PTY
Section: Devices and Network Interfaces (4)
Index
Return to Main Contents
BSD mandoc
BSD 4.2
NAME
pty
- pseudo terminal driver
SYNOPSIS
pseudo-device pty
[count
]
DESCRIPTION
The
pty
driver provides support for a device-pair termed a
pseudo terminal
A pseudo terminal is a pair of character devices, a
master
device and a
slave
device. The slave device provides to a process
an interface identical
to that described in
tty(4).
However, whereas all other devices which provide the
interface described in
tty(4)
have a hardware device of some sort behind them, the slave
device has, instead, another process manipulating
it through the master half of the pseudo terminal.
That is, anything written on the master device is
given to the slave device as input and anything written
on the slave device is presented as input on the master
device.
In configuring, if an optional
count
is given in
the specification, that number of pseudo terminal pairs are configured;
the default count is 32.
The following
ioctl(2)
calls apply only to pseudo terminals:
- TIOCSTOP
-
Stops output to a terminal (e.g. like typing
`^S'
) .
Takes
no parameter.
- TIOCSTART
-
Restarts output (stopped by
TIOCSTOP
or by typing
`^S'
) .
Takes no parameter.
- TIOCPKT
-
Enable/disable
packet
mode. Packet mode is enabled by specifying (by reference)
a nonzero parameter and disabled by specifying (by reference)
a zero parameter. When applied to the master side of a pseudo
terminal, each subsequent
read
from the terminal will return data written on the slave part of
the pseudo terminal preceded by a zero byte (symbolically
defined as
TIOCPKT_DATA )
or a single byte reflecting control
status information. In the latter case, the byte is an inclusive-or
of zero or more of the bits:
- TIOCPKT_FLUSHREAD
-
whenever the read queue for the terminal is flushed.
- TIOCPKT_FLUSHWRITE
-
whenever the write queue for the terminal is flushed.
- TIOCPKT_STOP
-
whenever output to the terminal is stopped a la
`^S'
- TIOCPKT_START
-
whenever output to the terminal is restarted.
- TIOCPKT_DOSTOP
-
whenever
t_stopc
is
`^S'
and
t_startc
is
`^Q'
- TIOCPKT_NOSTOP
-
whenever the start and stop characters are not
`^S/^Q'
While this mode is in use, the presence of control status information
to be read from the master side may be detected by a
select(2)
for exceptional conditions.
This mode is used by
rlogin(1)
and
rlogind(8)
to implement a remote-echoed, locally
`^S/^Q'
flow-controlled
remote login with proper back-flushing of output; it can be
used by other similar programs.
- TIOCUCNTL
-
Enable/disable a mode that allows a small number of simple user
ioctl
commands to be passed through the pseudo-terminal,
using a protocol similar to that of
TIOCPKT
The
TIOCUCNTL
and
TIOCPKT
modes are mutually exclusive.
This mode is enabled from the master side of a pseudo terminal
by specifying (by reference)
a nonzero parameter and disabled by specifying (by reference)
a zero parameter.
Each subsequent
read
from the master side will return data written on the slave part of
the pseudo terminal preceded by a zero byte,
or a single byte reflecting a user control operation on the slave side.
A user control command consists of a special
ioctl
operation with no data; the command is given as
UIOCCMD (n)
where
n
is a number in the range 1-255.
The operation value
n
will be received as a single byte on the next
read
from the master side.
The
ioctl
UIOCCMD (0)
is a no-op that may be used to probe for
the existence of this facility.
As with
TIOCPKT
mode, command operations may be detected with a
select
for exceptional conditions.
- TIOCREMOTE
-
A mode for the master half of a pseudo terminal, independent
of
TIOCPKT
This mode causes input to the pseudo terminal
to be flow controlled and not input edited (regardless of the
terminal mode). Each write to the control terminal produces
a record boundary for the process reading the terminal. In
normal usage, a write of data is like the data typed as a line
on the terminal; a write of 0 bytes is like typing an end-of-file
character.
TIOCREMOTE
can be used when doing remote line
editing in a window manager, or whenever flow controlled input
is required.
FILES
- /dev/pty[p-r][0-9a-f]
-
master pseudo terminals
- /dev/tty[p-r][0-9a-f]
-
slave pseudo terminals
DIAGNOSTICS
None.
HISTORY
The
pseudo-device pty
driver appeared in
BSD 4.2
Index
- NAME
-
- SYNOPSIS
-
- DESCRIPTION
-
- FILES
-
- DIAGNOSTICS
-
- HISTORY
-
This document was created by
man2html,
using the manual pages.
Time: 02:55:24 GMT, December 08, 2024