100 Error 100 Null Pointer 101 Error 101 Memory Error 102 Error 102 Invalid Parameter 103 Error 103 Item Not Found 104 Error 104 Null Handle 105 Error 105 No Match 106 Error 106 Buffer Overflow 107 Error 107 Maximun Exceeded 108 Error 108 Return UnInit 109 Error 109 Out Of Memory 110 Error 110 Operation Aborted 500 Error 500 u64 Overflow 501 Error 501 u64 Underflow 502 Error 502 u64 Divide By Zero 600 Error 600 Can't Create MUX Semaphore 601 Error 601 Can't Create Event Semaphore 602 Error 602 Semaphore Set Error 603 Error 603 Semaphore Reset Error 604 Error 604 Semaphore Wait Error 605 Error 605 Semaphore Request Error 606 Error 606 Semaphore Release Error 607 Error 607 Semaphore Wait Abandoned 608 Error 608 Semaphore Wait Timeout 614 , 615 0 616 AM 617 PM 618 : 619 0 620 - 621 Please insert the new media into the drive. 622 Device Type 623 Internal Tape Drive 624 External Tape Drive 625 Data Rate 626 500k 627 1 MBPS 628 2 MBPS 629 Controller (Internal) 630 Controller (External) 631 I/O Address 632 IRQ Level 633 DMA Channel 634 Iomega parallel port 635 Iomega PPT, (MSO) chip 636 Transfer Rate 637 Iomega Ditto Dash 638 Iomega Tape Accelerator 639 FDC, 1.44MB 640 FDC, 2.88MB 641 Original Location 642 Alternate Path 643 TAB next window ARROWS to select ESC to go back RETURN to continue 644 Restore Path 645 Processing File: 646 Files Selected 647 Files Restored 648 Bytes Selected 649 Bytes Restored 650 Percent Complete 651 Restore Progress 652 ESC to quit 653 Auto-Detect 654 The following device(s) were auto-detected: 655 ARROWS to select a device RETURN to continue ESC to quit F10 to manually add an unlisted device 656 Insert Cartridge number %d, and press OK to continue, or Cancel to quit 657 Configuration 658 UP/DOWN selects RETURN to continue ESC to quit F10 Read New Media 659 Overwrite Options 660 RAHS 661 Name 662 Please insert the first media in this set and press enter 663 Please insert the last media in this set and press enter 664 Please insert the next media in this set and press enter 665 Please insert the previous media in this set and press enter 666 Please insert the media %d in this set and press enter 667 Overwrite 668 If Newer 669 Percent Complete 670 Restore in progress 671 Bytes selected 672 Bytes remaining 673 Bytes transfered 674 Items selected 675 Items processed 676 Current file 677 The volume you have selected is password protected. Type the password in the box. 678 Password 679 You have entered an incorrect password. Hit RETRY to try again or CANCEL to quit. 680 Internal Qic 80 Device 681 Internal Qic 3010 Device 682 Internal Qic 3020 Device 683 Internal 2000 Device 685 Internal 2000F Device 686 Internal Ditto Max 687 Internal Device 688 Parallel Qic 80 Device 689 Parallel Qic 3010 Device 690 Parallel Qic 3020 Device 691 Parallel 2000 Device 692 Parallel 2000F Device 693 Parallel Ditto Max 694 Parallel Device 695 1-Step settings were detected. Do you wish to use the 1-Step Interface? 696 Please insert the media named %s 697 There are no volumes on this media. 698 Device of unknown type 699 The restore is complete. 700 Error 700 Can't Create Thread 701 Error 701 Can't Suspend Thread 702 Error 702 Can't Resume Thread 703 Error 703 Can't Set Thread Priority 704 Error 704 Thread Wait Error 705 Error 705 Thread Wait Abandoned 706 Error 706 Thread Wait Timeout 707 Error 707 Thread Threw 800 Error 800 Invalid Sibling Node 801 Error 801 Invalid Path 802 Error 802 Invalid Flag 803 Error 803 Corrupt Tree 804 Error 804 Too Few Root Paths 805 Error 805 Tree Semaphore Create Failed 900 Error 900 File Not Open 901 Error 901 Invalid Order 902 Error 902 Invalid Action 903 Error 903 Buffer To Small 904 Error 904 No More File Data 905 Error 905 Not File Data 906 Error 906 No More XOS Data 907 Error 907 Operating System Not Supported 908 Error 908 Invalid Logical Format Type 909 Error 909 Threshold Reached 910 Error 910 Compression Error 911 Error 911 Invalid Handle 912 Error 912 End Of Media 913 Error 913 Bad Offset 914 Error 914 Logical Format Aborted 915 Error 915 File Found 916 Error 916 Skip File 917 Error 917 Fatal 918 Error 918 File Not Processed 919 Error 919 Rewrite 920 Error 920 Drive Not Ready 1000 Error 1000 File System Deadlock 1001 Error 1001 File Not Created 1002 Error 1002 No More Search Handles 1003 Error 1003 File Lock Failed 1004 Error 1004 File Access Denied 1006 Error 1006 File Locked 1007 Error 1007 File Exists 1008 Error 1008 No File System Space 1009 Error 1009 File Not Found 1010 Error 1010 Operating System Error 1100 Error 1100 Invalid Directory Entry 1101 Error 1101 Invalid Id 1102 Error 1102 Not Last Media 1200 Error 1200 Not First Media 1300 Error 1300 List Empty 1301 Error 1301 Null List Object 1302 Error 1302 List Index Out Of Range 1400 Error 1400 Engine Stack Full 1401 Error 1401 Engine Stack Empty 1410 Error 1410 Engine Queue Full 1411 Error 1411 Engine Queue Empty 1412 Error 1412 Engine Queue Abort 1420 Error 1420 Source Object Aborted 1421 Error 1421 Source Object Fatal 1430 Error 1430 Destination Object Aborted 1431 Error 1431 Destination Object Fatal 1440 Error 1440 Compare Object Aborted 1441 Error 1441 Compare Object Fatal 1450 Error 1450 Engine Fatal 1451 Error 1451 Operation Aborted 1452 Error 1452 Engine Skip 1453 Error 1453 Engine Peof 1600 Error 1600 Open Failed 1601 Error 1601 Close Failed 1602 Error 1602 Media Full 1610 Error 1610 Read At End Of Media 1611 Error 1611 Read At Threshold Reached 1612 Error 1612 Write At End Of Media 1613 Error 1613 Write At Threshold Reached 1615 Error 1615 Write Failed 1621 Error 1621 No More Volumes 1622 Error 1622 Volume Table Full 1625 Error 1625 Release Bad Buffer 1629 Error 1629 Bad Media 1630 Error 1630 Wait Timeout 1631 Error 1631 Unformatted Media 1632 Error 1632 Unsupported Format 1633 Error 1633 Device Close Failed 1634 Error 1634 Device Not Open 1635 Error 1635 Media Not Open 1636 Error 1636 Error Unwind 1637 Error 1637 Maximum Bad Sectors 1638 Error 1638 Zero Value 1639 Error 1639 Read Failed 1640 Error 1640 Format Media Failed 1641 Error 1641 Span 1642 Error 1642 Span Rename 1643 Error 1643 Span Volume Exists 1644 Error 1644 Span Volume Missing 1645 Error 1645 Span Format 1646 Error 1646 Span Erase 1647 Error 1647 Span Check 1648 Error 1648 Span Continue 1649 Error 1649 Span Reformat 1650 Error 1650 Span to a Specific Media 1651 Error 1651 Span to set the Arrays 1652 Error 1652 Span Remove Media 1653 Error 1653 Span Current Media Full 1654 Error 1654 Drive Not Ready 1800 Error 1800 Action Object Invalid Action 1801 Error 1801 Action Not Set 1802 Error 1802 Action Object Volume Not Found 1803 Error 1803 Action Object Incorrect Media 1804 Error 1804 Action Object Incorrect Password 1805 Error 1805 Clear Archive Bit Failed 2100 Error 2100 Tnt Memory Error 2101 Error 2101 Tnt Memory Conversion Error 2200 Error 2200 Parameter Out of Range 2201 Error 2201 No Files 2202 Error 2202 Memory Error 2203 Error 2203 Invalid Parameter 5000 Error 5010: Broken tape detected (based on hole sensor). 5001 Error 5001 Drive Not Ready 5002 Error 5002: Cartridge not present. 5003 Error 5003: Motor speed error. 5004 Error 5004: Motor speed fault. 5005 Error 5005: Cartridge is write protected. 5006 Error 5006: This error code should not be returned by the tape drive unit. 5007 Error 5007: Illegal track address specified for seek. 5008 Error 5008: Illegal command in report subcontext. 5009 Error 5009: Illegal diagnostic mode. 5011 Error 5011: Read gain setting error. 5012 Error 5012: Command received while error status pending. 5013 Error 5013: Command received while new cartridge pending. 5014 Error 5014: Command illegal or undefined in primary mode. 5015 Error 5015: Command illegal or undefined in format mode. 5016 Error 5016: Command illegal or undefined in verify mode. 5017 Error 5017: Logical forward is not at logical BOT in format mode. 5018 Error 5018: Logical end of track. 5019 Error 5019: Command illegal when cartridge not referenced. 5020 Error 5020: Tape drive self diagnostics failed. 5021 Error 5021: Tape drive EEPROM is not initialized. 5022 Error 5022: Tape drive EEPROM is corrupted or a hardware failure has occurred. 5023 Error 5023: Tape motion time-out error. 5024 Error 5024: Tape data segment is too long. 5025 Error 5025: This error code should not have been returned by the tape drive unit. 5026 Error 5026: Power on reset has occurred. 5027 Error 5027: Software reset has occurred. 5028 Error 5028: Tape drive diagnostic mode 1 detected. 5029 Error 5029: Tape drive diagnostic mode 2 detected. 5030 Error 5030: Tape drive received a command during an non-interruptible process. 5031 Error 5031: Tape drive rate selection error. 5032 Error 5032: Illegal command while in high speed mode. 5033 Error 5033: Illegal seek segment. 5105 Error 5105: Ftdvr Off Track 5106 Error 5106: Ftdvr Uninitialized 5107 Error 5107: Ftdvr Formatting Unsupported 5108 Error 5108: Ftdvr Invalid Write Header 5109 Error 5109: Ftdvr Invalid IOCTL 5110 Error 5110: Ftdvr Defective Tape 5111 Error 5111: Ftdvr Incompatable Tape Rates 5112 Error 5112: Ftdvr Invalid DMA Command 5113 Error 5113: Ftdvr Tape Header Not Read 5114 Error 5114: Ftdvr No Data Buffer 5115 Error 5115: Ftdvr Uncorrectable Error 5116 Error 5116: Ftdvr Abort 5141 Error 5141: An unrecoverable tape error has occurred. 5142 Error 5142: The tape is unreadable. 5143 Error 5143: Read error was corrected. 5144 Error 5144: The tape drive is not communicating with the floppy or parallel controller. 5145 Error 5145: CRC error. 5146 Error 5146: The tape drive was not in the ready mode. 5147 Error 5147: Syncronization error has occurred. 5148 Error 5148: Equipment check error has occurred. 5149 Error 5149: The tape has gone past the last track. 5150 Error 5150: An uncorrectable data error has occurred. 5151 Error 5151: DMA overrun -- check your hardware settings 5152 Error 5152: Floppy controller reports no data. 5154 Error 5154: Missing address -- an uncorrectable data error has occurred. 5155 Error 5155: Control mark -- an uncorrectable data error has occurred. 5156 Error 5156: Wrong cylinder -- an uncorrectable data error has occurred. 5157 Error 5157: Bad cylinder -- an uncorrectable data error has occurred. 5160 Error 5160: Invalid tape command has been sent. 5161 Error 5161: An abnormal termination has occurred. 5162 Error 5162: Cartridge not present. 5163 Error 5163: Unformatted tape. 5166 Error 5166: Invalid DMA channel specified in device configuration. 5167 Error 5167: Invalid interrupt number specified in device configuration. 5168 Error 5168: Invalid base address specified in device configuration. 5169 Error 5169: Unable to allocate memory in driver. 5170 Error 5170: The interrupt the tape drive is attempting to use is already in use. 5171 Error 5171: Tape drive report command failed. 5172 Error 5172: Unable to write to floppy controller. 5173 Error 5173: The tape drive cannot read from the floppy controller. 5174 Error 5174: Spurious interrupt. 5175 Error 5175: Floppy controller busy. 5176 Error 5176: Uncorrected Data Error 5177 Error 5177: Unsupported Controller 5178 Error 5178: Invalid Media 5179 Error 5179: Trace Point Error 1 5180 Error 5180: Trace Point Error 2 5181 Error 5181: Trace Point Error 5182 Error 5182: Empty Segment 5201 Error 5201: Out of Driver Memory 5202 Error 5202: IOCT Failed 5203 Error 5203: Driver Not Loaded 9400 Error 9400 Load Boot Record Failed 9401 Error 9401 Memory Error 9402 Error 9402 Disk Read Failed 9403 Error 9403 Disk Write Failed 9404 Error 9404 Disk Lock Failed 9405 Error 9405 Short Name Creation Failed 9406 Error 9406 C: Drive Not Formatted With Windows Format 10000 Iomega FullBack (TM) 10001 Performed 10002 Cartridge Sequence ID 10003 Space Used 10004 Compression 10005 Password Protected 10007 Recover.LOG 10008 No files are selected. 10009 Are you sure that you want to cancel the current operation? 10010 Retry 10011 Skip 10012 Cancel 10013 Yes 10014 No 10015 Ok 10016 Press Return to continue or ESC to quit 10017 Iomega FullBack (TM) (c) Copyright 1998 Iomega Corporation Version 1.0 10018 Iomega FullBack (TM) 10019 Right arrow expands tree Left arrow collapses tree Enter\Return shows files Space Bar toggles select F10 starts the restore F3 cancels screen 10020 SPC toggle select ESC to go back 10021 Please wait... 10022 TAB next window UP/DOWN selects ESC or F3 to quit RETURN to continue 10023 Size 10024 Last Write Date 10025 Last Write Time 10026 Flags 10027 Restore to 10028 Always 10029 Never 10030 Prompt 10031 If Newer 10032 Select the volume to restore 10033 File selection canceled. 10034 Error writing VIO display. 10035 Cancel the current operation? 10036 Volume Name 10037 No device was detected. If you do have a backup device attached to the machine, then choose Add Manually. 10038 Add Manually 10039 The default settings or device has changed. Would you like to configure the current backup device manually? 10040 Iomega Recovery will be unable to restore. 10041 No device was detected at these settings. Check the configuration of the drive to ensure that the settings are correct. 10042 An unknown error %d has occurred. 10043 Press ESC to cancel... 10044 No files were selected to restore 10045 An alternate path was not entered 10046 Invalid alternate path 10047 Configuring Drive...Please Wait 10048 Detecting...Please Wait 10049 Reading Volumes...Please Wait 10050 Reading Directory Structure...Please Wait 10051 Preparing To Restore...Please Wait 20000 Generic Controller 20001 Iomega ZIP 100 20002 Iomega ZIP 250 20003 Iomega JAZ 1GB 20004 Iomega JAZ 2GB 20005 Iomega Image File 20006 Unknown Iomega Device - 20007 Iomega Logical Drive 20100 218 20101 191 20102 192 20103 217 20104 196 20105 179 20106 201 20107 187 20108 200 20109 188 20110 205 20111 186 20112 32 20113 176 20114 219 20115 30 20116 31 20117 42 20118 0 20119 197 20120 58 20121 46 20122 340 20123 360 20124 370 20125 3E0 20126 3F0 20127 1 20128 2 20129 3 20130 4 20131 5 20132 6 20133 7 20134 9 20135 10 20136 11 20137 12 20138 14 20139 15 20140 IOMEGA FULLBACK (TM) 20141 Iomega Ditto Dash/DXJ 20142 Iomega Ditto Dash/DX