hoses are airtight - one small hole will stop it from working.


THE KONG BONG ------- --  -    -

Take a 20 litre plastic water cooler jug. Drill four 3/8" holes around
to the top, put in four 3/8" hoses a couple feet long and seal them. These
are your mouthpieces. Then find a bowl. For the bowl on mine, I use one of
those large spark plug sockets. Drill a hole in the lid of the bottle and
insert the bowl. Seal it with silicone or something similarily
heat-resistant. Then, on the bottom of the cap, afix a rubber hose over
the bottom of the bowl and seal it in place. This is your main bowl
w/hose. Now drill a 1" hole in the side of the bottle right at the
bottom, and put in some kind of plug or pipe with a removable
water-tight cap. Fill the bong half-full of water and put the lid on the
top. You now have a bong with a 10 litre chamber and a bowl that can
hold as much as an eighth of an ounce of choof that four people can suck
on at once. A propane torch or similar heavy-duty flame is recommended
for lighting the bowl, as the bowl is too big for a lighter flame. Once
we're all nicely cooked, I usually re-stuff the bowl and hold a flame to
it while I uncap the hole near the bottom and plug the toke hoses. This
drains all the water out, and as it drains, it serves as a waterfall as
well, fully filling up the 20-litre bottle (with the pipe & hose, the
waterfall smoke is bubbled through the draining water) with smoke. Any
hoses that aren't being used to toke should be plugged (as well, cover the
end with your thumb while exhaling or resting) or there won't be any suction.
Or unplug a couple hoses and they'll serve as a carb to drain the chamber.
The ultimate party bong.

SPRINGER --------- -- -    -

                             <-- Mouthpiece
                        |  |
                        |  |
                        |  |
                        | o| <-- Shotty
           Bowl -->  )\ |  |
                      \\    \
                      |^\\^^^|
                      |______|

The springer, consists of a small glass Spring Valley bottle, with a tall,
cylindrical piece of rubber on the top. The stem passes through the rubber and
into the bottle, and the shotty is placed halfway up the shaft. The rubber can
be found in many bong shops for around 5.00, but if your really desperate, you
can probably use a cardboard roll from a glad wrap package. The rubber can vary
in size, and some springers can have rubber one metre high. This is an excellent
bong, as it is easy to carry around, when you can hold the small bottle and have
the rubber in youre jacket.
---------------------------------------------- -[eXTReMe^dƒa]- --- - -    -