Spezifikationen: Grafische Equalizer

Spezifikationen: Analoge Equalizer

Q2031B

GQ1031C

GQ2015A

FREQUENCY RESPONSE 20 Hz - 20 kHz, +/- 0.5dB @ +4dB* 600 ohms

TOTAL HARMONIC DISTORTION Less than 0.05% (THD+N), 20 Hz - 20 kHz @ +4 dB* 600 ohms, Equalizer...all flat (0dB)

HUM & NOISE
(Average, Rs=600 ohms BPF : 20Hz - 20kHz) -96 dB* -94 dB* -96 dB*

Equalizer ... all flat (0 dB), Input Level ... Max.

MAXIMUM VOLTAGE GAIN 0 dB, Input Level ... Max.

Center Frequencies: 31 band (1/3 octave)
20, 25, 31.5, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400, 500, 630, 800, 1k, 1.25k, 1.6k, 2k, 2.5k, 3.15k, 4k, 5k, 6.3k, 8k, 10k, 12.5k, 16k, 20kHz 15 band (2/3 octave)
25, 40, 63, 100, 160, 250, 400, 630, 1k, 1.6k, 2.5k, 4k, 6.3k, 10k, 16kHz

Variable Range: +/- 12dB , +/- 6dB

HIGH PASS FILTER
(Rolloff Frequency) 12dB/octave
(20 - 200Hz at -3dB point.) 12dB/octave (80Hz at -3dB point.)

PEAK LED INDICATOR Red LED on each channel turns on when post-EQ signal reaches the level 3 dB below clipping.

SIGNAL LED INDICATOR
Green LED on each channel turns on when post-EQ signal reaches the level 13 dB below nominal level

.

POWER REQUIREMENTS General Model : AC230V, 50Hz

POWER CONSUMPTION 20W 13W 15W

DIMENSIONS(W x H x D) 480 x 93.4 x 230mm (2HE) 480 x 49.4 x 230mm (1 HE)

WEIGHT 4.0kg 2.8kg 3.0kg

	Q2031B	GQ1031C	GQ2015A
FREQUENCY RESPONSE	20 Hz - 20 kHz, +/- 0.5dB @ +4dB* 600 ohms
TOTAL HARMONIC DISTORTION	Less than 0.05% (THD+N), 20 Hz - 20 kHz @ +4 dB* 600 ohms, Equalizer...all flat (0dB)
HUM & NOISE (Average, Rs=600 ohms BPF : 20Hz - 20kHz)	-96 dB*	-94 dB*	-96 dB*
Equalizer ... all flat (0 dB), Input Level ... Max.
MAXIMUM VOLTAGE GAIN	0 dB, Input Level ... Max.
Center Frequencies:	31 band (1/3 octave) 20, 25, 31.5, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400, 500, 630, 800, 1k, 1.25k, 1.6k, 2k, 2.5k, 3.15k, 4k, 5k, 6.3k, 8k, 10k, 12.5k, 16k, 20kHz	15 band (2/3 octave) 25, 40, 63, 100, 160, 250, 400, 630, 1k, 1.6k, 2.5k, 4k, 6.3k, 10k, 16kHz
Variable Range:	+/- 12dB , +/- 6dB
HIGH PASS FILTER (Rolloff Frequency)	12dB/octave (20 - 200Hz at -3dB point.)	12dB/octave (80Hz at -3dB point.)
PEAK LED INDICATOR	Red LED on each channel turns on when post-EQ signal reaches the level 3 dB below clipping.
SIGNAL LED INDICATOR	Green LED on each channel turns on when post-EQ signal reaches the level 13 dB below nominal level .
POWER REQUIREMENTS	General Model : AC230V, 50Hz
POWER CONSUMPTION	20W	13W	15W
DIMENSIONS(W x H x D)	480 x 93.4 x 230mm (2HE)	480 x 49.4 x 230mm (1 HE)
WEIGHT	4.0kg	2.8kg	3.0kg

* 0 dB is referenced to 0.775V RMS.

INPUT SPECIFICATIONS

INPUT Connectors

Input Impedance

Source Impedance

Input Level

Connectors **

Sensitivity *

Nominal Level

Maximum Before Clipping

INPUT(A,B) 15k ohms 600-ohm Lines +4 dB (1.23V) +4 dB (1.23V) +24 dB (12.3V) XLR-3-31 Type
Phone Jack (TRS)

OUTPUT SPECIFICATIONS

OUTPUT Connectors Output Impedance Load Impedance Output Level Connectors **

Nominal Level Maximum Before Clipping

OUTPUT(A,B) 150 ohms 600-ohm Lines +4 dB (1.23V) +24 dB (12.3V) XLR-3-32 Type
Phone Jack (TRS)(A, B)

INPUT Connectors	Input Impedance	Source Impedance	Input Level	Connectors **
Sensitivity *	Nominal Level	Maximum Before Clipping
INPUT(A,B)	15k ohms	600-ohm Lines	+4 dB (1.23V)	+4 dB (1.23V)	+24 dB (12.3V)	XLR-3-31 Type Phone Jack (TRS)

*The input level required to obtain the nominal output level.
**XLR-type connectors are balanced. 1=Ground, 2=+, 3=-
Phone jacks are balanced. T=+, R=-, S=Ground

(Alle Angaben ohne Gewähr.)

OUTPUT Connectors	Output Impedance	Load Impedance	Output Level		Connectors **
			Nominal Level	Maximum Before Clipping
OUTPUT(A,B)	150 ohms	600-ohm Lines	+4 dB (1.23V)	+24 dB (12.3V)	XLR-3-32 Type Phone Jack (TRS)(A, B)